Instructions/Parts List
High Pressure
Fluid Regulators
309475F
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
II 2 G
List of Models
List of Models
Part No.
Series Model
Type
Maximum Fluid Inlet Pressure Regulated Pressure Range
233760
234266
B
B
P60-VP DN7
P60-VP DN7 npt
Pneumatic
5000 psi (36 MPa, 360 bar)
5000 psi (36 MPa, 360 bar)
5000 psi (36 MPa, 360 bar)
5000 psi (36 MPa, 360 bar)
5000 psi (36 MPa, 360 bar)
5000 psi (36 MPa, 360 bar)
2600 psi (18 MPa, 180 bar)
70-900 psi
(0.5-6 MPa, 5-60 bar)
233767
234264
B
B
P200-VM
P200-VM npt
Mechanical
Mechanical
Pneumatic
Pneumatic
Pneumatic
Mechanical
1300-3000 psi
(9-20 MPa, 90-200 bar)
233768
234265
B
B
P200-VM
P200-VM npt
1300-4000 psi
(9-27 MPa, 90-270 bar)
233769
234270
B
B
P150-VP DN7
P150-VP DN7 npt
300-2000 psi
(2-15 MPa, 20-150 bar)
233770
234271
B
B
P320-VP DN7
P320-VP DN7 npt
600-4600 psi
(4-32 MPa, 40-320 bar)
233813
234259
B
B
P250-VP
P250-VP npt
600-3600 psi
(4-25 MPa, 40-250 bar)
233814
234260
B
B
P100-VM
P100-VM npt
600-1500 psi
(4-10 MPa, 40-100 bar)
Back Pressure Regulators
Maximum Permanent Supply
Pressure
Part No.
Series Model
Type
Regulated Pressure Range
233771
234268
B
B
P100-RM
P100-RM npt
Mechanical,
back pressure
2500 psi (17 MPa, 170 bar)
600-1500 psi
(4-10 MPa, 40-100 bar)
233772
234269
B
B
P200-RM
P200-RM npt
Mechanical,
back pressure
3400 psi (23.5 MPa, 235 bar) 1300-3000 psi
(9-20 MPa, 90-200 bar)
Key to Model Designation
Pressure regulation valve e.g. P60- R
M
DN7 npt
npt version
Valve Seat Orifice 7mm
Operating Mode
P - pneumatic
M - mechanical
Action
V - pressure regulation
R - back-pressure regulation
Regulation max
60 bar
309475F
3
Warning
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
•
•
•
•
•
•
This equipment is for professional use only.
Read all instruction manuals, tags, and labels before operating the equipment.
Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
Check equipment daily. Repair or replace worn or damaged parts immediately.
Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
•
•
Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Techni-
cal Data section of all equipment manuals. Read the fluid and solvent manufacturer's warnings.
Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 180°F (82°C) or below -40°F (-40°C).
•
•
Wear hearing protection when operating this equipment.
Never use 1,1, 1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or flu-
ids containing such solvents in pressurized aluminum equipment. Such use could result in a chemi-
cal reaction, with the possibility of explosion.
•
Comply with all applicable local, state, and national fire, electrical, and safety regulations.
4
309475F
Warning
WARNING
SKIN INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause an
extremely serious injury, including the need for amputation. Splashing fluid in the eyes or on the skin can
also cause serious injury.
•
•
Fluid injected into the skin might look like just a cut, but is a serious injury. Get immediate surgical
treatment.
Do not point the gun at anyone or at any part of the body. Do not put your hand or fingers over the
spray tip. Do not stop or deflect fluid leaks with your hand, body, glove, or rag.
•
•
Never spray without the tip guard in place.
cleaning, checking, or repairing equipment.
•
•
Check the hoses and couplings daily. Replace worn, damaged, or loose parts immediately. Perma-
nently coupled hoses cannot be repaired; replace the entire hose.
Tighten all fluid connections before each use.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
•
•
Know the specific hazards of the fluid you are using. Read the fluid manufacturer’s warnings.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
•
Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
309475F
5
Introduction
Introduction
A fluid pressure regulator is used in air-assisted spray
systems to ensure accurate, positive control of fluid
pressure to a spray gun, dispensing valve, or atomizing
head.
