Hotpoint Washer Dryer AQLF9F 49 U User Manual

Instructions for

installation and use

WASHING MACHINE

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

English,1

Description of the machine, 6-7

Control panel

Auto Dose System, 8-9

Running a wash cycle, 10

Wash cycles and options, 11

Table of wash cycles

Wash options

Detergents and laundry, 12

Detergent

Preparing the laundry

AQUALTIS

Washing recommendations

Load balancing system

AQLF9F 49 U

Precautions and advice, 13

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 14

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 15-16-17

Assistance, 18-19

Connecting the drain hose

• the supply voltage is included within the values i

ndicated on the Technical details table (see page 5);

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

• the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

65 - 100 cm

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate

use. Before using the appliance please read the

instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

The drain hose may be

connected to an under-

sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of the

plug. Replacements can be obtained directly from your

nearest Service Depot.

If it is place over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable

plug bearing the BSI mark of approval.

or:

! We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more than

15cms (6 inches). If the hose is pushed down too far,

this may cause the machine to self -syphon ie.

continuously empty as it is filling.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally

inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

Green & Yellow Earth

Blue

Neutral

Live

Brown

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance's

maximum power load indicated in the Technical details

table (see page 5);

As the colours of the wires in the lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured

Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted with

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt about the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE

NEUTRAL (N)

LIVE (L)

BROWN

GREEN & YELLOW

EARTH (E)

GREEN &

YELLOW

13 ampere fuse

BROWN

BLUE

CROSS-BAR

CORD GRIP

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the

plug body and dispose of it as described above.

! The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave it

exposed to rain and thunderstorms.

! When the washing machine is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by an

authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

Technical data

Model

AQLF9F 49 U

width 59.5 cm

height 85 cm

depth 64,5 cm

Dimensions

Capacity

from 1 to 9 kg

Electrical

please refer to the technical data

plate fixed to the machine

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Water connections

Spin speed

up to 1400 rotations per minute

Energy rated

programmes

according to

regulation

programme

and 40°C.

; temperature 60°C

2010/1061

This appliance conforms to the

following EC Directives:

- 2004/108/EC (Electromagnetic

Compatibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

PORTHOLE DOOR

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

Always use the handle to

open the porthole door (see

figure).

activity is detected. Press the ON-OFF

button briefly

and wait for the machine to start up again.

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside the

machine and can be

accessed by opening the

door.

Refer to the chapter "Auto

Dose System" for information

on operation.

TEMPERATURE/

DETERGENT

display

Control panel

DELAY TIMER/SOFTENER /

CYCLE DURATION display

WASH

CYCLE

PHASE

icons

SPIN display

DETERGENT

DILUTION

button

SOFTENER

button

ECO indicator light

START/PAUSE

button with indicator

DETERGENT

button

OPTION button

with indicator light

WASH CYCLE

SELECTOR knob

light

CHILD LOCK button

ON/OFF button with

DELAY

TIMER

TEMPERATURE button

with indicator light

indicator light

DOOR LOCKED

button

indicator light

SPIN SPEED

button

WASH CYCLE PHASE icons: these illuminate to

Button with

ON/OFF indicator light: press this briefly

indicate the progress of the wash cycle (Wash

–

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off

the washing machine during the wash cycle, press and

hold the button for approximately 3 seconds; if the

button is pressed briefly or accidentally the machine will

not switch off. If the machine is switched off during a

wash cycle, this wash cycle will be cancelled.

Rinse

– Spin

– Drain

The text

lights up when the cycle is complete.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To pause

the wash cycle, press the button again; the indicator

light will flash in an orange colour. If the “Door locked”

indicator light is switched off, the door may be

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the “Table of wash cycles”.

opened. To start the wash cycle from the point at which

it was interrupted, press the button again.

The knob will not move during the wash cycle.

TEMPERATURE

button: press to modify or exclude

DOOR LOCKED

indicator light: indicates that the

the temperature setting; the value selected will appear

porthole door is locked. To open the door, pause the

on the display above (see “Running a wash cycle”).

wash cycle (see “Running a wash cycle”).

