Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from
defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.
Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period,
SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing,
return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product
to the Factory Service Center listed below. The product must include proof of purchase, including date of purchase. The fee for service
without proof of purchase is $30.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective
batteries are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty
period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of
purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Dr.
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions
may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies
product.
For any other questions: 1-800-288-2792 Toll Free
iH31HIB-072106-0
Printed in China
iH31H
1
Table of Contents
IMPORTANT...................................................................................................................................................................1
A Consumer Guide to Product Safety....................................................................................................................3-4
FCC Information.........................................................................................................................................................5
Getting Started...........................................................................................................................................................6
Install iPod Insert
Install Power..............................................................................................................................................................7-8
Install AC Adaptor
Install/Replace Battery
Batteries information
Install/Replace the Remote Control Battery
Maintenance...............................................................................................................................................................8
Controls and Indicators............................................................................................................................................9
Charging your iPod/iPod Shuffle............................................................................................................................10
Listening to iPod/iPod Shuffle................................................................................................................................11
Listening to non-docking iPod or other portable audio devices......................................................................12
Listening to FM Radio..............................................................................................................................................12
Presetting Your Favorite FM Station.....................................................................................................................13
Presetting a Station
Tuning into a Preset Station
Operating the Remote On/Off Switch...................................................................................................................13
Headphone Jack Operation....................................................................................................................................13
Trouble Shooting.................................................................................................................................................14-17
Warranty Information...............................................................................................................................................18
Download from Www.Somanuals.c2om. All Manuals Search And Download.
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to assure your personal
safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and
operating instructions carefully before installation and use. Keep these instructions handy for future reference.
Take special note, and adhere to all warnings on the unit and in the instruction and service manual.
1. Water and Moisture - The unit should not be used near water. For example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc.
2. Ventilation - The unit should be situated so that its location or position does not interfere with its proper
ventilation. For example, it should not be situated on a bed, sofa, rug, or similar surface that may block the
ventilation openings; or placed in a built-in installation, such as bookcase or cabinet that may impede the
flow of air through the ventilation openings.
3. Heat - The unit should be situated away from heat source such as radiators, heat register, stoves, or other
appliances (including amplifiers) that produce heat.
4. Power Sources - The unit should be connected to a power supply only of the type described in the operat-
ing instructions or as marked on the appliance.
5. Power Cord Protection – Power supply cord should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them. It is always best to have a clear area from where the cord
exits the unit to where it is plugged into an AC outlet.
6. Cleaning - The unit should be cleaned only as recommended by the manufacturer.
7. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
3
A Consumer Guide to Product Safety
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall outlet and disconnect the antenna
or cable system during a lightning storm or when it is left unattended and unused for long periods of time.
This will prevent damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
11. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
A. The power-supply cord or plug has been damaged.
B. Objects have fallen into or liquid has been spilled into the enclosure.
C. The unit has been exposed to rain.
D. The unit has been dropped or the enclosure damaged.
E. The unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or
longer, the power cord should be unplugged and take out batteries from the unit to prevent damage or corro-
sion.
14. Servicing - The user should not attempt to service the unit beyond that described in the user’s operating
instructions. All other servicing should be referred to qualified service personnel.
For any other questions: 1-800-288-2792 Toll Free
4
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that
this device does not cause harmful interference.
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These
limits provide reasonable protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate
interference you can try one or more of the following corrective measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the radio or TV.
• Use outlets on different electrical circuits for the equipment and the radio or TV.
Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate
the system’s warranty and void your FCC authorization to operate it.
5
Getting Started
Thank you for purchasing the iHome iH31H portable Stereo System for your iPod. Designed specifically to work
with your iPod, this system provides high quality audio and radio performance that invites your music to come
out and play.
Please read this instruction carefully before the appliance is operated and keep it for future reference.
Protective Dock Cover
Your iH31H comes with a removable clear protective cover at the front of the iPod dock. This should be removed
before placing inserts/docking your iPod and to access manual control of your iPod. To remove protective cover,
slide upwards when docking door is open.
Install iPod Insert
Your iH31H comes with 3 removable inserts and a rubber pad to ensure your iPod fits properly in the iPod
drawer. Please see below table to insert/replace rubber pad to fit your iPod.
Thick iPod
(no Insert needed)
5G iPod
iPod with video
Nano Insert
Thin iPod Insert
Shuffle
Mini Insert
Replace rubber pad
per instruction on the
5G rubber pad card
Dock into the Shuffle
connector located in the
top of the unit
iPod Nano
2/4GB
iPod 4G
iPod Photo
20 GB iPod 4G
20/30 GB iPod Photo 60 GB
40 GB
Use with
iPod Mini
To place an insert:
1. Select the insert for your iPod (see chart above).
Using the correct insert/rubber pad ensures the
proper fit to your iPod.
