iLive Speaker System 1407 0603 09 User Manual

USER’S GUIDE  
V:1407-0603-09  
IS809B  
Wireless Speaker System  
For the most up-to-date version of this Users Guide, go to www.ilive.net  
 
FCC Warnings  
Whats Included  
NOTE: This equipment has been tested and found to  
comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the following  
measures:  
IS809B  
Wireless Remote Control  
Docking Brackets for iPod  
Documentation  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and  
receiver.  
• Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
Features  
Dock plays and charges iPod  
Wireless speakers  
Supports up to 20 speakers  
• Advanced hi-fi sound with Channel Purity®  
Wireless remote  
Additional Warnings  
Digital volume control  
Pairing button  
Left, right, or mono selections  
Weather resistant  
• Digital 2.4GHz ISM wireless transmitter  
• LCD display with white backlight  
Digital clock  
This device complies with RSS 210 of Industry Canada.  
Operation is subject to the following two conditions:  
(1) this device may not cause interference, and (2)  
this device must accept any interference, including  
interference that may cause undesired operation of this  
device.  
• Play/pause, skip up/down functions for iPod  
On/Off, mute, function and pairing controls  
Independent volume settings for each speaker  
Transmission range: up to 200ft (line of sight) and  
90ft indoors  
• Auxiliary input for iPod shuffle and other audio  
devices  
• AC power: built-in AC cord  
• DC power: requires 6 D batteries per speaker, not  
included  
Lutilisation de ce dispositif est autorisée seulement  
aux conditions suivantes: (1) il ne doit pas produire de  
brouillage et (2) l’utilsateur du dispositif doit éntre prét a  
accepter tout brouillage radioélectrique recu, meme si ce  
brouillage est susceptible  
de compromettre le fonctionnement du dispositif.  
The term “IC” before the equipment certificationnumber  
only signifies that the Industry Canada technical  
specifications were met.  
This equipment complies with Industry Canada Radio  
Frequency Electromagnetic Signal (RF) exposure limits  
set forth for an uncontrolled environment of portable  
transmission.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | IS809B  
3
 
POWERING THE BASE STATION AND REMOTE  
Base Station AC Power  
Base Station Battery Backup  
Power the base station by connected it to a  
standard AC outlet using the attached AC power  
cord.  
Requires 2 AAA batteries (not included).  
The battery backup is meant for keeping the clock  
and timer settings during short unexpected power  
outages. The unit’s other features cannot function  
off of the battery backup alone.  
Remote  
Requires 2 AAA batteries (not included).  
Power the remote by inserting 2 AAA batteries into  
the battery compartment on the back of the remote.  
4
iLive | IS809B  
 
POWERING THE WIRELESS SPEAKERS  
Wireless Speaker AC Power  
Power the wireless speakers by connected them to  
a standard AC outlet using the attached AC power  
cord.  
The AC cord is stored inside of the wireless  
speaker’s battery compartment.  
After extending the AC cord out from the battery  
compartment, snap the battery compartment door  
back into position to keep the internal elements of  
the wireless speaker from being exposed.  
Wireless Speaker DC Battery Power  
Requires 6 D batteries (not included).  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | IS809B  
5
 
INTRODUCTION  
Timer  
Press and hold to set  
the timer.  
Dock for iPod  
Dimmer  
Use to connect an iPod  
to the wireless speaker  
system.  
Press to adjust the  
brightness on the  
wireless speaker  
system’s display  
Source  
Press to switch between  
iPod and Auxiliary  
modes.  
Power  
Press to turn the unit  
off and on.  
Link Indicator  
Indicates the current  
status of the base  
station’s wireless  
link with the wireless  
speakers.  
Play/Pause  
Press to play or pause a  
docked iPod.  
Skip/Search  
Press to skip forwards  
or backwards through  
tracks on a docked  
iPod.  
Press and hold to  
search forwards or  
backwards through an  
individual track on a  
docked iPod.  
Display  
Sleep  
Press repeatedly to set  
the sleep timer.  
Time Set  
Press and hold to set  
the wireless speaker  
system’s clock.  
Auxiliary Input  
Use to connect an  
external audio source  
to the wireless speaker  
system.  
Pair  
Press and hold to  
pair the base station  
with nearby wireless  
speakers.  
6
iLive | IS809B  
 