Models 233767, 233814, 233768, 234260, 234264, and
234265 (FIG. 2.) are mechanically operated fluid pres-
sure regulators designed primarily for use with low to
medium viscosity fluids.
A regulator installed at a circulating line take-off or pump
reduces main line pressure to maintain the desired fluid
pressure to the spray gun, dispensing valve, or atomiz-
ing head.
Models 233760, 233769, 233770, 233813, 234259,
234266, 234270, and 234271 (FIG. 3.) are pneumati-
cally operated fluid pressure regulators designed pri-
marily for use with highly viscous coatings.
Models 233771, 233772, 234268 and 234269 (FIG. 1.)
are mechanically operated back pressure regulators that
limit the supply pressure to a set value by opening an
outlet and guiding back excess material when the prede-
termined pressure has been achieved. These valves are
used in circulating systems.
Adjustment knob
Spring
Valve plunger
Fluid Outlet
(Return line)
Fluid Inlet
(From gun)
TI1770A
Fig. 1. Cutaway of Mechanical Back Pressure Regulator
6
309475F
Introduction
Adjustment knob
Spring
Valve plunger
Fluid inlet
(from pump)
Fluid outlet
(to gun)
T I 1 7 6 9 A
TI1769A
Fig. 2. Cutaway of Mechanical Fluid Pressure Regulator
Air Inlet
Diaphragm
Valve plunger
Fluid Outlet
(To gun)
Fluid Inlet
(From pump)
TI1774A
Fig. 3. Cutaway of Pneumatic Fluid Pressure Regulator
309475F
7
Installation
Installation
1. Install one regulator for each spray gun.
b. Install a back pressure regulator downstream of
the gun. Connect the fluid return line from the
gun to the inlet of the back pressure regulator.
Connect the fluid return line to the pump to the
regulator’s outlet.
2. Apply thread sealant to connections as necessary.
3. Make sure that the direction of fluid flow agrees with
the flow direction markings on the regulator body.
a. Install a fluid pressure regulator upstream of the
gun: Connect the fluid line from the pump to the
inlet of the fluid regulator. Connect the fluid line
to the gun to the regulator’s outlet.
4. Flush and test the entire system.
for installing a system. They do not depict actual system
designs. Consult your Graco distributor for assistance in
designing a system that meets your specific require-
ments.
8
309475F
Installation
A
B
L
Air in
to pump
F
C
H
D
Air in
to gun
Y
B
H
E
K
Z
Fluid
M
G
G
J
Fluid in
TI1763C
Fig. 4. High pressure, non-circulating system, mechanical fluid regulator
Key
G
H
J
Fluid drain valve
Fluid shut-off valve
A
B
C
D
E
F
Air line filter
Mechanical fluid pressure regulator
Fluid pressure gauge
Air-assisted spray gun
Fluid filter
Bleed-type air shut-off valve
Pump air regulator
Gun air regulator
Fluid hose
K
L
M
Y
Z
Pump ground wire
Whip hose
Pump
309475F
9
Installation
A
B
A
B
L
N
Air to
Pump
Air to Fluid
Regulator
D
C
F
Air to
Gun
B
E
Y
K
Z
Fluid
H
G
M
J
G
TI1764C
Fig. 5. High pressure, non-circulating system, pneumatic fluid regulator
Key
J
Pneumatic fluid regulator
A
B
C
D
E
F
Air line filter
K
L
Fluid pressure gauge
Gun
Bleed-type air shut-off valve
Pump air regulator
Gun air regulator
Fluid hose
M
N
Y
Z
Fluid filter
Air regulator to operate/adjust fluid regulator
Pump ground wire
Pump
Whip hose
G
H
Fluid drain valve
Fluid shut-off valve
10
309475F
Installation
B
Air supply
D
H
A
Air to
gun
Fluid in
to gun
L
J
P
H
TI1765A
Fig. 6. High Pressure circulating system mechanical fluid regulator and back pressure regulator
Key
J
Mechanical fluid regulator
Gun
A
B
D
H
Air line filter
L
P
Bleed-type air shut-off valve
Pump air regulator
Fluid shut-off valve
Mechanical back pressure regulator
309475F
11
Operation
Operation
Flush Before First Use
Adjusting the Regulator
Your pressure regulator has been tested in the factory
with an anti-corrosion liquid. Before using the regulator,
thoroughly flush the system with a solvent to remove
residue of this liquid as well as any contaminants that
have been introduced during assembly of the system.