SPIN SPEED CYCLE

button: press to modify or

CHILD LOCK

button with indicator light: to activate

exclude the spin cycle; the value selected will appear on

or deactivate the CHILD LOCK, press and hold the

button for approximately 2 seconds. when the indicator

light is illuminated, the control panel is locked. This

means it is possible to prevent wash cycles from being

modified accidentally, especially where there are children

in the home.

the display above (see “Running a wash cycle”).

DELAY TIMER

button: press to set a DELAY TIMER

for the selected wash cycle; the set delay time will appear

on the display above (see “Running a wash cycle”).

DETERGENT and

SOFTENER buttons: refer to

"Modifying pre-set parameters" in the chapter "Auto Dose

System".

ECO indicator light: the

icon lights up when, after

altering the washing parameters, an energy saving of at

least 10% is made. Furthermore, before the machine

enters “Standby” mode, the icon will light up for a few

seconds; when the machine is switched off the

DETERGENT DILUTION button: refer to "Filling the

tanks" in the chapter "Auto Dose System".

OPTION button with indicator light: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see “Running a wash cycle”).

estimated energy saving will be around the 80% mark.

Auto Dose System

Introduction

Filling the tanks:

This washing machine is

Open the detergent dispenser drawer in the "Auto Dose

System" mode (refer to "Detergent dispenser").

Slowly pour the detergent (B) and fabric softener (C)

until the tanks are completely filled (see picture).

equipped with two tanks: one

for liquid detergent (either

concentrated or diluted) with

a capacity of approx. 5.5 l

and another for liquid fabric

softener (either concentrated

or diluted) with a capacity of

approx. 3.5 l (see picture).

! Check the detergent/fabric

softener box to verify whether

it is diluted or concentrated

detergent. The automatic

dosing system intakes the

correct amount of detergent and fabric softener from the

tanks for each type of load and at the right time,

guaranteeing optimal washing results without wastage.

The amount of detergent/fabric softener can be modified

manually by pressing the DETERGENT and FABRIC

SOFTENER buttons (refer to "Modifying pre-set

To avoid exceeding the maximum capacity, a buzzer (beep)

will sound with growing intensity to signal the level and 3

long beeps will sound once the tank is completely full.

Start the wash cycle immediately after filling the tanks to

ensure that the dispenser is properly cleaned.The

parameters"). If you prefer, the washing machine can

also be used in the "traditional" mode, i.e. by adding the

detergent in the dispenser; the machine will automatically

detect the detergent and will not use the tanks.

respective icons

(for the detergent) and

(for the

fabric softener) will light up gradually to signal the level.

Detergent dispenser

"Traditional" mode.

Pull out the detergent dispenser drawer up to the first

stop point to add the detergent (either liquid or powder

detergent), bleach or other additives (e.g. whiteners) and

the pre-wash detergent for washing in the "traditional"

mode (refer to "Traditional” mode).

The filling time depends on the density of the product.

Very dense products will take longer to fill.

"Auto Dose System” mode.

In order to fill the detergent

and fabric softener tanks,

Close the detergent dispenser drawer only once the

compartments are completely empty.

the detergent dispenser

drawer must be fully

extracted: open the dispenser

Select the density of the detergent added (either

concentrated or liquid) by pressing the appropriate

button

drawer up to the first stop

point then press the lever (A)

The machine will store the selection.

If no option is selected, the detergent intake option will

be pre-set to "diluted".

and open up to the second

stop point, making sure that

it is fully extracted. Avoid

Use button to set the amount of fabric softener that

will be automatically extracted by the machine:

moving the dispenser drawer during filling operations.

Once the tanks have been filled (refer to "Filling the tanks"),

the machine can run up to 40 cycles before the detergent

finishes (*).

1) If concentrated softener is used, we recommend

selecting the first level ( with one bar) and, if

necessary, stepping up by a single position ( with 2

bars) to increase detergent intake.

First-time use

2) If diluted softener is used, we recommend setting level

Turn the washing machine on by pressing the ON/OFF

button. The first wash cycle must be carried out without

laundry and by adding detergent in the detergent

dispenser (refer to "Traditional” mode); set the

programme " " (Cotton 90°) without pre-wash and

without filling the tanks.