2. Press ᕩ Docking Door Open Button and put the insert gently into docking bay.
3. Please note that iPod must not be in a case or “skin”.
Note: This device will not control or charge the 3G iPod.
6
Install Power
Connect AC Adaptor
Connect the AC adaptor cable plug into the jack on the back of the system, then plug the AC adaptor into the
wall outlet. When connected to the AC adaptor, the iH31H charges your iPod/iPod Shuffle and allows you to play
it and the radio.
Note: The iPod/iPod Shuffle does NOT charge when the iH31H is operating on batteries. This AC adaptor is for
use with the iH31H only. To avoid damage, do not use another kind of adaptor with the iH31H.
Install/Replace Batteries
1. Open the battery compartment cover located on the bottom of the
unit.
2. Insert 8 “C” batteries, checking that the + and – ends of the batteries
match the drawing inside the battery compartment. We recommend
the use of alkaline batteries for longer life. Different types of batteries
or new and used batteries are not to be mixed.
3. Close the compartment cover.
Install Unit Battery
Batteries information:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
• Make sure you dispose of batteries properly (see your local regulations).
7
Install Power
Install/Replace the Remote Control Battery
The remote control battery is installed at the factory. When the remote control stops operating or its range
seems reduced, it is time to replace the battery with a new one.
1. Open the battery compartment cover located on the bottom of the
Battery
remote control unit.
door
latch
2. Insert a CR2032 battery, checking the + and – ends of the battery
matches the drawing inside the battery compartment.
3. Close the compartment cover.
To check for iPod compatibility
iH31H is an advanced system and supports most updated iPod features. To make sure your iPod works
properly with the iH31H, please update your iPod firmware with the latest one. Please check the Apple web-
site for the same (http://www.apple.com/ipod/download).
Maintenance
• Place the unit away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such
as Benzine, paint thinner or similar materials can mar the surface of the case.
8
Controls and Indicators
Power On/Off Button ᕡ
FM Preset Button µ
ꢅ iPod/ FM/ AUX Mode Select Button
ꢄ iPod Shuffle Dock
ꢆ iPod Play/Pause Button
ꢀ Tune Down Button
ꢁ Tune Up Button
_
ꢃ Volume Button
ꢂ Volume + Button
ᕩ Docking Door Open Button
iPod Dock
ᕡ Power On/Off Button
Headphone Jack ¸
ꢇ Mode Button
ꢆ Play/Pause Button
ꢁ Tune Up Button
Line-in Jack ¹
ꢀ Tune Down Button
Mute Button ƽ
Remote Control
Storage Compartment
ꢂ Volume + Button
_
ꢃ Volume Button
FM Antenna Ƹ
µ 6 FM Preset Buttons
Note: The remote control will not control iPod shuffle
ꢈ Remote On/Off Switch
ꢉ Mono / Stereo FM Switch
AC Adaptor Jack ƹ
Shuffle Cap ƺ
9
Charging your iPod/iPod Shuffle
Note: Please make sure you are using the correct insert for your iPod (see Install iPod Insert on page 6) and that
it is properly docked into the iH31H. Failure to do so may damage your iPod.
1. Your iPod/iPod Shuffle recharges (until fully charged) while it is docked in the system and the iH31H is
connected to an outlet with the included AC power adaptor. Your iPod/iPod Shuffle will NOT charge
when the unit is running on battery power. The iH31H does NOT control or charge 3G iPod models.
Sh
uffl
e
S
ong
s
Ba
ck
lig
ht
Install iPod
Install iPod Shuffle
10
Listening to iPod/iPod Shuffle
1. Dock the already playing iPod. The iH31H will automatically turn on and you will hear the music playing from
your iPod.
Note: If the song/music loudness playing on the iPod itself is too low, iH31H may not detect the iPod is in
play mode. Press the ꢆ iPod Play/Pause Button on the iH31H or the remote control twice to play it.
2. When the iPod is docked and in standby mode, press the ꢆ iPod Play/Pause Button on the iH31H or the
remote control to play it. The iPod Icon will appear at the right lower corner of the display.
3. Press the ꢆ iPod Play/Pause Button again to pause play; press again to resume it.
4. Press the ꢂ Volume+ and ꢃ Volume– Button on the iH31H or the remote control to adjust the system
volume. Press ƽ Mute Button to mute the output; press the button again to release it.