The fluid pressure regulator controls pressure down-
stream from its outlet. The inlet fluid pressure should
always be higher than the outlet fluid pressure.
If you are using an accessory fluid pressure gauge, trig-
ger the spray gun to relieve pressure in the line when
reducing the pressure, to ensure a correct gauge read-
ing.
Pressure Relief Procedure
Adjust the pump air pressure and the fluid pressure reg-
ulator for the best spraying combination.
WARNING
In a circulating system, the back pressure valve controls
the fluid pressure upstream of its inlet in the same way.
The system pressure must be manually relieved to
prevent the system from starting or spraying acciden-
tally. To reduce the risk of an injury from accidental
spray from the gun, splashing fluid, or moving parts,
follow the Pressure Relief Procedure whenever you:
Mechanical Regulator
1. Back out the knob until there is no spring pressure.
2. Turn on the fluid supply, to admit fluid to the regula-
tor.
•
•
•
•
are instructed to relieve the pressure
stop spraying
check or service any of the system equipment
or install or clean the spray tip.
3. Turn the knob clockwise to adjust fluid pressure to
the desired level.
1. Lock the gun trigger safety.
Pneumatic Regulator
1. With the fluid supply shut off, turn on the air pres-
sure to the regulator.
2. Close the bleed-type master air valve (required in
your system).
2. Turn on the fluid supply, to admit fluid to the regula-
tor.
3. Unlock the gun trigger safety.
4. Hold a metal part of the gun firmly to the side of a
grounded metal pail and trigger the gun to relieve
pressure.
3. Increase the fluid inlet pressure. When the fluid out-
let pressure is at the desired level, shut off the air to
the fluid regulator.
5. Lock the gun trigger safety.
6. Open the drain valve (required on your system), with
a container ready to catch the drainage.
7. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged or that pressure has not been fully relieved after
performing steps 1 through 7, very slowly loosen the tip
guard retaining nut or hose end coupling and relieve
pressure gradually. Then loosen completely and clear
the tip or hose.
309475F
13
Troubleshooting
Troubleshooting
Relieve the pressure (page 13) before checking or repairing the equipment.
To repair the regulator, refer to page 15.
Problem
Cause
Solution
Replace diaphragm.
Drop in fluid outlet pressure.
Ruptured diaphragm (17) (pneu-
matic regulators only).
Air escaping (pneumatic regulators
only).
Check air hose and connections.
Replace packings (13).
Replace packings (13).
Worn packings.
Fluid outlet pressure increases to
level of fluid inlet pressure.
Valve ball (8) and seat (4) are worn or Clean ball and seat. Replace worn or
stuck open.
damaged parts.
Fluid leaking from upper housing.
Ruptured diaphragm (17) (pneu-
matic regulators only).
Replace diaphragm.
Worn packings.
Replace packings (13).
14
309475F
Maintenance
Maintenance
Do not allow paint or solvent to sit in the system for
Flushing
extended periods. Fluid could dry on the plunger and
cause leakage at the plunger packings. If leakage
occurs, disassemble and clean the regulator.
WARNING
Cleaning and Repair
When changing fluids or colors, the regulator should be
disassembled and cleaned. Regular cleaning and
inspection of the internal parts is necessary to keep the
fluid regulator working properly.
The system pressure must be manually relieved to
prevent the system from starting or spraying acciden-
tally. Fluid under high pressure can be injected
through the skin and cause serious injury. To reduce
the risk of an injury from fluid injection, splashing fluid,
or moving parts, follow the Pressure Relief Proce-
dure whenever you:
1. Relieve all air and fluid pressure in the system.
2. Remove the regulator from the system.
•
•
•
•
are instructed to relieve the pressure
stop spraying
check or service any of the system equipment
or install or clean the spray tip.
3. Disassemble the regulator (see the parts drawings
4. Clean and inspect all parts.
1. Relieve the pressure.
CAUTION
2. Remove the spray tip. Clean the tip and set it aside.
Be very careful when handling the carbide balls and
seats. Damage will cause poor operation and leak-
age.
3. Supply solvent to the pump. Start the pump. Use the
lowest possible fluid pressure when flushing.
4. Flush the gun, spraying into a grounded metal con-
tainer until clean solvent comes from the gun.
