Hotpoint Washer Dryer WDL 540 P G A K User Manual

Instructions for use  
WASHER-DRYER  
!
This symbol reminds you to read this booklet.  
GB  
GB  
Contents  
English, 1  
Installation, 2-3-4-5  
Unpacking and levelling  
Connecting the electricity and water supplies  
The first wash cycle  
Technical data  
Description of the Washer-dryer and  
starting a wash cycle, 6-7  
Control panel  
Indicator lights  
Starting a wash cycle  
Wash cycles, 8  
Table of wash cycles  
WDL 540 P/G/A/K  
Personalisation, 9  
Setting the temperature  
Setting the drying cycle  
Functions  
Detergents and laundry, 10  
Detergent dispenser drawer  
Preparing the laundry  
Garments requiring special care  
Load balancing system  
Precautions and tips, 11  
General safety  
Disposal  
Care and maintenance, 12  
Cutting off the water or electricity supply  
Cleaning the Washer-dryer  
Cleaning the detergent dispenser drawer  
Caring for the door and drum of your appliance  
Cleaning the pump  
Checking the water inlet hose  
Troubleshooting, 13-14  
Assistance, 15-16  
1
 
Connecting the drain hose  
the supply voltage is included within the values  
indicated on the Technical details table  
(see page 5);  
GB  
Connect the drain hose,  
without bending it, to a  
draining duct or a wall  
drain situated between  
65 and 100 cm from the  
floor;  
the socket is compatible with the washing  
machine’s plug. If this is not the case, replace  
the socket or the plug.  
65 - 100 cm  
Your appliance is now supplied with a 13 amp fused plug  
it can be plugged into a 13 amp socket for immediate  
use. Before using the appliance please read the instruc-  
tions below.  
The drain hose may be  
connected to an under-  
sink trap. Before connec-  
ting the drain hose from  
the machine ensure that  
any blanks or removable  
ends have been taken off  
the spigot.  
WARNING - THIS APPLIANCE MUST BE EARTHED.  
THE FOLLOWING OPERATIONS SHOULD BE CARRIED  
OUT BY A QUALIFIED ELECTRICIAN.  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA approved  
fuse to BS 1362 should always be used, and the fuse  
cover re-fitted. If the fuse cover is lost, the plug must  
not be used until a replacement is obtained.  
Replacement fuse covers:  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
If a replacement fuse cover is fitted, it must be of the  
correct colour as indicated by the coloured marking or  
the colour that is embossed in words on the base of the  
plug. Replacements can be obtained directly from your  
nearest Service Depot.  
If it is place over the  
edge of a basin or sink  
be sure the free end of  
the hose should not be  
underwater.  
Removing the plug:  
If your appliance has a non-rewireable moulded plug and  
you should wish to re-route the mains cable through  
partitions, units etc., please ensure that either:  
the plug is replaced by a fused 13 ampere re-wearable  
plug bearing the BSI mark of approval.  
! We advise against the use of hose extensions; in case  
of absolute need, the extension must have the same  
diameter as the original hose and must not exceed 150  
cm in length.  
or:  
the mains cable is wired directly into a 13 amp cable  
outlet, controlled by a switch, (in compliance with BS  
5733) which is accessible without moving the appliance.  
Ensure that if the drain hose is pushed into a standpi-  
pe, that the end does not go down more than 15cms  
(6 inches). If the hose is pushed down too far, this may  
cause the machine to self -syphon ie. continuously  
empty as it is filling.  
Disposing of the plug:  
Ensure that before disposing of the plug itself, you  
make the pins unusable so that it cannot be accidentally  
inserted into a socket.  
Electric connection  
Instructions for connecting cable to an alternative plug:  
Important: the wires in the mains lead are coloured in  
accordance with the following code:  
Before plugging the appliance into the mains socket,  
make sure that:  
Green & Yellow Earth  
Blue  
Brown  
Neutral  
Live  
the socket is earthed and in compliance with  
the applicable law;  
the socket is able to sustain the appliance’s  
maximum power load indicated in the Technical  
details table (see page 5);  
3
 