3 ( with 3 bars) and to then either increase/decrease

the amount of fabric softener to be extracted.

3) To exclude the use of fabric softener, press

until

the bars disappear (also refer to "Modifying pre-set

parameters").

(*) with an average load of 4 kg, 40°C Cotton programme, "medium" water

hardness level and dirt level set to 3.

Signals for successive refilling:

Automatic cleaning:

When the level of detergent/fabric softener falls below the

required level, at the end of the cycle, the first segment of

The washing machine carries out an automatic cleaning

cycle during the rinse cycle if the level of detergent that

remains is insufficient for carrying out a

successive wash cycle.

the detergent symbol or the petal of the

fabric

softener symbol in the bottom left section, will flash slowly

on the display. Once the detergent/fabric softener is

finished, the first segment of the detergent symbol or the

Cleaning cycle set by the user:

Run the cleaning cycle (with empty drum) if you require

adding a different product to the previous one or if the tanks

have been incorrectly filled (e.g. fabric softener has been

erroneously poured into the detergent tank or vice-versa).

petal of the

fabric softener symbol in the lower left

section will flash fast to signal that the detergent or fabric

softener tank is empty. While the cycle runs, with empty

tanks, the

cycle or during the pause mode, the first segment of the

symbol and the petal of the symbol in the lower left

symbols will disappear; at the end of the

Press button

cleaning of the detergent tank, button

fabric softener tank or button for cleaning both tanks.

Once the buzzers with growing intensity are followed by 2

long buzzers and the icons for the detergent, for the

fabric softener, for both tanks appear, the cleaning cycle

and hold for approximately 8 sec. to activate

for cleaning the

section will flash fast. If the tanks are not filled, the

successive wash cycles in Auto Dose System will be

carried out without any intake of detergent.

! We suggest adding detergent and fabric softener ONLY

after the machine's signal.

for the selected container will start.

The cleaning cycle lasts about 40' if the tanks are initially

empty; if not, the cycle will last longer.

! NEVER mix two different detergents; always clean out

the tank before adding a new type of detergent (refer to

"Cleaning cycle set by the user").

! During the tank cleaning cycle, the symbol will fill

gradually from bottom to top and the

gradually petal by petal.

symbol will fill

Using the "Auto Dose System"

If the compartments have been filled with detergent and

fabric softener, you may start using the machine (refer to

"Running a wash cycle").

"Traditional" mode

Pull out the detergent dispenser drawer up to the first

stop point (see picture) then pour the amount of

detergent and other additives (e.g. bleach) required for a

single wash cycle directly into the dispenser.

1. pre-wash compartment:

Powder detergents for pre-washing and powder additives

may only be used in the traditional mode or using the "Auto

Dose System", by placing the additives directly inside the

drum, preferably in conjunction with the "laundry ball".

use powder detergent only.

Modifying pre-set parameters:

2. main wash

compartment: use powder

The machine automatically intakes detergent on the

basis of the selected programme, wash load and water

hardness. However, the amount of detergent/fabric

softener used may be modified.

or liquid detergent. If the

latter is used, we

recommend pouring it into

the dispenser immediately

button: press to increase, decrease and to exclude

detergent intake.

before starting the washing

machine and without

running a pre-wash cycle.

3. ! Do not pour anything in this compartment.

Tablet detergent or the relative "laundry ball" must be

added directly inside the drum. In this event, deactivate

button: press to increase, decrease and to exclude

fabric softener intake.

the "Auto Dose System" (by pressing the

button until

the relative vertical bars disappear from the display).

Do not pour any fabric softener as the appropriate

quantity required for each wash cycle will be

automatically extracted.

The level of detergent/fabric softener suggested by the

machine is indicated by 3 bars.

To deactivate fabric softener intake, press the

until the vertical bars disappear from the display.

For wool and silk garments, we recommend using a

special detergent which must be poured directly into the

detergent dispenser (compartment 2).

button

Less than 3 bars indicates a lower level of detergent/

fabric softener compared to that suggested by the

machine, while more than 3 bars indicates a higher level

of detergent/fabric softener.

