Honeywell DVR HNDR S 4848 User Manual

HONEYWELL SECURITY TECHNICAL BULLETIN  
Honeywell Video Systems  
11 December 2008  
Subject: Control HNDR-S 4848 DVR by VideoBlox HEGS5BLX  
Introduction  
This document describes the Protocol Interface Translator (PIT) operation specific to the Honeywell HNDR-S  
series DVR. For further details on the PIT, please refer to the PIT User manual. For further details on the DVR,  
please refer to the appropriate Honeywell HNDR-S DVR manual.  
Quick Start Switch Settings  
Output  
S1/8  
S1/7  
S1/6  
S1/5  
S1/4  
S1/3  
S1/2  
S1/1  
Protocol  
Address  
ASCII  
string  
mode  
ASCII  
string  
mode  
ASCII  
string  
mode  
ASCII  
string  
mode  
Valid  
Function  
Valid  
Function  
Valid  
Function  
Valid  
Function  
Off  
Off  
Off  
Off  
On  
On  
On  
On  
S2/8  
S2/7  
S2/6  
S2/5  
S2/4  
S2/3  
S2/2  
S2/1  
Switch  
Legend  
Address  
7
Address  
6
Address  
5
Address  
4
Address  
3
Address  
2
Address  
1
Address  
0
0 (B/cast)  
Off  
Off  
Off  
Off  
Off  
Off  
Off  
Off  
Input  
Protocol  
S3/8  
S3/7  
S3/6  
S3/5  
S3/4  
S3/3  
S3/2  
S3/1  
Slave  
Port  
Baud  
Slave Port  
Baud  
Master  
Port Baud Port Baud  
Master  
Input  
Type  
Input  
Type  
Input  
Type  
Input  
Type  
Bossware  
On  
Off  
On Off  
On  
On  
On  
Off  
The above setting set the PIT as follows:  
Receive Betatech compatible Bossware control messages on the RS422 slave port of the PIT at 19.2K baud.  
The PIT unit address (S2/1 - S2/8 to OFF position) is set to broadcast, so all addresses will be translated. If  
want to control specific unit of DVR, set the dip switch S2/1 – S2/8 of PIT address and add PIT per DVR. (It is  
tested the address from 1 to 128.)  
Unit ID  
S2/8  
Off  
Off  
Off  
Off  
Off  
S2/7  
Off  
Off  
Off  
Off  
Off  
S2/6  
Off  
Off  
Off  
Off  
Off  
S2/5  
Off  
Off  
Off  
Off  
Off  
S2/4  
Off  
Off  
Off  
Off  
Off  
S2/3  
Off  
Off  
Off  
On  
On  
S2/2  
Off  
On  
On  
Off  
Off  
S2/1  
On  
Off  
On  
Off  
On  
1
2
3
4
5
:
255  
On  
On  
On  
On  
On  
On  
On  
On  
Transmit Honeywell HNDR-S control messages on the RS422 master port at 9600 baud, 8, N, 1 .  
Note: To control HNDR-S series DVR, the DVR firmware should be 1.0.17 or later.  
(Tested firmware: HVBCPUX – 4.96x  
HVBCFG – 3.08 (Build 32)  
HVBPIT44 – 3.03)  
Rev 1.0  
1 of 5  
 
HONEYWELL SECURITY TECHNICAL BULLETIN  
Device Configuration  
11 December 2008  
Go to Control page to configure external CCTV peripherals which may be controlled by VideoBloX keyboard.  
1. Copy the HNDR-S.db and HNDR-S.mb files to root directory “C:\Program  
Files\Honeywell\VBloXCFG\DBF\”  
2. Execute the VbloxCFG software and go to “Control” page.  
3. Select the “Device Type” which is to be configured.  
4. Click  
icon to browse “HNDR-S.db” which is locate in “C:\Program Files\Honeywell\VBloXCFG\DBF\”  
5. Set “Com Port” to “1” if the control signal to the device is connected to the VideoBloX CPU master  
communications port.  
6. Set the “Control Type” to the type of interface used to control the external device.  
7. Set “Switch Offset” to “-1” if no automatic video switch operation is required when the device is selected.  
The offset will be added to the selected device number and the resulting value will be used as the matrix  
video input channel which will be selected. e.g. Switch Offset =29, the first channel of HNDR-S DVR is  
input 30.  
8. Click “Download” button to download after changed.  
Rev 1.0  
3 of 5  
 
HONEYWELL SECURITY TECHNICAL BULLETIN  
11 December 2008  
HNDR-S 4848 DVR Configuration  
1. Configure Communication port  
a. Push Menu button of DVR and enter the DVR setting menu.  
b. Move to System menu and select Serial Setup.  
c. Move to COM2 485 and select Keyboard HTX-3000 as below figure.  
2. Configure Keyboard Control Address and Keyboard PTZ address as below figure.  
a. Push Menu button of DVR and enter the DVR setting menu.  
b. Move to Miscellaneous menu.  
c. Select Keyboard Control Address to 1.  
Rev 1.0  
4 of 5  
 
HONEYWELL SECURITY TECHNICAL BULLETIN  
HEGS5BLX Operation  
11 December 2008  
To select “HNDR-S 4848”, press “DVR” button. Then press “1” + “Enter” buttons to select DVR number 1.  
Joystick  
I
J
K
L
M
A
B
C
D
E
F
G
H
DVR Function Keys  
Item Function supported Description  
(The Keyboard should be in DVR mode for the below operation)  
by Keyboard  
1
2
Menu  
Press “H”  
Play  
Press “B”  
3
Rewind  
Forward  
Search  
Sequence  
Select  
Multi-screen  
Exit  
Press “G”  
4
AUX Mode LED on, Press “C”  
Press “C”  
5
6
Press “F”  
7
AUX Mode LED on, Press “E”  
AUX Mode LED on, Press “F”  
AUX Mode LED on, Press “G”  
AUX Mode LED on, Press “H”  
Hold down “ALT” + “Up”  
8
9
10  
11  
12  
13  
14  
Enter  
Up  
Down  
Hold down “ALT” + “Down”  
Hold down “ALT” + “Left”  
Left  
Right  
Hold down “ALT” + Right”  
I: Use to move between menu items  
J: Select DVR channel depending on the position  
K: Select DVR channel depending on the position  
L: Select DVR channel depending on the position  
M: Use to move between menu items  
15  
DVR channel select  
* Detail DVR operation procedure, please refer to the DVR manual.  
Note: The information contained herein is subject to change without notice.  
Rev 1.0  
5 of 5  
 

Graco Stroller QUATTRO TOUR SPORT User Manual
Graco Yard Vacuum 3000cc User Manual
Honeywell Crib Toy MKXXII User Manual
Honeywell Home Security System VISTA 128FBP User Manual
Hotpoint Video Game Controller CIB6441 CE User Manual
HP Hewlett Packard Projector mp3135 User Manual
Humminbird Fish Finder 343c User Manual
Humminbird Laminator LCR4 ID User Manual
Hunter Fan Thermostat 42202 User Manual
Hypertec Carrying Case N17118NHY User Manual