As the colours of the wires in the lead may not corre-  
spond with the coloured markings identifying the termi-  
nals in your plug, proceed as follows:  
Connect Green & Yellow wire to terminal marked E or  
or coloured Green or Green & Yellow.  
The first wash cycle  
GB  
Once the appliance has been installed, and before you  
use it for the first time, run a wash cycle with detergent  
and no laundry, using the wash cycle 1.  
Connect Brown wire to terminal marked L or coloured  
Red.  
Connect Blue wire to terminal marked N or coloured  
Black.  
If a 13 amp plug (BS 1363) is used it must be fitted with  
a 13 amp fuse, either in the plug or adaptor or at the  
distribution board.  
If you are in any doubt about the electrical supply to  
your machine, consult a qualified electrician before use.  
How to connect an alternative plug:  
The wires in this mains lead are coloured in accordance  
with the following code:  
BLUE  
BROWN  
NEUTRAL (N)  
LIVE (L)  
GREEN & YELLOW  
EARTH (E)  
GREEN &  
YELLOW  
13 ampere fuse  
BROWN  
BLUE  
CROSS-BAR  
CORD GRIP  
Disposing of the appliance:  
When disposing of the appliance please remove the plug  
by cutting the mains cable as close as possible to the plug  
body and dispose of it as described above.  
! The Washer-dryer should not be installed in an out-  
door environment, not even when the area is sheltered,  
because it may be very dangerous to leave it exposed to  
rain and thunderstorms.  
! When the Washer-dryer is installed, the mains socket  
must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent or dange-  
rously compressed.  
! The power supply cable must only be replaced by an au-  
thorised serviceman.  
Warning! The company denies all liability if and when  
these norms are not respected.  
4
 
GB  
Technical data  
Model  
WDL 540 P/G/A/K  
width 59.5 cm  
height 85 cm  
depth 53.5 cm  
Dimensions  
Capacity  
from 1 to 7 kg for the wash programme  
from 1 to 5 kg for the drying programme  
Electrical  
please refer to the technical data plate  
fixed to the machine  
connections  
maximum pressure 1 MPa (10 bar)  
Water connections minimum pressure 0.05 MPa (0.5 bar)  
drum capacity 52 litres  
Spin speed  
up to 1400 rotations per minute  
Wash: programme 1; temperature 60°C;  
using a load of 7 kg.  
Drying: first drying cycle performed with  
2 kg load, by selecting the  
dryness level.;  
the second drying cycle performed with  
Energy rated  
programmes  
according to  
regulation  
EN 50229  
5 kg load, by selecting the  
dryness level.  
This appliance conforms to the following  
EC Directives:  
- 2004/108/EC (Electromagnetic Compatibility)  
- 2006/95/EC (Low Voltage)  
- 2002/96/EC  
5
 
Description of the Washer-dryer and  
starting a wash cycle  
Control panel  
GB  
WASH CYCLE PROGRESS indicator  
lights  
DRYING  
knob  
ON/OFF button  
DOOR  
LOCKED  
indicator light  
TEMPERATURE  
knob  
START/PAUSE  
button with  
Detergent dispenser drawer  
indicator light  
FUNCTION  
buttons with  
indicator lights  
WASH CYCLE  
knob  
Detergent dispenser drawer: used to dispense de-  
tergents and washing additives (see “Detergents and  
laundry”).  
START/PAUSE button with indicator light: starts or  
temporarily interrupts the wash cycles.  
N.B. To pause the wash cycle in progress, press this  
button; the corresponding indicator light will flash  
orange, while the indicator light for the current wash  
cycle phase will remain lit in a fixed manner. If the DOOR  
ON/OFF button: switches the Washer-dryer on and off.  
WASH CYCLE knob: programmes the wash cycles. During  
LOCKED  
indicator light is switched off, the door may  
the wash cycle, the knob does not move.  
be opened (wait approximately 3 minutes).  
To start the wash cycle from the point at which it was  
interrupted, press this button again.  
FUNCTION buttons with indicator light: used to select the  
available functions. The indicator light corresponding to  
the selected function will remain lit.  
Standby mode  
This washing machine, in compliance with new energy  
saving regulations, is fitted with an automatic standby  
system which is enabled after about 30 minutes if no  
activity is detected. Press the ON-OFF button briefly  
and wait for the machine to start up again.  
TEMPERATURE knob: sets the temperature or the cold  
wash cycle (see “Personalisation”).  
DRYING knob: used to set the desired drying program-  
me (see “Personalisation”).  
WASH CYCLE PROGRESS indicator lights: used to mo-  
nitor the progress of the wash cycle.  
The illuminated indicator light shows which phase is in  
progress.  
DOOR LOCKED indicator light: indicates whether the  
door may be opened or not (see next page).  
6
 