5. Inspect the diaphragm, packings, o-rings, and seals
for wear. Check the ball and seat for nicks, wear, or
other damage.
5. Relieve the pressure.
6. Reinstall the spray tip.
6. Lubricate packings, o-rings and seals when reas-
sembling the regulator.
7. Torque as specified on the parts drawings on pages
309475F
15
Parts
Parts
Mechanical Regulators
Part Nos. 233767 (shown), 233768, 233814, 234260, 234264, and 234265
26
26
14
13
24
12
15
23
21
9
1
1
20
6
4
25
16
5
8
19
7
27
3
2
16
10
1
Torque to 25 N•m (18.5 ft-lb).
11
16
309475F
Parts
Mechanical Regulators
Part Nos. 233767 (shown), 233768, 233814, 234260, 234264, and 234265
Ref.
No.
Part No. Description
Qty
Ref.
No.
Part No. Description
HOUSING, lower
Qty
14
15
16
19
15A149
117125
15A178
117093
GLAND, female
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
RING, retaining, internal
PLATE, spring
HOUSING, lower (for npt version)
PLUG, screw
2
15A238
117089
245367
15Y030
15Y031
15A206
117104
245374
15A217
117112
15A223
15A142
SPRING, compression; for
233814 and 234260
3
SPRING, compression
SEAT, valve
117094
117088
SPRING, compression; for
233767, 233768, 234264, and
234265
1
1
4
5
O-RING
SPRING, compression; for
233768, 234265
6
O-RING
7
SUPPORT, ball
BALL, 5 mm
20
21
23
24
25
26
27
15A192
117103
15A240
15A203
117108
117098
15Y029
HOUSING, upper
SEAL, flat
1
1
1
1
1
2
1
8
9
PLUNGER, valve
HOUSING, packing
O-RING, slit
SCREW, custom
CAP
10
11
12
13
BALL, 8 mm
SCREW, set; M6x20
O-RING
GLAND, male
PACKING
309475F
17
Parts
Mechanical Back Pressure Regulators
Part Nos. 233771, 233772, 234268, and 234269 (shown)
26
10
26
24
11
14
13
23
21
12
15
9
1
1
20
6
25
16
4
5
27
19
16
2
1
Torque to 25 N•m
(18.5 ft-lb).
18
309475F
Parts
Mechanical Back Pressure Regulators
Part Nos. 233771, 233772, 234268, and 234269
Ref.
No.
Part No. Description
Qty
Ref.
Part No. Description
No.
Qty
15
16
19
117125
15A178
117093
RING, retaining, internal
1
2
1
1
HOUSING, lower
HOUSING, lower (for npt version)
PLUG, screw
1
1
1
1
1
1
1
1
1
1
3
1
PLATE, spring
SPRING, compression; for
233771 and 234268
2
15A238
245367
15Y030
15Y031
245376
15A217
117112
15A223
15A142
15A149
117094
SPRING, compression; for
233772 and 234269
1
4
SEAT, valve
5
O-RING
20
21
23
24
25
26
27
15A192
117103
15A240
15A203
117108
117098
15Y029
HOUSING, upper
SEAL, flat
1
1
1
1
1
2
1
6
O-RING
9
PLUNGER, valve
HOUSING, packing
O-RING, slit
SCREW, custom
CAP
10
11
12
13
14
BALL, 8 mm
SCREW, set; M6x20
O-RING
GLAND, male
PACKING
GLAND, female
309475F
19
Parts
Pneumatic Regulators
Part No. 233813 and 234259
1
Torque to 10 N•m (7.5 ft-lb).
1
26
29
30
9
20
17
11
1
16
18
6
4
5
8
7
27
3
14
13
2
TI1749A
12
15
20
309475F
Parts
Pneumatic Regulators
Part No. 233813 and 234259
Ref.
No.
Part No.
Description
Qty
Ref.
No.
Part No.
