Hotpoint Refrigerator RLA32 User Manual

LARDER FRIDGE - MODELS RLA30, RLM30, RLS30, RLA32  
INSTRUCTIONS FOR INSTALLATION & USE  
To ensure that your fridge runs reliably and efficiently follow these steps.  
GETTING STARTED:  
STEP 1  
STEP 2  
Choose a location for your  
fridge, away from any  
heat sources and  
Move the fridge into  
position, using the sides  
of the cabinet. Take care  
to avoid damaging the  
refrigerant circuit pipe  
work on the rear.  
allow adequate  
ventilation - 30mm  
(11/4 inch) gap above.  
STEP 3  
STEP 4  
Before plugging in and  
switching on, leave the  
fridge in its final  
location for at least 15  
minutes to allow it to  
settle.  
Level the fridge by  
adjusting the front feet.  
This will stop rocking or  
vibration and keep the  
door aligned.  
STEP 5  
STEP 6  
Your fridge is now  
working.  
If after 24 hours your  
fridge is not operating as  
you want, refer to the  
Troubleshooting section.  
Plug in and switch on.  
Allow the fridge to cool  
before placing food  
inside.  
All food in the fridge  
should be covered.  
Read the rest of these instructions to get the best from your appliance  
and remember to fill in your guarantee registration.  
 
Keep this Book in a safe place for quick reference.  
Installation  
30mm (11/4 inch)  
Location & Air Circulation  
Locate your fridge away from sources of heat e.g.  
cookers, radiators, direct sunlight as extreme temperature  
will affect its performance.  
1
Allow a minimum 30mm (1 /4 inch) between the top of  
the fridge and the underside of the worktop.  
Providing you follow the recommended ventilation requirements you will :-  
G
G
G
G
Prolong the life of the fridge.  
Minimise the risk of condensation on the outside of the fridge.  
Minimise the running costs.  
Minimise operating sounds caused by vibration.  
Minimum space required to open door  
The fridge needs a space of 600mm (24 inches) in front to allow the door to open.  
1
4
When positioning the fridge next to a unit, a gap of 30mm (1 / inch) can be left  
at the hinge side of the door to allow the easy removal of furniture. If preferred  
the fridge can be positioned so that a gap is not left. This will restrict how far the  
door can be opened but the furniture can still be removed (see diagram below).  
The door hinge side can be changed to make it easier to open (see ‘Door Reversal’  
in the CLEANING & MAINTENANCE section).  
TOP VIEW  
TOP VIEW  
less than 30mm  
30mm or more  
3
 
Installation  
Levelling:  
Level the fridge when it is in its final location by adjusting the front feet, until firm  
contact is made with the floor. This will stop rocking or vibration and keep the door  
aligned which helps the fridge run reliably and efficiently.  
Before plugging in and switching on, leave the fridge standing in its final location for  
at least 15 minutes to allow it to settle.  
Fitting a Fridge under a Work Top  
To minimise running costs Hotpoint recommend fitting a vent to the rear of your  
worktop, which is available from Hotpoint Genuine Parts & Accessories Mail Order  
Hotline (see KEY CONTACTS, back page).  
WARNING: If there is less than 30mm clearance above the fridge, a vent must be  
fitted to provide adequate ventilation above your fridge.  
4
 
Installation  
Electrical Supply  
WARNING: This appliance must be earthed.  
The fridge must be positioned so that the plug is accessible after  
installation.  
Fuses  
Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the  
fuse, only use those rated at 13A and ASTA approved to BS1362.  
Changing the Plug  
Cut off and dispose of the supplied plug if it does not fit your socket.  
WARNING: To avoid a shock hazard do not insert the discarded plug into a socket  
anywhere else.  
IMPORTANT WIRES IN THE MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE  
FOLLOWING CODE :  
Green/Yellow  
Blue  
-
-
Earth  
Neutral  
Brown  
-
Live  
If you change the plug, the colour of wires in the mains lead may not correspond with  
the colour of the markings identifying terminals in the plug. You should therefore  
wire it as shown above.  
Changing the Mains Lead  
This fridge is fitted with a special mains lead. If you need to replace the mains lead  
due to damage or require a longer lead, one can be bought from Hotpoint Service  
(see KEY CONTACTS, back page). It is strongly advised that this work is carried out by  
a qualified electrician.  
CE Marking certifies that this appliance conforms to the following EEC  
directives : Low Voltage Equipment - 72/23/EEC & 93/68 EEC  
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC & 93/68/EEC  
5
 