Door locked indicator light  
Indicator lights  
GB  
If this indicator light is on, the appliance door is locked to  
prevent it from being opened accidentally; to avoid any  
damage, wait for the indicator light to switch off before you  
open the appliance door (wait approximately 3 minutes).  
The indicator lights provide important information.  
This is what they can tell you:  
Wash cycle phase indicator lights  
! If the START/PAUSE indicator light (orange) flashes  
rapidly at the same time as the function indicator light,  
this indicates a problem has occurred (see “Troublesho-  
oting”).  
Once the desired wash cycle has been selected and has begun,  
the indicator lights switch on one by one to indicate which  
phase of the cycle is currently in progress.  
Wash  
Rinse  
Note: as soon as a drying level  
or time period has been set,  
this indicator light illuminates  
to indicate that the selected  
wash cycle will be followed by  
a drying phase.  
Spin  
Dry  
End of wash cycle  
Note: during the “Drain” phase, the indicator light corre-  
sponding to the “Spin” cycle phase will illuminate.  
Function buttons and corresponding indicator lights  
When a function is selected, the corresponding indicator  
light will illuminate.  
If the selected function is not compatible with the pro-  
grammed wash cycle, the corresponding indicator light will  
flash and the function will not be activated.  
If a function which is incompatible with another function  
selected previously, only the most recent selection will  
remain active.  
Starting a wash cycle  
1. Switch the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds,  
then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indica-  
tor light will flash.  
2. Load the laundry and close the door.  
3. Set the WASH CYCLE knob to the desired programme.  
4. Set the washing temperature (see “Personalisation”).  
5. Set the drying cycle if necessary (see “Personalisation”).  
6. Measure out the detergent and washing additives (see “Detergents and laundry”).  
7. Select the desired functions.  
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a  
fixed manner, in green.  
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.  
9. At the end of the wash cycle the  
indicator light will switch on. The DOOR LOCKED indicator light will switch off,  
indicating that the door may be opened (wait approximately 3 minutes). Take out your laundry and leave the appliance  
door ajar to make sure the drum dries completely. Switch the Washer-dryer off by pressing the ON/OFF button.  
7
 
