Honeywell Security Camera HD40 User Manual

/
Rev 0 03 18  
P/N:3810-0071G  
USER INFORMATION:  
CAUTION  
Design and specifications  
are subject to change  
without notice.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE  
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.  
SPECIFICATIONS:  
Series  
HD40  
Explanation of two Symbols  
Signal System  
NTSC : 525 Lines  
PAL : 625 Lines  
The lightning flash with arrowhead symbol, within an equilateral  
triangle, is intended to alert the user to the presence of un-insulated  
"dangerous voltage" within the product's enclosure that may be of  
sufficient magnitude to constitute a risk of electric shock to persons.  
Scanning System  
Scanning Frequency (H)  
Scanning Frequency (V)  
Image Sensor  
Total/Effective Pixels No.  
S/N Ratio  
2 : 1 Interlace  
Operation  
Manual  
15.734kHz  
59.94Hz  
1/3 inch SONY Super HAD CCD  
270K/250K 320K/290K  
15.625kHz  
50Hz  
The exclamation point within an equilateral triangle is intended to  
alert the user to the presence of important operating and maintenance-  
(servicing) instructions in the literature accompanying the appliance.  
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM  
OF THE SYSTEM.  
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT  
TO RAIN OR MOISTURE"  
More than 48dB  
380 TV Lines  
1.0 Vp-p (75 Ohms, composite)  
Fixed Lens (f=3.8mm)  
Manual  
• 1/3” SONY Super HAD CCD  
• 380 TV Lines Resolution  
• Built-in Fixed Lens (f=3.8mm)  
• Min. Illumination : 0.1 Lux  
• Auto White Balance  
Resolution  
Video Output Level  
Lens- Mirror Cover  
Focus  
Sync. System  
Sensitivity  
Electronic Shutter  
White Balance  
AGC  
Input/Output Connector  
Power Consumption  
PRECAUTION:  
!
Internal  
0.1 Lux  
All the warnings and instructions of this manual should be followed.  
• Diameter of Bubble : 85mm  
• Easy Install (3-Axis)  
Remove the plug from the outlet before cleaning. Do not use liquid  
1/60~100,000 Sec.  
1/50~100,000 Sec.  
aerosol detergents. Use water damped cloth for cleaning.  
To reduce the risk of fire or electric shock, do not expose this appliance  
to rain or moisture.  
Do not place anything on top of the unit that might spill or fall into it.  
Do not attempt to service this unit yourself as opening or removing  
covers may you to dangerous voltage or other hazards. Please refer  
all servicing to qualified service personnel.  
Auto  
Auto  
Power (Red Jack), Video (Yellow Jack)  
12VDC (10V~15V), 0.15A / 1.8W (Max)  
85mm  
t
READ AND KEEP THIS  
OPERATION MANUAL  
(
)
Ø
Dome Size  
Weight  
Keep enough space around the unit for ventilation.  
Slots and openings on the monitor should not be blocked.  
Approx. 210g  
During flashes of lightning or cracks of thunder, or when the system  
is not used for a long time, unplug the system power supply to  
protect the unit from lightening or power surges.  
Need Help?  
Call 1.800.796.CCTV for sales, service and customer support.  
90º  
INSTALLATION:  
COMPOSITION:  
3
-axis  
Built-in  
camera  
Tilt  
bracket makes it much  
easier to rotate in any  
direction.  
This manual explains the installation and operating method for the  
color dome camera. Before installation, make sure you are familiar  
with this product's special features and proper operating technique.  
360º  
Dome Camera  
Guide Pattern  
Horizontal  
Pan  
360º  
Stick the guide pattern on the wall or ceiling.  
1
Ceiling  
Mounting Screw  
Operation Manual  
Drill two holes according to the guide pattern  
TROUBLESHOOTING:  
2
then insert anchors into the drilled holes.  
Guide Pattern  
If you have trouble operating  
your camera, refer to the following.  
Draw out power/video wires to the connecting  
places.  
CONNECTION:  
3
If the guidelines do not enable you to solve the problem,  
contact an authorized technician.  
Dome Base  
The wire is polarized.  
12VDC Power Type  
Fixed the camera to a celling using two screws.  
4
5
Use 12VDC power source.  
Check the power source for the monitor  
and camera and ensure that the voltage  
and polarity are properly connected and  
being supplied correctly.  
The image does not  
appear on the screen.  
#
1
Video  
(Yellow)  
Video Output  
GND  
Adjust desired focus and scene by turning  
and moving the 3-axis camera bracket by  
hand.  
No. Function Terminal Color  
#1 Video Output Yellow  
Remark  
Mounting  
Screw  
1.0 Vp-p  
Check if the lens is stained. If dirty,  
clean the lens with a soft, clean cloth.  
Adjust the Back Focus of the lens again.  
The image on the  
screen is dim.  
12VDC(10V~15V),  
Put the dome cover over the base.  
Power - 12VDC  
(Red)  
#2 Power Input  
Red  
6
7
1.8W(Max)  
#
2
Fix the dome cover on the base by covering.  
Check if you have connected the camera  
to a proper power source and If there is  
no problem with the power, turn the unit  
off immediately and seek assistance from  
our Customer Service department.  
The camera does not  
work properly, the surface  
of the camera case is hot,  
and a black line appears  
on the screen.  
DIMENSIONS:  
Dome Cover  
4.45”  
(113 mm)  
NOTE  
Check if the camera is pointed toward  
the sun or a fluorescent lamp.  
Adjust the angle or location of the  
camera if too much light is coming into  
the screen.  
The screen blinks a lot.  
Insert coin to the side  
hole and remove the  
dome cover by twist coin.  
3.35”  
(85 mm)  
3.35”  
(85 mm)  
 

Graco Air Conditioner 24R200 User Manual
Graco Stroller 4530 4540 User Manual
Harman Kardon Network Hardware BTA 10 User Manual
Havis Shields Automobile Accessories WGI F14 User Manual
Honeywell Heating System L8124A User Manual
Hotpoint Microwave Oven BD52 BD62 User Manual
HP Hewlett Packard All in One Printer 510PS User Manual
HP Hewlett Packard Welding System SCSI User Manual
Hughes Kettner Stereo Amplifier TrilogyTM User Manual
IKEA Washer FWM5 User Manual