Cleaning the tanks:

Running the wash cycle:

Select the programme and the compatible options on

the basis of the required need and type of load.

Tank cleaning cycles can either be automatic or pre-set

by the user.

Running a wash cycle

WARNING: before you use the washing machine for

the first time, run a wash cycle with detergent and no

laundry, using the 90° cottons cycle without pre-wash.

press the button until the display shows the text OFF;

the symbol will disappear.

! Once the START/PAUSE button has been pressed,

the time delay may only be decreased.

1. SWITCH THE MACHINE ON. Press the

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the button will then

button.

Modify the cycle settings.

Press the OPTION button to customise the wash

cycle in accordance with your own requirements.

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

• Press the button to activate the option; the

corresponding indicator light will switch on.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

3. MEASURE OUT THE DETERGENT. There is no

need to add detergent when the "Auto Dose System"

mode is used, as the machine automatically intakes

detergent on the basis of the selected programme,

type of load and water hardness. Refer to the

paragraph "Traditional” mode for implementing the

traditional operation mode.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the

DOOR LOCKED indicator light

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress. To change a

wash cycle once it has already started, pause the

washing machine by pressing the START/PAUSE

button; then select the desired cycle and press the

START/PAUSE button again. To open the door during

a wash cycle, press the START/PAUSE button; if the

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH

CYCLE SELECTOR KNOB right or left, until you have

selected the desired wash cycle. A temperature and

spin speed is set for each wash cycle; these may be

adjusted.

6. CUSTOMISE THE WASH CYCLE. Use the

DOOR LOCKED

indicator light is switched off you

relevant buttons on the control panel:

may open the door. Press the START/PAUSE button

again to restart the wash cycle from the point at

which it was interrupted.

Modify the temperature and/or spin

speed.

The machine automatically displays the maximum

temperature and spin speed values set for the

selected cycle, or the most recently-used settings if

they are compatible with the selected cycle. The

temperature can be decreased by pressing the

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may

be opened immediately. If the START/PAUSE indicator

light is flashing, press the button to end the cycle.

Open the door, unload the laundry and switch off the

machine.

button, until the cold wash (

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

). If these buttons are pressed again, the

) setting is reached.

! If you wish to cancel a cycle which has already begun,

press and hold the

button until the cycle stops and

(

the machine switches off.

maximum values are restored.

! Exception: if the “Cotton” programme is selected,

the temperature can be increased up to a value of

90°C.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to

wash even the most valuable and delicate garments in

complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you

wash quilts and padded items with an outer layer made

using synthetic material.

Set a DELAY TIMER.

Press the button until you have reached the desired

delay time. During the setting process, the delay time

is shown on the display and the

symbol flashes.

After selecting a DELAY TIMER time, the fixed

symbol and the cycle duration will appear on the

display. Press the button once to display the selected

delay time. To remove the DELAY TIMER option,

Wash cycles and options

Table of wash cycles

Detergent and additives

Max. Max.

temp. speed

Max.

load

(kg)

Cycle

duration

Icon Description of the wash cycle

Detergent Detergent Fabric

for prewash for wash softener

(°C)

(rpm)

Cottons wash cycles

Cotton with pre-wash

(Add detergent to the relevant compartment).

90°

1400

60°

(Max. 90°)

Cotton (1-2): heavily soiled whites and resistant colours.

Cotton (2): Lightly soiled whites and delicate colours.

Coloured Cotton (3)

40°

1400

600

Shirts

Jeans

800

Special programmes

Baby: heavily soiled delicate colours

Durable Synthetics

40°

60°

40°

60°

30°

40°

800

1400

1200

Durable Synthetics (4)

Delicate Synthetics

"Bed & Bath" for bedlinen and towels.

Duvets: for down-stuffed garments.

Silk: for garments in silk and viscose, lingerie.

Wool: for wool, cashmere, etc.

3,5

800

Mix 30': to refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand)

30°

800

3,5

Partials wash cycles

Rinse

Spin

1400

Drain

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this

value will then be shown on the display.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water

temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

For all Test Institutes:

1) Test wash cycle in compliance with regulation 2010/1061: set wash cycle

with a temperature of 60°C e 40°C.