Wash cycles  
Table of wash cycles  
GB  
Max. load  
(kg)  
Cycle  
duration  
Detergents  
Fabric  
Max. Max.  
temp. speed Drying  
Description of the wash cycle  
(°C)  
(rpm)  
Mini  
Mini  
load  
Wash  
Normal  
Normal  
softener  
load  
Essentials cycles  
Cottons: extremely soiled whites.  
Cottons (1): heavily soiled whites.  
1
1
1
2
3
4
90°  
60°  
40°  
60°  
40°  
50°  
1400  
1400  
1400  
1400  
1400  
800  
7
7
7
7
7
3
3
3
160  
155  
150  
130  
85  
105  
100  
95  
Cottons (2): lightly soiled whites and delicate colours.  
Cottons: heavily soiled whites and resistant colours.  
Coloureds Cottons (3): lightly soiled and delicate colours.  
Synthetics: heavily soiled resistant colours.  
3
3
100  
70  
3
1.5  
80  
65  
Fastwash 60': to refresh lightly soiled garments quickly (not  
suitable for wool, silk and clothes which require washing by hand).  
5
60°  
1400  
3
-
60  
-
Special cycles  
Baby cycle: heavily soiled delicate colours.  
6
7
40°  
40°  
30°  
40°  
30°  
800  
600  
800  
800  
0
-
2
2
1
1
-
120  
70  
60  
55  
55  
95  
65  
-
Shirts  
Ready to wear (*)  
8
1
Wool: for wool, cashmere, etc.  
Silk: for garments in silk and viscose, lingerie.  
Drying cycles  
9
1.5  
1
1
1
50  
50  
10  
11 Cottons  
12 Synthetics  
13 Wool  
-
-
-
-
-
-
-
-
-
-
-
-
5
3
-
-
-
-
-
-
-
-
-
1.5  
Partials wash cycles  
Rinse Fast  
A
B
C
-
-
-
1400  
1400  
0
-
-
-
-
-
7
7
7
3
-
35  
15  
2
30  
-
Spin Fast  
Pump out  
-
-
-
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration  
can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balan-  
cing and any wash options selected.  
For all Test Institutes:  
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 1 with a temperature of 60°C.  
2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.  
3) Short wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.  
(*) Ready to Wear  
This cycle was designed to wash and dry lightly soiled small loads quickly. By selecting this cycle it is possible to  
wash and dry a maximum load of 1 kg in just 60 minutes.  
!
Please note, this is an automatically programmed wash and dry cycle, therefore it is not possible to manually  
set a drying time or drying level in conjunction with this cycle.  
!
Please note, the Drying indicator illuminates only during the drying phase of the cycle, not when the cycle is  
first selected.  
Anti-crease  
This function interrupts the wash programme, and the washing is left to soak in water before the appliance is drained.  
It can only be used with programme 10 (Silk) and helps to prevent the formation of creases.  
To complete the cycle press the START/PAUSE button.  
8
 
Personalisation  
Setting the temperature  
GB  
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).  
The temperature may be lowered, or even set to a cold wash ( ).  
The Washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum value  
set for each wash cycle.  
Table of Drying times (guideline values)  
Setting the drying cycle  
Turn the DRYING knob to set the desired drying type.  
Fabric  
type  
Max.  
load (kg) dry  
Cupboard Henger Iron  
Load type  
dry  
dry  
Two options are available:  
A - Based on time: from 40 to 180 minutes.  
B - Based on the how damp the clothes are once they  
have been dried:  
Clothing of diffe-  
rent sizes, Terry  
towels  
Cotton  
5
180  
170  
140  
Iron : slightly damp clothes, easy to iron.  
Synthe-  
tics  
Sheets, Shirts, Py-  
jamas, socks, etc.  
3
140  
150  
120  
140  
100  
120  
Hanger  
: dry clothes to put away.  
Cupboard : very dry clothes, recommended for to-  
welling and bathrobes.  
If your laundry load to be washed and dried is much  
greater than the maximum stated load (see adjacent  
Knitwear, Pullo-  
vers. etc.  
Wool  
1.5  
table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them  
back in the drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the  
remainder of the load.  
N.B: when the drying is complete there is a cooling period, even though the DRYING knob is in the  
position.  
Drying only  
Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select the  
desired drying duration using the DRYING knob.  
Functions  
The various wash functions available with this Washer-dryer will help to achieve the desired results, every time.  
To activate the functions:  
1. Press the button corresponding to the desired function;  
2. the function is enabled when the corresponding indicator light is illuminated.  
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction  
with the selected wash cycle.  
Slow Spin (1400-600)  
By selecting this function, reduces the spin speed.  
! This function may not be used in conjunction with wash cycles 8, 10, 11, 12, 13, C.  
Mini load  
This function is recommended for when the load of laundry is equal to half, or less than half, of the maximum recom-  
mended load (see Table of wash cycles).  
! This function may not be used in conjunction with wash cycles 5, 8, 11, 12, 13, B, C.  
Extra rinse  
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is  
particularly useful for sensitive skin.  
! This function may not be used in conjunction with wash cycles 8, 11, 12, 13, B, C.  
Super Wash  
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle dura-  
tion, this function offers a high-performance wash.  
! This function may not be used in conjunction with wash cycles 5, 8, 9, 10, 11, 12, 13, A, B, C.  
9
 
