1
531870-1_A
Transducer Switch
Thank You
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by
designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird® accessories
offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment.
In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free
of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For
complete details, see the Warranty section included in this manual.
Contact our Customer Resource Center at 1-800-633-1468 or visit our Web site at humminbird.com.
Installation Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read
these instructions carefully in order to get the full benefit from your Humminbird® accessory. If you find that any items
are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our Web site at
humminbird.com.
Transducer Switch
The Transducer Switch comes with all the necessary hardware to allow you to connect your control head to two
transducers. The transducers may be the same type of transducer with different mounting locations, or you can
maximize your unit’s performance by using two different transducers. The switch is intended for installation on the
console, and will work well on almost any boat.
Supplies: In addition to the hardware supplied with your Transducer Switch, you will need a hand drill with various
size bits, a Phillips screwdriver, an adjustable wrench, and a 3 amp fuse.
Installation
Perform the procedures in the following sections to install the Transducer Switch on your boat. Before installing the
Transducer Switch, gather all the parts you will need, and make sure that the planned location of the Transducer
Switch will allow you to connect the two transducers to your control head.
1.
Locating the Transducer Switch Mounting Position
There are two ways to find the mounting location, as follows:
Switch Panel: If your console already contains a switch panel with an available slot, slide the Transducer Switch into
the designated slot until it snaps into place. Then skip ahead to procedure two.
In-Dash: If your console does not have a switch panel or a pre-made mounting location, you will need to create one
yourself.
Mounting the Switch
Boat Console
Switch
© 2011 Humminbird®, Eufaula AL, USA.
All rights reserved.
3
531870-1_A
Transducer Switch
NOTE: Use caution while sliding the transducer connectors into the Transducer Switch connectors. The slots for the
connectors are keyed to prevent reversed installation, so do not force the connectors together. See your control head
installation guide for additional information.
To connect the connector clips to the Transducer Switch:
Connecting the Connector Clips
to the Transducer Switch
1. From the back side of the panel, plug the two connector clips from the switch assembly into the two outlets of
the Transducer Switch.
Switch
NOTE: Connecting the connector clips to the Transducer Switch does not require a specific order; either connector will work
with either outlet.
To connect the control head to the Transducer Switch:
Connector Clips
1. Remove the connector holder from your control head.
2. Insert the Transducer Switch cable connector into the T2 slot (transducer slot) of the connector holder.
NOTE: The slots are keyed to prevent reversed installation, so be careful not to force the connector into the holder. See your
control head installation guide for additional information.
700 SERIES™ NOTE: If you are installing the Speed Sensor accessory (optional), insert the Sonar/Speed Y-Cable connector
into the T2 slot on the connector holder. Then, connect the transducer connector and speed sensor connector to the
corresponding connectors on the Y-Cable. The Y-Cable requires a separate purchase. Contact our Customer Resource Center
for details at 1-800-633-1468 or visit our Web site at humminbird.com.
3.
Connecting the Power Cable
Connect the Transducer Switch power cable to the boat’s fuse panel (usually located near the console). If you must
connect to a battery, connect to a battery switch (not included).
Connecting to a Fuse Panel
1a. If a fuse terminal is available, use crimp-on type electrical connectors (not included) that match the terminal on
the fuse panel. Attach the black wire to ground (-), and the red wire to positive (+) 12 VDC power. Install a 3 amp
fuse (not included) for protection of the unit. Humminbird® is not responsible for over-voltage or over-current
failures.
or...
1b. If you need to wire the control head to a battery, obtain and install an inline fuse holder, a 3 amp fuse (not
included) for the protection of the unit, and a battery switch (not included). Install the battery switch using the
instructions provided with it.
NOTE: If you are unable to obtain a battery switch and are forced to connect the power cable directly to the battery, be
aware that this may cause a slow loss of power over time. See procedure five, Powering Off.
NOTE: Humminbird® is not responsible for over-voltage or over-current failures. The control head must have adequate
protection through the proper selection and installation of a 3 amp fuse.
2. Secure the installation with cable ties (optional).
Your Transducer Switch is now ready for operation.
© 2011 Humminbird®, Eufaula AL, USA.
All rights reserved.
4
531870-1_A
Transducer Switch
Changing Transducers
in the Menu System
4.
Switching Transducers
Perform the following procedures to alternate between the transducers connected to your Transducer Switch.
To activate a transducer:
1. Press the Transducer Switch to select the desired transducer.
2. Turn on your control head.
3. In any view, press the MENU key twice to open the Main Menu.
4. Press the RIGHT or LEFT Cursor keys to highlight the Sonar menu tab.
5. Press the DOWN Cursor key to select Transducer Select.
6. Press the RIGHT or LEFT Cursor keys again to select a transducer.
Sonar Menu
5.
Powering Off
It is important to make sure all accessories (switches, control heads, etc.) are powered off in order to avoid possibly
draining the battery. To make sure your Transducer Switch is disengaged, follow the steps below.
If your Transducer Switch is connected to the fuse panel,
1. Power off your boat to disengage the switch.
If your Transducer Switch is connected to a battery switch,
1. Turn the dial of the battery switch to the OFF position.
If your Transducer Switch is connected directly to a battery,
1. Power off your boat.
2. Remove the Transducer Switch wires from the battery.
© 2011 Humminbird®, Eufaula AL, USA.
All rights reserved.
|