Power  
Press to turn the unit  
off and on.  
Mute  
Press to mute the  
volume of the unit.  
Source  
Press to switch between  
iPod and Auxiliary  
modes.  
Play/Pause  
Press to play or pause a  
docked iPod.  
Repeat  
Press to activate the  
repeat options on a  
docked iPod.  
Random  
Press to activate the  
shuffle option on a  
docked iPod.  
Skip/Search  
Press to skip forwards  
or backwards through  
tracks on a docked  
iPod.  
Bass  
Press and hold to  
search forwards or  
backwards through an  
individual track on a  
docked iPod.  
Press to adjust the level  
of bass output from the  
linked speakers.  
Treble  
Volume  
Press to adjust the  
volume of the unit.  
Press to adjust the level  
of treble output from  
the linked speakers.  
Special Note  
The included remote is wireless and does  
not require line-of-sight to control the  
unit.  
Battery Compartment  
Located on the back of  
the remote. Requires  
2 AAA batteries, not  
included.  
The wireless remote can control the unit  
from approximately half the distance of  
the speaker reception. (Approximately  
100ft line-of-sight, or 45ft indoors  
depending on location)  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | IS809B  
7
 
Left/Right/Mono  
Adjust to switch  
between Left, Right,  
snd Mono speaker  
modes.  
Speaker Volume  
Turn to adjust the  
volume of the wireless  
speaker.  
Pair  
Press and hold to pair  
the speaker with nearby  
base stations.  
Power  
Press to turn the  
speaker off and on.  
Battery Compartment  
Requires 6 D batteries,  
not included.  
AC Power Cord  
Link Indicator  
Use to connect the  
wireless speaker to a  
standard AC outlet.  
Indicates the current  
status of the wireless  
speaker’s link with the  
base station.  
8
iLive | IS809B  
 
PAIRING THE WIRELESS SPEAKERS WITH THE BASE STATION  
Pairing  
What does it mean to Pair?  
Pairing the base station with a wireless  
The two wireless speakers included in the same  
speaker allows the base station to recognize  
that wireless speaker. Once paired, the base  
station will remember that wireless speaker and  
transmit audio through it.  
box as the base station are pre-paired with that  
base station. Any additional speakers will need to  
be paired by following the directions below.  
When pairing the base station with a wireless  
speaker you will need to press the Pair button  
on the base station and wireless speaker  
simultaneously. Because of this, you will need to  
have both the base station and wireless speaker  
within reach when you pair them.  
Link Indicators  
Off  
Powered off.  
1. Plug the base station into a power source,  
and press the Power button to power the base  
station on.  
Slow Flashes  
Standby mode.  
Quick Flashes  
Attempting to pair.  
The base station Link Indicator will flash when  
the base station is powered on.  
Solid Light  
Paired and playing.  
2. Plug the wireless speaker into a power source  
or insert 6 D batteries, not included, and press  
the Power button to power the wireless speaker  
on.  
If the base station is not playing audio, either from  
the dock for iPod or the Auxiliary input, then both  
the base station and wireless speakers will go into  
Standby mode. Once you begin playing audio from  
the base station, both the base station and wireless  
speaker will come out of Standby mode.  
The wireless speaker Link Indicator will flash  
when the wireless speaker is powered on.  
3. Adjust the Volume on the wireless speaker to  
approximately the half-way point between min.  
and max volume.  
Transmission Range  
4. Simultaneously press and hold the Pair button  
on the base station and the Pair button on the  
wireless speaker for 5 seconds.  
Once the base station is paired with a wireless  
speaker, the wireless speaker can be moved  
approximately 200ft (line-of-sight) or 90ft  
(indoors) and still receive audio from the base  
station.  
5. The wireless speaker will emit a long beep  
when it is paired with the base station.  
If the wireless speaker emits short repeating  
beeps, it was not able to pair with the base  
station. Repeat steps 1-4 until you hear the  
long beep.  
Results will vary depending on the number and  
size of obstructions between the base station and  
the wireless speaker.  
After pairing, the wireless speaker may take up to  
30 seconds to begin playing audio from the paired  
base station.  
How many speakers can I pair to  
one base station?  
Up to 20 wireless speakers can be paired with  
one base station. Additional speakers are sold  
separately.  
Repeat steps 1-4 for each additional wireless  
speaker you want to pair with the base station.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | IS809B  
9
 