Detergents and laundry  
Garments requiring special care  
Detergent dispenser drawer  
GB  
Baby cycle: this wash cycle 6 can be used to remove the  
soiling typically caused by babies, while ensuring that all  
detergent is removed from nappies in order to prevent  
the delicate skin of babies from suffering allergies.  
The cycle has been designed to reduce the amount  
of bacteria by using a greater quantity of water and  
optimising the effect of special disinfecting additives  
added to the detergent.  
At the end of the wash cycle, the machine will slowly  
rotate the drum to prevent the formation of creases;  
to end the cycle press the START/PAUSE button.  
Shirts: use special wash cycle 7 to wash shirts in various  
fabrics and colours.  
Good washing results also depend on the correct dose  
of detergent: adding too much detergent will not neces-  
sarily result in a more efficient wash, and may in fact a  
build up on the inside of your appliance and contribute  
to environmental pollution.  
! Do not use hand washing detergents because these  
create too much foam.  
Open the detergent di-  
spenser drawer and pour  
in the detergent or wa-  
shing additive, as follows.  
*
1
It guarantees maximum care is taken of the garments  
and minimises the formation of creases.  
2
Wool: all wool garments can be washed using programme  
9, even those carrying the “hand-wash only”  
label.  
For best results, use special detergents and do not  
exceed 1,5 kg of laundry.  
Silk: use special wash cycle 10 to wash all silk garments.  
We recommend the use of special detergent which has  
been designed to wash delicate clothes.  
!Do not pour detergent into the middle compartment (*).  
Detergent should only be poured into the compartment 1.  
compartment 1: Detergent for the wash cycle (powder  
or liquid)  
Curtains: fold curtains and place them in a pillow case  
or mesh bag. Use wash cycle 10.  
For best results liquid detergent should be poured in  
the dispenser immediately before the start of the pro-  
gramme.  
compartment 2: Additives (fabric softeners, etc.)  
The fabric softener should not overflow the grid.  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations  
and to distribute the load in a uniform manner, the drum  
rotates continuously at a speed which is slightly greater  
than the washing rotation speed. If, after several at-  
tempts, the load is not balanced correctly, the machine  
spins at a reduced spin speed. If the load is excessively  
unbalanced, the Washer-dryer performs the distribution  
process instead of spinning. To encourage improved load  
distribution and balance, we recommend small and large  
garments are mixed in the load.  
Preparing the laundry  
Divide the laundry according to:  
- the type of fabric/the symbol on the label  
- the colours: separate coloured garments from whi-  
tes.  
Empty all garment pockets and check the buttons.  
Do not exceed the listed values, which refer to the  
weight of the laundry when dry:  
Durable fabrics: max. 7 kg  
Synthetic fabrics: max. 3 kg  
Delicate fabrics: max. 2 kg  
Wool: max. 1,5 kg  
Silk: max. 1 kg  
How much does your laundry weigh?  
1 sheet 400-500 g  
1 pillow case 150-200 g  
1 tablecloth 400-500 g  
1 bathrobe 900-1200 g  
1 towel 150-250 g  
10  
 