2) Long wash cycle for cottons: set wash cycle

3) Short wash cycle for cottons: set wash cycle

with a temperature of 40°C.

4) Long wash cycle for synthetics: set wash cycle ; with a temperature of 40°C.

Eco Option

The Eco Option saves energy by not heating the water

Wash options

used to wash your laundry – an advantage both to the

environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage

of a liquid detergent.

Detergent dosage

To dose the amount of detergent (refer to the chapter

"Auto Dose System").

Concentrated Detergent

To modify the degree of detergent density (refer to the

chapter "Auto Dose System").

! It cannot be used in conjunction with

Fabric softener dosage

To dose the amount of fabric softener (refer to the

chapter "Auto Dose System").

Detergents and laundry

Detergent

bacteria by using a greater quantity of water and

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Whenever the detergent and fabric softener “Auto Dose

System” is activated, this washing machine helps to

prevent wastage and to protect the environment,

besides guaranteeing optimal washing performance.

We recommend the following:

optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle,

the machine will slowly rotate the drum; to end the cycle

press the START/PAUSE button.

Silk: use the special “Silk”

wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the “Silk” wash cycle. These should

be folded and placed inside the bag provided.

• Use powder detergent for carrying out a pre-wash

and pour in the "traditional" mode.

• Use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

Wool: Hotpoint is the only washing machine brand to

have been awarded the prestigious Woolmark Platinum

Care endorsement (M.0508) by the Woolmark Company,

which means that all woollen garments may be washed

in the washing machine, even those which state “hand

• When activating the "Auto Dose System" mode, use

liquid detergent and fabric softeners only. Never add

ultra-concentrated detergents (e.g. "Gel" type

detergents or similar).

wash only”

on the label. The “Wool” wash cycle can

be used to wash all woollen garments in the washing

machine while guaranteeing optimum performance.

Duvets: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

• Use gentle liquid detergents for wool and silk

garments and pour in the "traditional" mode.

! Never mix two different detergents; always clean out

the tank before adding a new type of detergent.

special “Duvets”

wash cycle. We recommend that

duvets are placed in the drum with their edges folded

inwards (see figure) and that no more than ¾ of the total

volume of the drum is used.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside the

drum - before the wash cycle begins. In the latter case, it will

not be possible to select the Cottons with pre-wash cycle.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the

machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

Quilts: to wash quilts with a synthetic outer layer, use

the bag provided and set the wash cycle to “Duvets”

Bedlinen and towels: use the “Bed & Bath”

to wash laundry from all over the house; this optimises

cycle

How much does your laundry weigh?

1 sheet

400-500 g

150-200 g

400-500 g

900-1200 g

150-250 g

400-500 g

150-200 g

fabric softener performance and helps you save time and

energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

1 pillowcase

1 tablecloth

1 bathrobe

1 towel

1 pair of jeans

1 shirt

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If

the load is excessively unbalanced, the washing

machine performs the distribution process instead of

spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Washing recommendations

Shirts: use the special “Shirts”

wash cycle to wash

shirts in different fabrics and colours to guarantee they

receive the best possible care.

Jeans: use the special “Jeans”

wash cycle for all

denim garments; turn inside out before washing and use

a liquid detergent.

Baby: use the special “Baby”

wash cycle to remove

the soiling typically caused by babies, while removing all

traces of detergent from nappies in order to prevent the

delicate skin of babies from suffering allergic reactions.

The cycle has been designed to reduce the amount of

Precautions and tips

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Opening the porthole door manually

General safety

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water

using the drain hose,

• This appliance was designed for domestic use only.

• Do not touch the machine when barefoot or with wet

or damp hands or feet.

collecting it in a bucket as

indicated in the figure.

• Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is

freed from its stop position;

pull downwards until you

hear a “click”, which

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

indicates that the door is

now unlocked.

• Always keep children well away from the appliance

while it is operating.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.

5. open the door; if this is

still not possible repeat the

procedure.

• Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Care and maintenance

Cutting off the water and electricity

supplies

To access the pre-chamber:

• Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

• Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

1. take off the cover panel on the front of the machine

by first pressing it in the centre and then pushing

downwards on both sides until you can remove it (see

figures);

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

2. position a container so

that it will collect the water

which flows out

Cleaning the detergent dispenser drawer

(approximately 1.5 l) (see

figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

To pull out the dispenser drawer, open until the first stop

point then press lever A to open completely; finally, press

one of the levers D and pull the drawer outwards (see

picture).

Checking the water inlet hose

Wash it under running water; this procedure should be

effected regularly. Be careful to remove any detergent

residues from the dispenser drawer socket on the

machine.

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

Keep the drawer to the left hand side when replacing it

to ensure that it centres the guides and to prevent it

from jamming.

Caring for your appliance drum

• Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and unplug the

appliance.

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre

(see “Assistance”), make sure that the problem cannot be not solved easily using the following list.

Possible causes/Solution:

Problem

The machine does not switch on.

• The appliance is not plugged into the socket fully, or not enough to

make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

The wash cycle does not start.

• The door is not closed properly.

• The 'ON/OFF' button has not been pressed.

• The 'START/PAUSE' button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• A delayed start has been set.

• The 'CHILD LOCK' is activated (see 'The machine just 'beeps' when a

programme or option is selected' below).

The machine does not fill with

water or Indicator light for the

first wash cycle flashing rapidly.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The 'START/PAUSE' button has not been pressed.

The machine continuously fills

with water and continually

drains away or Water left in the

drum or Stuck on wash.

• The top of the drain hose is too low - It must be fitted at a height

between 65 and 100 cm from the floor.

• The drain hose is connected incorrectly to the sink trap allowing water to

run into the machine, the drain hose must be positioned higher than the

bottom of the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the

standpipe, the 'U' bracket should be fitted 100 mm from the end of

the drain hose.

The machine does not drain or

spin - (error lights flashing).

• The Pump filter is blocked.

• The drain hose is kinked.

• New Installation - The blanking cap or spigot has not been removed

if connected under a sink.

• The drain hose or sink trap is blocked.

The machine does not spin.

• The Spin Speed is set to “

” position.

The machine does not drain or

spin.

• The 'BABY' program has been selected, at the end of the program the

machine drum will rotate slowly. To complete the wash cycle press the

'START/PAUSE'.

• The 'SILK' program is selected, at the end of the program it requires the

drain phase to be started. To complete the program press either the

'START/PAUSE'.

The programme takes too long.

• Programme times will vary due to water pressure, the incoming water

temperature and if the wash load goes out of balance. This will

increase the programme times accordingly (see 'The machine wont

spin properly' below).

• The display time is for guidance only - it is not a precise time to

finish and may vary.

The Display sticks at one 'time to

end' for more than 1 Minute or the

Display changes the estimated 'Time

to End' during the programme.

The machine vibrates a lot

during the spin cycle.

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers,

or the Polystyrene Packaging have not been removed when installing the

machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning,

but at a lower speed.

• There will always be some motor, pump and drum noise during spin.

The machine is noisy.

The machine wont spin properly.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the

load required before the machine will go into higher spin speeds - This will

increase the programme time accordingly. This is a safety feature to

prevent damage. Out of Balance can be caused by washing a single heavy

item (eg duvet, quilt, etc). - Try the programme again using a different load.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down

the tap on the water supply pipe slightly and try again.

The machine leaks from the

dispenser.

• The machine is tilting forwards - It must be level when in its final position.

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or

the fill hose is missing the rubber washer.

The machine leaks (other than

dispenser).

• The drain hose is not fixed in properly.

• Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again If the problem persists contact the

Technical Assistance Service.

The Phase in Progress indicator

lights flash rapidly at the same

time as the ON/OFF indicator light.

• The machine requires a service wash. Run a 90 degree wash cycle with

detergent and no laundry.

The machine smells.

• The door will not open until the door lock indicator light goes out

shortly after the program has finished.

The machine door cannot be

opened.

• If there is no power to the machine you need to perform the manual

unlocking procedure.

• The door seal has drainage holes at the bottom - This is normal.

Door Seal damaged at the

bottom.

• The water level is correct if it can be seen at the bottom of the door.

The water level is too low when

the machine is washing.