Description
Qty
12
13
14
15
16
17
18
20
26
27
29
30
15A223
15A142
15A149
117125
15A212
15A180
15A218
15A145
117128
15Y029
15C332
15C333
GLAND, male
1
3
1
1
1
1
1
1
6
1
1
1
PACKING
1
HOUSING, lower
1
GLAND, female
RING, retaining, internal
PLATE, diaphragm
DIAPHRAGM
HOUSING, lower (npt version only)
PLUG, screw
1
1
1
1
1
1
1
1
1
1
2
15A238
117089
245367
15Y030
15Y031
15A206
117104
245375
15Y033
3
SPRING, compression
SEAT, valve
HOUSING, diaphragm
COVER, diaphragm
SCREW, shcs; M8x50
O-RING
4
5
O-RING
6
O-RING
7
SUPPORT, ball
BALL, 5mm, carbide
PLUNGER, valve
O-RING
FITTING, (npt models only)
WASHER, (npt models only)
8
9
11
309475F
21
Parts
Pneumatic Regulators
Part Nos. 233760 (shown), 233769, 233770, 234266, 234270, and 234271
1
2
Torque to 10 N•m (7.5 ft-lb).
Torque to 12 N•m (8.8 ft-lb).
1
26
32
33
10
13
20
17
11
1
22
30
22
29
2
31
16
9
28
4
8
6
7
27
3
2
18
TI1745A
22
309475F
Parts
Pneumatic Regulators
Part Nos. 233760 (shown), 233769, 233770, 234266, 234270, and 234271
Ref.
No.
Part No.
Description
Qty
Ref.
No.
Part No.
15A187
15C298
Description
Qty
18
15A209
15A210
15A211
15A146
HOUSING, diaphragm; for 233760
and 234266
1
1
HOUSING, lower
1
HOUSING, diaphragm; for 233769
and 234270
1
1
1
HOUSING, lower (for npt version)
PLUG, screw
1
1
1
1
1
1
1
1
HOUSING, diaphragm; for 233770
and 234271
2
3
4
6
7
8
9
15A239
117091
245370
15Y031
15A207
117107
245377
SPRING, compression
SEAT, valve
20
COVER, diaphragm; for 233760 and
234266
15A147
15A148
COVER, diaphragm; for 233769 and
234270
1
1
O-RING
SUPPORT, ball
COVER, diaphragm; for 233770 and
234271
BALL, 8mm, carbide
PLUNGER, valve; for 233760,
234266,
22
26
27
28
29
30
31
32
33
15A220
117028
15Y032
117018
117030
117086
117100
15C332
15C333
RING (for non-npt models only)
SCREW, shcs; M6x16
O-RING
2
12
1
245379
PLUNGER, valve; for 233769,
233770, 234270, and 234271
1
10
11
13
16
245364
15Y034
117111
15A213
HOUSING, plunger
O-RING
1
1
1
1
WASHER
12
12
1
SCREW, shcs; M6x40
WASHER
SEAL, rod
PLATE, diaphragm; for 233760 and
234266
PLUG, threaded
1
FITTING (npt models only)
WASHER (npt models only)
1
15A214
15A215
15A181
15A182
15A183
PLATE, diaphragm; for 233769 and
234270
1
1
1
1
1
1
PLATE, diaphragm; for 233770 and
234271
17
DIAPHRAGM; for 233760 and
234266
DIAPHRAGM; for 233769 and
234270
DIAPHRAGM; for 233770 and
234271
309475F
23
Technical Data
Technical Data
Category
Data
Maximum Fluid Inlet
Pressure (Fluid Pressure
Regulators)
233814, 234260: 2600 psi (18 MPa, 180 bar)
233760, 233767, 233768, 233769, 233770, 233813, 234259, 234264, 234265,
234266, 234270, and 234271: 5000 psi (36 MPa, 360 bar)
Maximum Permanent Supply 233771, 234268: 2500 psi (17 MPa, 170 bar)
Pressure (Back Pressure
Regulators)
233772, 234269: 3400 psi (23.5 MPa, 235 bar)
233760, 234266: 70-900 psi (0.5-6 MPa, 5-60 bar)
Pressure Range
233767, 233772, 234264, 234269: 1300-3000 psi (9-20 MPa, 90-200 bar)
233768, 234265: 1300-4000 psi (9-27 MPa, 90-270 bar)
233769, 234270: 300-2000 psi (2-15 MPa, 20-150 bar)
233770, 234271: 600-4600 psi (4-32 MPa, 40-320 bar)