Precautions and tips  
Do not use the appliance to dry foam rubber or  
similar elastomers.  
Make sure that the water tap is turned on during  
the drying cycles.  
! This Washer-dryer was designed and constructed in  
accordance with international safety regulations. The  
following information is provided for safety reasons and  
must therefore be read carefully.  
GB  
Disposal  
General safety  
Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
The European Directive 2002/96/EC on Waste  
Electrical and Electronic Equipment, requires  
that old household electrical appliances must not  
be disposed of in the normal unsorted municipal  
waste stream. Old appliances must be collected  
separately in order to optimise the recovery and  
recycling of the materials they contain and reduce  
the impact on human health and the environment.  
The crossed out “wheeled bin” symbol on the  
product reminds you of your obligation, that when  
you dispose of the appliance it must be separately  
collected. Consumers should contact their local  
authority or retailer for information concerning  
the correct disposal of their old appliance.  
This appliance was designed for domestic use only.  
Thisapplianceisnotintendedforusebypersons(including  
children)withreducedphysical,sensoryormentalcapabilities,  
orlackofexperienceandknowledge,unlesstheyhavebeen  
givensupervisionorinstructionconcerninguseoftheapplian-  
cebyapersonresponsiblefortheirsafety.Childrenshouldbe  
supervisedtoensurethattheydonotplaywiththeappliance.  
- Do not dry unwashed items in the tumble dryer.  
- Items that have been soiled with substances such  
as cooking oil, acetone, alcohol, petrol, kerosene, spot  
removers, turpentine, waxes and wax removers should  
be washed in hot water with an extra amount of de-  
tergent before being dried in the tumble dryer.  
- Items such as foam rubber (latex foam), shower  
caps, waterproof textiles, rubber backed articles and  
clothes or pillows fitted with foam rubber pads should  
not be dried in the tumble dryer.  
- Fabric softeners, or similar products, should be  
used as specified by the fabric softener instructions.  
- The final part of a tumble dryer cycle occurs without  
heat (cool down cycle) to ensure that the items are  
left at a temperature that ensures that the items will  
not be damaged.  
WARNING: Never stop a tumble dryer before the end  
of the drying cycle unless all items are quickly removed  
and spread out so that the heat is dissipated.  
Do not touch the machine when barefoot or with wet  
or damp hands or feet.  
Do not pull on the power supply cable when unplugging the  
appliance from the electricity socket. Hold the plug and pull.  
Do not open the detergent dispenser drawer while the  
machine is in operation.  
Do not touch the drained water as it may reach extre-  
mely high temperatures.  
Never force the porthole door. This could damage the safety  
lock mechanism designed to prevent accidental opening.  
If the appliance breaks down, do not under any cir-  
cumstances access the internal mechanisms in an  
attempt to repair it yourself.  
Always keep children well away from the appliance  
while it is operating.  
The door can become quite hot during the wash cycle.  
If the appliance has to be moved, work in a group of two  
or three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
Before loading laundry into the Washer-dryer, make  
sure the drum is empty.  
During the drying phase, the door tends to get quite hot.  
Do not use the appliance to dry clothes that have  
been washed with flammable solvents (e.g.  
trichlorethylene).  
11  
 
Care and maintenance  
To access the pre-chamber:  
Cutting off the water and electricity sup-  
plies  
GB  
1. using a screwdriver,  
remove the cover panel  
on the lower front part of  
the washing machine (see  
figure);  
Turn off the water tap after every wash cycle. This  
will limit wear on the hydraulic system inside the  
Washer-dryer and help to prevent leaks.  
Unplug the Washer-dryer when cleaning it and during  
all maintenance work.  
Cleaning the Washer-dryer  
2. unscrew the lid by rota-  
ting it anti-clockwise(see  
figure): a little water may  
trickle out. This is per-  
fectly normal;  
The outer parts and rubber components of the ap-  
pliance can be cleaned using a soft cloth soaked in lu-  
kewarm soapy water. Do not use solvents or abrasives.  
Cleaning the detergent dispenser drawer  
Remove the dispenser  
by raising it and pulling it  
1
out (see figure).  
Wash it under running  
water; this operation  
should be repeated fre-  
quently.  
3. clean the inside thoroughly;  
4. screw the lid back on;  
5. reposition the panel, making sure the hooks are secu-  
rely in place before you push it onto the appliance.  
2
Checking the water inlet hose  
Caring for the door and drum of your ap-  
pliance  
Check the inlet hose at least once a year. If there are  
any cracks, it should be replaced immediately: during the  
wash cycles, water pressure is very strong and a cra-  
cked hose could easily split open.  
Always leave the porthole door ajar in order to pre-  
vent unpleasant odours from forming.  
! Never use second-hand hoses.  
Cleaning the pump  
The Washer-dryer is fitted with a self-cleaning pump  
which does not require any maintenance. Sometimes,  
small items (such as coins or buttons) may fall into the  
pre-chamber which protects the pump, situated in its  
bottom part.  
! Make sure the wash cycle has finished and unplug  
the appliance.  
12  
 