• To exit, switch machine off, then press and hold 'ON/OFF' and 'START/

PAUSE' buttons simultaneously for 3 seconds Note the machine will

need the language resetting.

The word 'dON' appears

intermittently in the display

window and the drum slowly turns.

The machine just 'beeps' when a

programme or option is selected

(Child Lock Symbol is lit).

• Deactivate the Child Lock feature by pressing and holding in the 'CHILD

LOCK' button for 2 seconds.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the

text 'for washing machines' or 'hand and machine wash' or the like).

• Too much detergent was used - less detergent is required in soft water.

After completing the

• To comply with new energy saving regulations the machine is fitted

with an automatic standby system. Press 'ON/OFF' button for 3

seconds to activate the machine, it can then either be switched off or

a new programme selected.

programme, or before starting a

programme, the machine has

turned itself off (no lights).

General.

• Your washing machine contains sensors that monitor progress during

the wash cycle (eg: Water Levels, Temperatures, Out of Balance

loads, Wash time/progress). Normally, if your machine successfully

completes the cycle, there is unlikely to be anything wrong!

Troubleshooting:

Possible causes / Solutions:

The machine's washing

performance is unsatisfactory.

• The tanks have not been loaded correctly (e.g. fabric softener has been

added instead of detergent or vice-versa)

• Two different types of detergent/fabric softener have mixed.

! NEVER mix two different detergents; always clean out the tanks before adding

a new type of detergent.

• The "Auto Dose System” is blocked due to prolonged lack of use: carry

out a tank cleaning cycle (refer to "Cleaning cycle pre-set by user").

What happens if the tanks are • Buzzers (Beep) and visual signals (icons appearing on the display) indicate

loaded even if they are already full? that the tank is full. If further detergent/fabric softener is added, the excess

quantity will fall into the drum and will be washed away with the next cycle.

What happens if the dispenser is

used in the traditional mode while

the tanks are still full?

• The machine will automatically track whether powder or liquid detergent

has been loaded in the traditional mode and will not intake any amount of

detergent from the tank. Fabric softener can only be used in the "Auto

Dose System” mode.

Can the tanks also be used for

powder detergent?

• No, powder detergent can only be used in the traditional mode.

Can powder detergent fall into the

tanks?

• No, there is a barrier to prevent powder detergent from falling into one of

the tanks even if the dispenser is open in the "Auto Dose System" position

(i.e. completely open).

What happens if the dispenser is • If the dispenser is not completely open, the detergent or fabric softener

not opened properly when filling the that has been added will fall into the drum and will be washed away with

tanks?

the next cycle.

What happens if detergent and

fabric softener are erroneously

inverted?

• The washing machine will wash with unsatisfactory results, the tanks will

have to be emptied and subjected to a manual cleaning cycle.

What happens if different

detergents are mixed before the

tanks are empty?

• The machine will wash normally although we recommend only refilling the

tanks after the signal emitted by the machine; do not mix different

detergents/fabric softeners.

Remember, you will be charged for a service call for problems caused by incorrect installation,

as listed above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine

washable.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of

breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on

you registering your appliance with us and the parts being fitted by one of our authorised engineers.

There will be a charge for our engineer's time. To activate the extra parts warranty on your

appliance, simply call our registration line on 08448 24 24 24 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the

expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08448 226 226 (Republic of Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone

assistance, or, where necessary, to arrange for an engineer to call. If we cannot resolve the

technical problem we will replace your machine or, if you prefer, give you your money back.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its

working life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the

right to use quality, recycled components to keep down customer costs and minimise material

wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

195093871.00

07/2011

Xerox Fabriano

Hafler Stereo Amplifier DH 200 User Manual
Havis Shields Automobile Accessories C TCB 27 User Manual
Hotpoint Clothes Dryer AQM8D 69 I User Manual
Hotpoint Cooktop 60HGP User Manual
HP Hewlett Packard Network Card zx2000 User Manual
HS Hirschler Automobile PCE1700 User Manual
Hunter Fan Fan 23867 User Manual
IBM Computer Monitor 9511 A User Manual
IBM DVR DM 10 User Manual
Icom Car Amplifier ic pw1 User Manual