Controls  
Controlling the Temperature of the Fridge Compartment  
The control wheel on the front of the worktop adjusts the internal fridge  
compartment temperature. The internal temperature should be 5˚C or colder  
although some sections, such as the salad bin, will be slightly warmer.  
The setting of the control wheel will depend on the location of the fridge, the room  
temperature and how often the door is opened. The normal set point (marked by a 3  
and N on the dial) is usually suitable. If you need to adjust the temperature turn the  
control wheel:  
Clockwise (higher number) - Colder  
Anti-clockwise (lower number) - Warmer  
You can check the temperature of the fridge compartment by using a Fridge Freezer  
Thermometer available from Hotpoint Genuine Parts and Accessories Mail Order  
Hotline (see KEY CONTACTS back page).  
WARNING: Do not use a mercury filled thermometer, as breakage would cause a  
health hazard.  
Your fridge must NOT be placed in a room where the temperature goes below 6˚C or  
above 38˚C for prolonged periods, as the internal fridge temperature will not be  
maintained.  
6
 
Useful Advice  
A
B
C
A
B
D
B
Note:  
The Rating Plate, which lists the appliance Model Number and Serial  
Number can be found near the bottom of the left hand internal wall.  
STORAGE ZONES  
Zone Type  
Food Storage  
A
Cool  
Dairy products, Cheese, butter, margarine,  
Low fat spreads, cooking fats / lards  
Preserves - Jam, curd, marmalade,  
spread, salad dressing or sauces.  
B
C
Colder  
General food storage  
Coldest  
Meat fish & poultry  
Pre-cooked / chilled food  
D
Salad  
Bin  
Vegetables, fruit and salad items  
(Not recommended for the storage of  
bananas or onions).  
7
 
Useful Advice  
Making the best use of your Fridge  
To ensure that your fridge operates as efficiently as possible :  
G
Follow food packaging “best before/use by” instructions or your suppliers  
advice on a suitable maximum storage time.  
G
Keep foods covered to retain moisture and prevent flavour/odour  
transference. Plastic bags, aluminium foil, plastic stretch wrap and containers  
with lids are ideal.  
G
G
Avoid opening the doors unnecessarily or for longer than needed.  
Allow hot or warm food to cool down in covered containers before placing in  
fridge, as placing hot food inside reduces efficiency.  
Storing Food in a Fridge  
G
Pack and store cooked and fresh food separately.  
G
Wrap raw or defrosting meat and poultry in polythene or foil and store  
below cooked foods and dairy products to avoid contamination of dripping  
food juices.  
G
Wrap cheese in greaseproof paper and place in an airtight container or  
polythene bag.  
Bring to room temperature before consuming.  
Empty left over canned food into a covered storage containers before  
placing in the fridge.  
Position food to allow cold air to circulate freely, ensuring nothing comes  
into contact with the interior back wall of the fridge, or covers the defrost  
gutter drain hole below this.  
G
G
G
Use the different storage zones inside your fridge compartment to store a  
wide variety of food items.  
(Models RLM30 and RLS30 only):  
Microban® is a unique antibacterial technology which is built into interior  
components of your fridge during manufacture. Microban® protects against growth  
of potentially harmful and odour causing bacteria on the interior fridge surfaces,  
thereby keeping your fridge fresher and more hygienically clean during use.  
Microban® will not wash out or wear out and will provide continuous protection  
against bacteria for the life of your fridge. Microban® technology has been proven  
safe, durable and effective over many years of use in personal care and household  
consumer products. In addition, Hotpoint operate a rigorous antibacterial testing  
programme through approved independent testing laboratories.  
Note : You should continue to clean your fridge as recommended (see CLEANING  
& MAINTENANCE section). Microban® provides an extra level of hygiene  
protection in your fridge in between cleanings.  
8
 
