Honeywell Scanner Hyperion 1300 g User Manual

Hyperion 1300g  
Linear Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
한글 www.honeywellaidc.com 로 이동합니다 .  
HP1300-QS Rev A  
12/10  
 
Serial (RS232):  
RS485:  
KeyboardWedge:  
 
Reading Techniques  
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
RS485 Interface  
The RS485 interface defaults to port 5B. If you have an IBM POS  
terminal using port 9B, scan the appropriate code below to program  
the terminal, then power cycle the cash register.  
IBM Port 9B HHBCR-1  
Interface  
IBM Port 9B HHBCR-2  
Interface  
Note: For additional RS485 interface selections, see the User’s  
Guide for your product at our website,  
 
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from the end of this document, then the Save  
bar code to program the keyboard for your country. As a general  
rule, the following characters are not supported by the scanner for  
countries other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~.  
Program Keyboard Country  
Country Code  
Belgium  
Scan Country Code  
Scan  
1
8
2
3
4
7
Italy  
5
Denmark  
Norway  
9
Finland  
Spain  
10  
6
France  
Switzerland  
USA (Default)  
Germany/Austria  
Great Britain  
0
Save  
 
Trigger  
The following bar codes will allow you to use the reader in Manual  
Trigger mode (need to press the trigger to read), Automatic Trigger  
mode (the beam is always on), or Presentation mode (the reader is  
activated when it “sees” a bar code).  
Manual Trigger  
(Default)  
Automatic Trigger  
Presentation Mode  
Reread Delay  
This sets the time period before the scanner can read the same bar  
code a second time. Setting a reread delay protects against  
accidental rereads of the same bar code.  
Medium Reread Delay  
 
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
2
4
6
1
3
5
7
 
8
A
C
E
9
B
D
F
Save  
 
EZConfig  
To access additional features for the scanner use EZConfig, an  
online configuration software tool, available from our website at  
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2010 Honeywell International Inc. All rights reserved.  
 
 

Halo Lighting System Indoor Furnishings CVSAT50 User Manual
Harbor Freight Tools Welder 95028 User Manual
Harman Kardon DVD Player 38 User Manual
Hasbro Robotics 80226 User Manual
Hotpoint Refrigerator FF187E User Manual
Hotpoint Washer WMFUG 842 User Manual
Hunter Fan Home Safety Product 45180 User Manual
Hunter Fan Ventilation Hood 82003 User Manual
Husqvarna Brush Cutter 326RJX Series User Manual
Ikelite Digital Camera MG HD3 User Manual