233771, 233814, 234268, 234260: 600-1500 psi (4-10 MPa, 40-100 bar)
233813, 234259: 600-3600 psi (4-25 MPa, 40-250 bar)
Maximum Operating Air
Pressure (Pneumatic
Regulators Only)
233760, 233770, 233813, 234259, 234266, 234271: : 85 psi (0.6 MPa, 6 bar)
233769, 234270: 75 psi (0.5 MPa, 5 bar)
Maximum Flow Rate
Temperature Range
233767, 233768, 233771, 233772, 233813, 233814, 234259, 234260, 234264,
234265, 234268, 234269: 32-194°F (0-90°C)
233760, 233769, 233770, 234266, 234270, 234271: 50-176°F (10-80°C)
233767, 233768, 233771, 233772, 233813, 233814, : 3/8 BSPP(F)
Fluid inlet and outlet
234259, 234260, 234264, 234265, 234268, 234269: 3/8 npt(F)
233760, 233769, 233770: 3/4 BSPP(F)
234266, 234270, 234271: 3/4 npt(F)
Air inlet
233760, 233769, 233770, 233813: 1/4 BSPP(F)
234259, 234266, 234270, 234271: 1/4 npt(M)
*Gauge port
Wetted Parts
233760, 233769, 233770, 234266, 234270, 234271: 1/4 BSPP(F)
233767, 233768, 233771, 233772, 233813, 233814, 234259, 234260, 234264,
234265, 234268, 234269: Stainless steel, tungsten carbide, PTFE, chemically
resistant fluoroelastomer
233760, 233769, 233770, 234266, 234270, 234271: UHMWPE, Stainless steel,
acetal, tungsten carbide, PTFE, chemically resistant fluoroelastomer
*Accessory Gauges Available
24
309475F
Accessory Gauges
Accessory Gauges
Model
Gauge
233760
234266
233769
234270
234770
234271
118340
118340
118341
118341
118341
118341
309475F
25
Flow Rate Data
Flow Rate Data
Maximum fluid flow with 10 weight oil, regulator wide open and no downstream restrictions.
Part No.
Inlet Fluid Test Pressure
Inlet/Outlet Size
Fluid Flow
233760
234266
5000 psi (36 MPa, 360 bar)
3/4 BSPP(F)
3/4 npt(F)
11.3 gpm (42.9 lpm)
233767
234264
233768
234265
3000 psi (21 MPa, 210 bar)
3660 psi (25 MPa, 256 bar)
4000 psi (28 MPa, 280 bar)
3800 psi (26 MPa, 266 bar)
2500 psi (17 MPa, 170 bar)
3400 psi (23.5 MPa, 235 bar)
3800 psi (26 MPa, 266 bar)
2500 psi (17 MPa, 170 bar)
3/8 BSPP(F)
3/8npt(F)
3/8 BSPP(F)
3/8npt(F)
8.2 gpm (31.2 lpm)
9.2 gpm (35.0 lpm)
11.7 gpm (44.5 lpm)
12.3 gpm (46.7 lpm)
10.2 gpm (38.8 lpm)
13.1 gpm (49.8 lpm)
10.6 gpm (40.3 lpm)
8.1 gpm (30.8 lpm)
233769
234270
233770
234271
233771
234268
3/4 BSPP(F)
3/4npt(F)
3/4 BSPP(F)
3/4npt(F)
3/8 BSPP(F)
3/8npt(F)
233772
234269
233813
234259
233814
234260
3/8 BSPP(F)
3/8npt(F)
3/8 BSPP(F)
3/8npt(F)
3/8 BSPP(F)
3/8npt(F)
Mounting Dimensions
Part No.
Thread
Dimension A
233768
234265
M5
28 mm (1.10 in.)
233769
234270
M6
M6
M5
M5
M5
M5
36 mm (1.42 in.)
36 mm (1.42 in.)
28 mm (1.10 in.)
28 mm (1.10 in.)
28 mm (1.10 in.)
28 mm (1.10 in.)
A
233770
234271
233771
234268
233772
234269
Part No.
Thread
Dimension A
233813
234259
233760
234266
M6
36 mm (1.42 in.)
233814
234260
233767
234264
M5
28 mm (1.10 in.)
26
309475F
03/2006
Mounting Dimensions
309475F
27
Graco Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1-800-328-0211 Toll Free
612-623-6921
612-378-3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 309475
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2002, Graco Inc. is registered to ISO 9001
Revised 2/2009
|