OPERATIONS  
Setting the Clock  
Setting the Timer  
1. Press and hold the Time Set button.  
1. Press and hold the Timer button.  
2. While holding the Time Set button, press the  
Skip/Search buttons to adjust the hour and  
minute.  
2. While holding the Timer button, press the  
Skip/Search buttons to adjust the hour and  
minute.  
3. Release the Time Set button to set the adjusted  
3. Release the Timer button to set the adjusted  
time.  
timer.  
4. Press the Source button to select iPod or  
Auxiliary mode.  
Setting the Sleep Timer  
An iPod must be docked, or an audio source  
must be connected to the Auxiliary input when  
the set time is reached. Otherwise, no audio  
will play when the set time is reached.  
1. Press the Sleep button repeatedly to adjust the  
sleep timer between 60 and 10 minutes, in 10  
minute increments.  
When the set amount of time has expired, the  
unit will power off.  
5. Press the Power button to turn the unit off.  
6. Press the Timer button to activate the set timer.  
“Timer On” will appear on the LCD display  
when the timer is activated.  
Using the Auxiliary Input  
Note: The speakers need to be paired with the unit  
before any audio can be heard.  
After the set time is reached, the base station  
will power on.  
1. Connect a mini-phono 3.5mm cable (not  
included) or a mini-phono 3.5mm cable-RCA  
R/L audio cable (not included) to the Auxiliary  
Input on the unit and the audio output/  
headphone jack on an MP3 player, television,  
or stereo system.  
IMPORTANT: The wireless speakers must be  
powered on manually before the set time is  
reached. The timer will not power on the paired  
wireless speakers.  
Using the Wireless Remote  
2. Turn the unit on by pressing the Power button.  
The included remote is wireless and does not  
require line-of-sight to control the unit.  
3. Press the Source button to switch the unit to  
Auxiliary mode.  
The wireless remote can control the base station  
from approximately half the distance of the  
speaker reception. (Approximately 100ft line-of-  
sight, or 45ft indoors)  
4. Audio played through the connected MP3  
player, television, or stereo system will now be  
heard through the unit.  
Audio Source  
Required Connector  
Results will vary depending on the number and  
size of obstructions between the base station  
and the wireless remote.  
MP3 Player  
mini-phono 3.5mm Cable (not  
included)  
The Volume buttons on the remote control will  
adjust the master volume of the base station,  
affecting all linked speakers.  
Television  
mini-phono 3.5mm Cable -  
RCA R/L Audio Cable (not  
included)  
The included speakers have independent  
volume controls that can be used to fine tune  
the volume of the individual speakers.  
Stereo System  
mini-phono 3.5mm Cable -  
RCA R/L Audio Cable (not  
included)  
10 iLive | IS809B  
 
OPERATIONS  
Docking an iPod  
Left / Right / Mono Speaker Settings  
1. Locate the numbered bracket that fits the iPod  
The wireless speakers can be set to Left, Right, or  
Mono by using the Left/Right/Mono dial on the  
wireless speaker.  
that will be docked.  
Each included Bracket has a number on it,  
indicating which iPod model that bracket is  
compatible with. See the separate bracket  
chart page to identify which bracket is needed.  
When placing multiple wireless speakers in close  
proximity to one another, set half of the speakers  
to Left and the other half to Right. This will create  
a stereo audio output.  
2. Snap the bracket into place over the iPod  
connector in the Dock for iPod.  
When a single wireless speaker is set in a location,  
adjust the Left/Right/Mono dial to Mono.  
3. Connect the iPod to the iPod connector.  
When the unit is plugged in, using AC power,  
the docked iPod will charge.  
Resetting the Unit  
Resetting the base station is the quickest and most  
effective way to solve small unexpected problems  
with the base station’s behavior.  
1. Using a paperclip or like object, press the  
Reset button to reset the base station to it’s  
original settings.  
Please note, resetting the base station will not  
unpair any of the wireless speakers from the  
bast station.  
Playing a Docked iPod  
Note: The wireless speakers need to be paired with  
the unit before any audio can be heard. See page 9  
for wireless speaker pairing instructions.  
1. Press the Power button to turn the base station  
on.  
2. Press the Source button to switch to iPod  
mode.  
3. Press the Play/Pause button to play or pause  
the docked iPod.  
CUSTOMER HELPLINE | 1-314-621-2881  
iLive | IS809B 11  
 
COMPANY INFORMATION  
International Support  
To download this User’s Guide in English,  
Spanish, or French, visit the support section at  
Para transferir esta guía de usuario en inglés,  
español, o francés, visite la sección de la ayuda en  
Pour télécharger ce guide de l’utilisateur en  
anglais, espagnol, ou français, visitez la section de  
Contact Information  
Address: 2116 Carr Street, St. Louis MO, 63106  
Phone: 1-314-621-2881  
Fax: 1-314-588-1805  
Parts Email: [email protected]  
© 2009 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners. Specifications are  
subject to change without notice  
 

Grindmaster Blender 5512 User Manual
Grundig Flat Panel Television LW49 7710BS User Manual
Grundig MP3 Player 30GB User Manual
Hamilton Beach Rice Cooker 37538N User Manual
Hasselblad Camera Lens CFE 4 120 User Manual
Honeywell Air Cleaner F50E User Manual
Honeywell Humidifier HE225A User Manual
HP Hewlett Packard Personal Computer DV2500 User Manual
HP Hewlett Packard Server 686713 S01 User Manual
iHome MP3 Docking Station iH17 User Manual