Useful Advice  
Advice on Adjusting Shelves  
Make the most of the interior storage  
space by repositioning shelves to suit the  
various heights of individual items you  
wish to store.  
To remove, ensure that the door is open fully.  
Slide the shelf forward and tilt from position.  
Split glass shelf  
The split shelf can be used as a standard shelf but also as  
two half shelves.  
The front half can be repositioned above or below to  
enable storage of larger items.  
Note : Only the front half of the  
shelf can be repositioned, the back  
half must remain in its original  
position.  
Salad Bins  
For the storage of fruit, vegetables and salad items.  
When storing vegetables, remove unusable leaves and soil and leave lettuce, cabbage  
and cauliflower on the stem.  
It is advisable to clean the salad bin regularly, it can be removed by sliding it out from  
position.  
Note : Care must be taken to ensure that the salad bin is closed before  
shutting the fridge door.  
Commodity and Bottle Racks  
Commodity racks can be repositioned in the door to suit your storage requirements.  
The lidded commodity rack is recommended for the storage of dairy items, such as  
butter, margarine and cheese.  
To remove, lift rack vertically to release from fixing supports.  
To replace, align grooves on either side of the rack above fixing supports and push  
down until secure.  
In order to get the best results from the bottle retainer it is advised that it be  
positioned centrally on the bottle rack.  
Egg Rack  
The egg rack can be used in conjunction with any commodity rack and is easily  
removed for cleaning.  
Note: Wipe, don’t wash eggs.  
9
 
Defrosting and Cleaning  
No manual defrosting required  
The fridge compartment will defrost automatically. During defrost periods water  
droplets form on the interior back wall of your Larder Fridge and refreeze afterwards.  
Note : if your kitchen becomes exceptionally warm, your Larder Fridge may not  
defrost regularly.  
WARNING: Ensure the defrost drain hole is kept clear and that stored food does  
not come into contact with the interior back wall of your Larder Fridge.  
Cleaning  
WARNING: Switch off electrical supply and pull out mains plug before cleaning.  
Interior  
1.  
Remove food and wrap or cover to keep it cool.  
2.  
Remove salad bins, racks and shelves from the fridge compartment and wash  
in warm water and washing up liquid using a soft cloth, dry thoroughly.  
Note : It is important to ensure that cleaned shelves, baskets and bins are  
thoroughly dried before refitting to the fridge compartment.  
3.  
Wipe interior and fitting with a clean cloth wrung out in a solution of either  
one teaspoon of bicarbonate of soda to one pint of water or Milton™  
sterilising fluid, diluted according to the manufacturer’s instructions.  
Dry interior thoroughly with a clean cloth before replacing fittings and food.  
4.  
Exterior  
Use a clean soft cloth wrung out in warm water and washing up liquid to wipe the  
exterior surface, dry thoroughly.  
WARNING: Do not use abrasive powder, household cleaner, bleach or wax polish  
to clean your fridge, they leave a smell in the fridge and can damage the exterior.  
Use a soft brush or vacuum cleaner to remove dust from underneath the fridge and  
from the compressor and condenser situated at the back of the fridge.  
WARNING: Do not damage the pipework.  
Door Seal  
Use warm water and a clean soft cloth to wipe along and in between the creases of  
the door seal, dry thoroughly. Take care not to damage the seal and avoid using  
sharp objects.  
WARNING: Do not use detergent, it will damage the seal.  
10  
 
Defrosting and Cleaning  
Going Away  
If you are going away and don’t want to use your fridge, switch off the socket outlet  
and pull out the mains plug. Remove food and follow the cleaning instructions on  
the previous page.  
Note : Leave the door ajar to prevent an accumulation of odours.  
Changing the Light Bulb  
WARNING: Switch off at socket outlet and pull out the mains plug  
Obtain a replacement SES 15W bulb from the Hotpoint Genuine Parts and  
Accessories Mail Order Hotline (see KEY CONTACTS back page) and fit as follows :  
1.  
Remove any shelves from directly below the interior light, to make access  
easier.  
2.  
3.  
4.  
5.  
Squeeze the side of the lamp guard lightly to unclip. Remove and retain.  
Remove old bulb and fit new one.  
Refit lamp guard.  
Plug in and switch on electrical supply.  
11  
 