5. Press the ꢊ Tune Up or ꢋ Tune Down Button on the iH31H or the remote control to go to the previous
or next track. Press and hold while a track is playing for high speed forward or reverse music search of the
current track.
6. To turn off the unit, press the ᕡ Power On/Off Button on the iH31H or the remote control to turn it off. Your
iPod will continue charging while in the dock (when using the AC adaptor).
Note: The iH31H cannot control Shuffle functions. For iPod Shuffle operation, you need to switch iPod Shuffle
on or off, and play or pause it, etc., manually.
Note: If you are using an iPod Shuffle, for best audio performance, adjust Shuffle volume to eliminate sound
distortion.
Note: The iH31H dock will not charge the 3G ipod.
Note: The remote control will not control iPod shuffle.
Note: When running the iH31H on batteries, if the iPod is not used for 14 hrs / 36 hrs (depending on iPod model ),
it may enter “deep sleep” mode and not respond to iH30H control. To wake up your iPod, press and hold the
Menu button on your iPod until the Apple logo appears.
11
Listening to Non-docking iPod or other portable audio devices
If you are using an iPod without a docking port or other MP3 player or other portable audio device, you can
still play it through the iH31H via the Line-in Jack.
1. Plug one end of the audio patch cord (included) into the headphone or line-out jack on your device and the
other end of the patch cord into the iH31H ¹ Line-in Jack, located on the front of the unit.
2. Press ᕡ Power On/Off Button on main unit or remote to turn iH31H on.
3. Press the ꢇ Mode Button until you can see “AU” showing on the display, indicating AUX playing mode.
4. Press the ꢂ Volume+ and ꢃ Volume– Button on main unit or remote control to adjust the system
volume. You may need to adjust your device volume too.
5. To turn off the unit, press the ᕡ Power On/Off Button on main unit or remote control to turn it off. Please
remember to turn off your device, too.
Listening to FM Radio
Note: Extend FM rod antenna fully for best reception. In some areas, it may be difficult to get stereo sound
without interference. If this proves a problem, set the ꢉ Mono/Stereo FM switch on the back of the unit
to Mono.
1. Press the ᕡ Power On/Off Button on the iH31H or remote to turn unit on.
2. Press the ꢇ Mode Button on the iH31H or remote control until you can see a radio frequency showing on
the display.
3. Use ꢊ Tune Up or ꢋ Tune Down Button to tune in to the desired station.
4. Press and hold the ꢊ Tune Up or ꢋ Tune Down Button for appox. 2 seconds, it will start to auto seek
available stations and will stop when a clear one is found.
5. Press the ꢂ Volume+ and ꢃ Volume– Button on the iH31H or remote control to adjust the iH31H
volume. Press the ƽ Mute Button to mute the output; press the button again to release it.
6. To turn off the unit, press the ᕡ Power On/Off Button on the iH31H or the remote control to turn it off.
12
Presetting Your Favorite FM Station
You can preset 6 FM stations (the unit does not receive AM radio).
Presetting a Station
1. Following step 1 to 5 in Listening to Radio and manually tune into the station you wish to preset.
2. Hold down one of the six µ Preset Buttons you wish to preset for approx. 2 seconds. You will hear 2
beep tones to confirm the station is stored.
3. To preset another station, repeat above steps. To change the preset station, tune into the desired station
and hold down the µ Preset Button. The new station will replace the previous station.
Tuning into a Preset Station
1. Turn on the unit and press the ꢇ Mode Button on the iH31H or the remote control to turn on the radio.
2. Press the desired µ Preset Button. The corresponding station will show on the display.
3. Press the ꢂ Volume+ and ꢃ Volume– Button on the iH31H or the remote control to adjust the system
volume.
4. To turn off the unit, press the ᕡ Power On/Off Button on main unit or remote control to turn it off.
Operating the Remote On/Off Switch
To save battery power, switch off the ꢈ Remote On/Off Switch for longer battery life. The switch will not
function while using the AC adaptor.
Headphone Jack Operation
Connect a headphone (not included) to the ¸ Headphone Jack in the front of the unit for private listening.
The built-in speakers are shut off when the headphone is connected.
Download from Www.Somanuals1.co3m. All Manuals Search And Download.