Troubleshooting  
Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure  
that the problem cannot be solved easily using the following list.  
GB  
Problem:  
The machine does not switch on.  
Possible causes / Solutions:  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• The ‘DELAY TIMER’ has been selected.  
The machine does not dry.  
• Check the 2 sections above.  
• The ‘DRY’ selector knob is in the  
position.  
The clothes are too hot when the  
drying cycle is finished.  
• A cooling-down period is always added to the end of each drying cycle. If  
the clothes appear too hot to handle leave the door open to allow to cool  
further before removing from the machine.  
The machine does not fill with water or  
the indicator light for the first wash  
cycle stage flashes rapidly.  
• The water inlet hose is kinked.  
• The water inlet hose is not connected to the water supply.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with  
water and continually drains away  
or Water left in the drum  
• The top of the drain hose is too low - It must be fitted at a height between  
65 and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to  
run into the machine, the drain hose must be positioned higher than the  
bottom of the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
or Stuck on wash.  
The machine does not drain or spin  
(error lights flashing).  
• The Pump filter is blocked - (see Care & Maintenance).  
• The drain hose is kinked.  
• New Installation - The blanking cap or spigot has not been removed if con-  
nected under a sink.  
• The drain hose or sink trap is blocked.  
The wash programme takes too long.  
• Programme times will vary due to water pressure, the incoming water temperatu-  
re and if the wash load goes out of balance. This will increase the programme time  
accordingly (see ‘The machine wont spin properly’ below) - (Most Common Cause!).  
The machine vibrates a lot during the  
spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
• New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• Theloadisinaslightoutofbalanceconditionandmachineisspinning,butatalowerspeed.  
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the  
load required before the machine will go into higher spin speeds - This will  
increase the programme time accordingly. This is a safety feature to pre-  
vent damage. Out of Balance can be caused by washing a single heavy item  
(eg duvet, quilt, etc). - Try the programme again using a different load.  
13  
 
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the  
tap on the water supply pipe slightly and try again.  
GB  
• The machine is tilting forwards - It must be level when in its final position.  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the  
fill hose is missing the rubber washer.  
The machine leaks (other than dispenser).  
• The drain hose is not fixed in properly.  
The ‘START/PAUSE’ indicator light  
illuminates Orange and the function  
indicator lights flash rapidly.  
• Switch off the machine and unplug it, wait for approximately 1 minute and  
then switch it back on again If the problem persists contact the Technical  
Assistance Service.  
The machine smells.  
• The machine requires a service wash. Run a 90 degree wash cycle with de-  
tergent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly  
after the program has finished.  
• If there is no power to the machine you need to perform the manual unlo-  
cking procedure (see Precautions & Tips).  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when the  
machine is washing.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
• Too much detergent was used - less detergent is required in soft water.  
After completing the programme, or  
before starting a programme, the ma-  
chine has turned itself off (no lights).  
• To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to acti-  
vate the machine, it can then either be switched off or a new programme  
selected.  
General.  
• Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-  
gress).  
Normally, if your machine successfully completes the cycle, there is unlikely  
to be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label,or wash items that are not intended as machine washable.  
14  
 
Assistance  
Guarantee  
GB  
12 Months Parts and Labour Guarantee  
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown  
repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective  
because of either workmanship or materials, we will, at our discretion, either repair or replace the  
appliance at no cost to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
-
-
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-  
DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There  
will be a charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply  
call our registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense  
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint  
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or,  
where necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will  
replace your machine or, if you prefer, give you your money back.  
15  
 
195108581.00  
11/2012  
-
Xerox Fabriano  
After Sales Service  
GB  
No one is better placed to care for your Hotpoint appliance during the course of its working life than  
us - the manufacturer.  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and  
1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts  
guarantee you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right  
to use quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,  
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts  
separately to ensure that the appliance can no longer be plugged into a mains socket, and the door  
cannot be locked shut.  
16  
 

Graco Inc Paint Sprayer 231 353 User Manual
Graco Plumbing Product 119577 User Manual
Grizzly Grinder G9717 User Manual
Grizzly Lawn Sweeper T10043 User Manual
Hasselblad Camera Lens HC Macro 4 120 User Manual
Honeywell Thermostat CM61NG User Manual
HP Hewlett Packard Cassette Player 1760 User Manual
HP Hewlett Packard Digital Camera R930 User Manual
IBM Universal Remote Version 4 User Manual
IKEA Cooktop ICR416RB01 User Manual