Maintenance  
You will need a pozi head screwdriver to carry out this procedure.  
Our Service Department can arrange for an Engineer to do the conversion for you but  
a charge will be made.  
Door Reversal  
WARNING: Switch off electrical supply and pull out the mains plug.  
Remove loose items/fittings from inside the fridge and place food into insulated  
containers whilst carrying out this operation.  
1.  
2.  
3.  
4.  
5.  
6.  
Open the door as wide as possible.  
Note : You may require assistance to do this:  
Support the door and using a screwdriver, remove the screw  
securing the top hinge.  
Carefully tilt the door to remove the hinge from the cabinet  
and lift the door off the bottom hinge.  
Remove the spacing washers from the bottom hinge.  
Note : You may require assistance to do this:  
Carefully lay the fridge on its back, onto a suitable protective  
material (ie. the original packaging).  
Remove the foot bracket and the hinge/foot bracket by removing their fixing  
screws.  
hinge / foot  
bracket  
foot bracket  
7.  
Refit the foot bracket and hinge/foot bracket on the opposite sides using  
their fixing screws.  
Note : You may require assistance to do this:  
Carefully lift the fridge upright and replace the spacer washers onto the  
bottom hinge pin.  
Using a thin blunt instrument, remove the hinge  
bush cap from the top left of the door and refit on  
the top right.  
8.  
9.  
10.  
If applicable - using a screwdriver, remove the door  
stop from the bottom right of the door and refit on  
the bottom left.  
door stop  
Note : You may require assistance to do this:  
11.  
12.  
Replace the top hinge onto the door, slide the door onto the bottom hinge  
pin and support the door whilst screwing the top hinge into position. Ensure  
that the top hinge bracket is positioned correctly.  
Adjust the front feet (see ‘Levelling’ SAFETY & INSTALLATION section).  
Note : Let the appliance stand upright in it’s final location for at least 15  
minutes before plugging in and switching on the electricity supply.  
12  
 
Troubleshooting  
IS THE FRIDGE WORKING AS YOU  
WANT?  
The interior light doesn’t work  
WARNING: Switch off the socket outlet  
and pull out the mains plug.  
1. Check bulb is screwed in correctly. If  
still not working then see ‘Changing  
the Light Bulb’ in the CLEANING &  
MAINTENANCE section.  
Have you read through the instruction  
book ?  
If you still have a problem, before calling  
our service organisation see if any of the  
tips below help.  
Ice builds up rapidly inside the fridge  
1. Check that nothing is stopping the  
door from closing properly.  
2. Check that foods and liquids are  
covered to avoid the build up of  
moisture inside.  
The appliance will not work  
1. Check plug is firmly positioned in the  
socket outlet and the power supply is  
switched on.  
2. Check power supply with another  
appliance.  
3. See ‘Defrosting’ in the CLEANING &  
MAINTENANCE section for advice.  
3. Check fuse/circuit breaker.  
4. Check the door is closed properly.  
The appliance is making a lot of noise  
1. Check that the rear pipe work is clear  
of the wall, skirting board and other  
obstacles.  
If there is still a problem contact  
Hotpoint Service (See KEY CONTACTS,  
back page, for contact details).  
2. Check that all feet/wheels are firmly  
in contact with the floor and the  
fridge is level.  
OPERATING SOUNDS OF A FRIDGE  
These are the normal types of sound that  
your fridge will make:  
3. See OPERATING SOUNDS below.  
The temperature is too warm  
1. Turn the control wheel to a higher  
number. See CONTROLS section.  
2. If the appliance is close to a heat  
source, move it to another location.  
3. Check that there is enough  
ventilation around the appliance.  
4. Check that the door has been closed  
properly.  
The fridge motor (compressor) makes a  
buzzing or humming sound when it is  
running. This can be louder when it is  
first switched on. This sound will reduce  
over the first few months.  
Gases flowing through the pipes can  
produce gurgling, bubbling, roaring or  
humming noises.  
The temperature is too cold  
1. Turn the control wheel to a lower  
number. See CONTROLS section.  
The temperature control can make a  
clicking noise when it turns the motor on  
and off.  
There is water beneath the salad bin  
and on the floor  
1. Check defrost gutter drain hole is not  
Expansion and contraction of parts  
inside the fridge can produce a cracking  
noise as they rapidly change  
temperature.  
covered.  
2. Check that nothing has come into  
contact with the interior back wall of  
the fridge.  
13  
 
