Honeywell Network Card 800 08115 User Manual

800-08115 1/11 Rev. B  
GSMVLP5 GSM and  
ILP5 Ethernet  
Communications Modules  
Installation and Setup Guide  
Installing Communication Modules  
RF Exposure  
WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of  
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other  
antenna(s) or transmitter.  
Installing the GSMVLP5 in the LYNX Touch Series Control  
Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the  
module in the LYNX Touch.  
1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).  
LYNX TOUCH SERIES  
FCC ID: CFS-8DLLYNXTOUCH1  
IC: 573F-LYNXTOUCH1  
IC MODEL: LYNXTOUCHG1  
CONTAINS TRANSMITTER MODULE  
FCC ID: QIPMC55I  
IC: 7830A-MC55I  
800-08334 2/11 Rev  
A
LYNX TOUCH SERIES  
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY  
CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS  
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST  
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY  
CAUSE UNDESIRED OPERATION.  
COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000  
RINGER EQUIVALENCE: 0.1B  
800-08126 1/11 Rev  
A
5000-100-186-V0  
Figure 1. FCC/IC Label Location  
2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the  
unit with the blade of a medium size screwdriver (Refer to Figure 2).  
3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly  
seated into the receptacle on the control (Refer to Figure 2).  
4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).  
5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.  
Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and  
Setup Guide (P/N 800-06834 or higher).  
 
ETHERNET CABLE  
TO ILP5  
RJ45 RECEPTACLE  
LYNX TOUCH  
REMOVE ILP5  
KNOCKOUT  
REMOVE ILP5  
SPACER  
ALTERNATE INSTALLATION  
ILP5 SPACER  
RJ45  
RECEPTACLE  
CONNECTOR  
BOARD  
ROTATED  
TIE  
WRAP  
180  
(1)  
TIE  
WRAP  
POINT  
CONNECTOR BOARD  
SCREW  
(3)  
ILP5  
RECEPTACLE  
LYNX TOUCH  
LOCKING TABS  
5000-100-154-V1  
Figure 3. Installing the ILP5 in the LYNX Touch  
 
Electrical Specifications  
GSMVLP5  
Voltage Input  
Current  
Idle  
5V  
15 mA, standby  
300mA, average transmit  
1.6A peak transmit, 25% duty cycle  
Average  
Peak  
ILP5  
Voltage Input  
Current:  
5V  
83 mA, 100 Base T with traffic  
41 mA, 10 Base T with traffic  
2 Corporate Center Drive, Suite 100  
P.O. Box 9040, Melville, NY 11747  
Copyright © 2011 Honeywell International Inc.  
Ê800-08115!Š  
800-08115 1/11 Rev. B  
 

Graco Marine Instruments 395 User Manual
Graham Field Personal Lift lf 1031 User Manual
Grizzly Drill H6238 User Manual
Grizzly Impact Driver H8000 User Manual
Haier Dishwasher HDW101SST User Manual
Hamilton Beach Kitchen Grill 31605N User Manual
Harman Kardon Home Theater System AVR 154 User Manual
Heath Zenith Door 598 1224 01 User Manual
Honeywell Oxygen Equipment Y8610U User Manual
HP Hewlett Packard Cable Box 8591C User Manual