Trouble Shooting
Symptom
Possible Problem
Solution
Unit doesn’t respond AC adaptor isn’t plugged to a wall outlet or the
Plug the AC adaptor into a wall outlet and plug the
connector into the power supply jack on the unit
(no power)
connector is not plugged into the power supply
jack on the back of the unit
Plug another device into the same outlet to
confirm the outlet is working
Wall outlet is not functioning
iPod cannot dock
properly
Using no or wrong iPod insert
iPod is not installed properly
Make sure the dock insert is the proper fit for your iPod
Remove your iPod from the dock and check for any
obstruction on the connectors in the dock and on
your iPod. Then reseat it in the dock.
iPod does not
respond to the
unit
Remove your iPod from the dock and check for any
obstruction on the connectors in the dock and on
your iPod. Then reseat it in the dock.
iPod is not installed properly
Upgrade software on your iPod. For details, visit
Your iPod software is too old
iPod is locked up
Please make sure your iPod is working properly before
docking it to the unit. Please refer to your iPod manual
for details on iPod operation.
Using 1st or 2nd generation iPod, iPod Shuffle or
other device
iH31H cannot control those iPods or other devices.
14
Trouble Shooting
Symptom
Possible Problem
Solution
iPod didn’t
charge up
iPod is not installed properly
Remove your iPod from the dock and check for
obstruction on the connectors in the dock and
on your iPod. Then reseat it in the dock.
Please make sure your iPod is working properly
before docking it in the unit. Please refer to your
iPod manual for detail.
iPod is locked up/frozen
iPod battery has problem
Charging 3G iPod
3G iPod is not supported
Sound is distorted
Volume level is set too high
Sound source is distorted
Decrease the unit and/or iPod Shuffle volume
If iPod original sound source is poor quality, distortion
and noise are easily noticed with high-power speak-
ers.
Try a different audio source such as a music CD.
If you are using an iPod Shuffle or external sound
source like older generation iPod, try reducing the
output volume on the device itself. Also, try turning
bass boost OFF.
Remote Control
didn’t work
Replace with new battery
Battery weak
Remote Control is not pointed toward the
IR sensor
Point the Remote Control toward the IR sensor, within
10 feet of the unit.
Remote On/Off Switch is activated
Move Remote switch to ON position
15
Solucionando problemas
Síntoma
Causa
Solución
La unidad no
funciona (no circula
corriente eléctrica)
El adaptador de AC no está conectado al
tomacorriente o el conector no está conectado
a la ficha en la parte posterior de la unidad
Conecte el adaptador de AC al tomacorriente y
también conecte el conector a la ficha en la parte
posterior de la unidad
Coloque otro aparato en ese mismo tomacorriente para
confirmar si el que no funciona es el tomacorriente
El tomacorriente no funciona
El iPod no encastra
correctamente
No ha colocado el encastre del iPod, o está
utilizando el encastre incorrecto.
Verifique que el encastre sea el apropiado para su iPod
Quite el iPod del encastre y retire la posible obstruc-
ción del encastre o de su iPod. Vuelva a colocar el
iPod dentro del encastre.
El iPod no encastra correctamente
El iPod no se
comunica con la
unidad
Quite el iPod del encastre y verifique posibles
obstrucciones del encastre o de su iPod. Vuelva a
colocar el iPod dentro del encastre.
El iPod no está instalado correctamente
Renueve su software. Para mayor información, diríjase
Su software es obsoleto
El iPod no responde
Verifique que su iPod funcione correctamente antes
de conectarlo a la unidad. Refiérase al manual de su
iPod para más detalles.
Usted tiene un iPod de primera o segunda
generación, un Shuffle u otro tipo de aparato
El iH31H no puede controlar estos otros aparatos
16
Solucionando problemas
Síntoma
Causa
Solución
El iPod no carga
El iPod no está instalado correctamente
Quite el iPod del encastre y retire la posible
obstrucción del encastre o de su iPod. Vuelva a
colocar el iPod dentro del encastre.
Por favor asegúrese de que su iPod funcione correcta-
mente antes de colocarlo en el encastre. Refiérase al
manual de su iPod para mayor información.
El iPod está trabado/no responde
La batería del iPod podría tener algún inconveniente
El volumen se encuentra muy alto
El sonido sale
distorsionado
Baje el volumen
Si el sonido original de su iPod era de pobre calidad, las
distorsiones y ruidos se harán más notables con los
parlantes de alta potencia. Pruebe utilizar otra fuente de
audio como un CD.
El sonido sale distorsionado de la unidad
Si está utilizando un iPod de primeras generaciones o
un Shuffle, intente bajar el volumen de su aparato.
También intente apagar el amplificador de bajos
El control remoto
no funciona
Reemplace las baterías por nuevas
Las baterías están gastadas
No está apuntando el control remoto
hacia el iH31H
Apunte el control remoto hacia el iH31H y mantén-
gase a una distancia máxima de 10 pies de la unidad.
El selector On/Off remoto está activado
Mueva el selector remoto a la posición ON
17
|