Hotpoint guarantee  
“Satisfaction guaranteed or your money back”  
We give you a unique ‘satisfaction guaranteed’ promise - valid for 90 days - after you have  
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint  
will arrange for an engineer to call. If the technical problem is not resolved under this  
guarantee, we will replace your machine or, if you prefer, give you your money back.  
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well  
as free replacement parts for the first 5 years (except microwaves, selected integrated  
appliances and cooker hoods, which have a one year guarantee) provided that they are  
fitted by a Hotpoint engineer.  
Guarantee terms and conditions  
Your guarantee is only applicable in the United Kingdom or Republic of Ireland  
and is subject to the following provisions that your appliance:  
G
Has been installed and used correctly in accordance with this instruction booklet.  
G
Has been used solely for domestic purposes and is located on domestic  
premises (ie. not for commercial or trade use).  
G
G
Has been properly connected to a suitable electrical supply voltage as stated on  
the appliance rating plate.  
Has not been subject to misuse, accident, modified or repaired by anyone other  
than a Hotpoint service engineer.  
For pre purchase information on any other Hotpoint product call: 08701 50 60 70  
Recycling & Disposal Information  
As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves  
the right to use quality recycled components to keep down customer costs and minimise  
material wastage.  
Please dispose of packaging and old appliances carefully. Old refrigerant and oil must be  
disposed of in a safe and environmentally friendly manner, using suitably qualified  
personnel.  
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush  
with the appliance. Dispose of these parts separately to ensure that the appliance can no  
longer be plugged into a mains socket, and the door cannot be locked shut.  
14  
 
After Sales Service  
“No company is better positioned to offer an after sales service on a  
Hotpoint appliance than us - the manufacturer”  
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully  
inclusive parts and labour guarantee for the first 12 months. In addition to this you also have  
the advantage of free replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we offer the following after  
sales service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number of your appliance  
(see USEFUL ADVICE SECTION for rating plate position).  
Available 364 days a year with a fast, effective and value for money service. We have the largest  
white goods repair service in the UK with over 1200 of our own fully trained engineers. All  
repairs include a parts and labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your appliance, our operators are on  
hand with help and advice.  
All this ensures that you will receive the best available after sales service possible.  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two  
service cover plans to give you total peace of mind.  
G Repair Protection Plan - FREE service repairs for a single Hotpoint appliance during the  
period of cover.  
G Kitchen Cover  
- FREE service repairs for all your Hotpoint appliances less than 8  
years old.  
Genuine Parts and Accessories  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
A wide range of genuine parts and accessories are available from our hotline or through  
our web site.  
Genuine parts and accessories, extended warranties and service repairs are all  
available on our web-site at:  
15  
 
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have  
complete confidence in both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
See USEFUL ADVICE SECTION for rating plate position  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
General Domestic Appliances Limited, Morley Way, Peterborough, PE2 9JB.  
.
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
May 2003 2766200030 - 01  
 

Graco Baby Accessories 2L03 User Manual
Haier Water Heater FCD JTSA50 III User Manual
HannsG Double Oven HB171 User Manual
Hotpoint Refrigerator HTR18ABR User Manual
HP Hewlett Packard Network Card 3162 User Manual
HP Hewlett Packard Projector HP ep7100 User Manual
Hubbell Stereo System SM 28 User Manual
Hunter Fan Outdoor Ceiling Fan 41462 01 User Manual
Husqvarna Car Seat DS 50 User Manual
iHome Speaker iH20 User Manual