Honeywell Barcode Reader VG1200 QS User Manual

Voyager™ 1200g  
Single-Line Laser Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
한글 www.honeywellaidc.com 로 이동합니다 .  
VG1200-QS Rev A  
10/10  
 
Serial (RS232):  
RS485:  
KeyboardWedge:  
 
Reading Techniques  
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
RS485 Interface  
The RS485 interface defaults to port 5B. If you have an IBM POS  
terminal using port 9B, scan the appropriate code below to program  
the terminal, then power cycle the cash register.  
IBM Port 9B HHBCR-1  
Interface  
IBM Port 9B HHBCR-2  
Interface  
Note: For additional RS485 interface selections, see the User’s  
Guide for your product at our website,  
 
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from the end of this document, then the Save  
bar code to program the keyboard for your country. As a general  
rule, the following characters are not supported by the scanner for  
countries other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~.  
Program Keyboard Country  
Country  
Code  
Country  
Scan Code  
Country  
Scan Code  
Scan  
10  
6
Arabia  
Belgium  
China  
91  
1
Hungary  
IBM Financial 90  
19  
Spain  
Switzerland  
Thai  
92  
2
Italy  
5
94  
24  
0
Finland  
France  
Japan  
Korea  
28  
93  
Turkey  
3
USA (Default)  
Germany/  
Austria  
4
7
Russia  
26  
31  
Vietnam  
95  
Great Britain  
Slovenia  
Save  
 
Out-of-Stand Modes/Code Gate® Activation  
When the scanner is in the stand, bar codes are automatically read  
when they are in the scanner’s field of view. When the scanner is out  
of the stand, by default you must push the button on top of the  
scanner to read a bar code. Use the following commands to adjust  
how the scanner behaves when it is out of the stand.  
Presentation Mode Out-of-Stand: When the scanner is not in the  
stand, it automatically detects bar codes, then scans and transmits  
the data. The laser turns off afterward. (If you are accustomed to a  
Voyager 9520, this setting is the same as the 9520’s default.)  
Presentation Mode with CodeGate Out-of-Stand: When the  
scanner is not in the stand, it automatically detects bar codes and  
decodes them. However, the data is not transmitted until you press  
the button. The laser remains on briefly after the transmission. (If  
you are accustomed to a Voyager 9540, this setting is the same as  
the 9540’s default.)  
Presentation Mode  
Out-of-Stand  
Presentation Mode  
with CodeGate  
Out-of-Stand  
Reread Delay  
This sets the time period before the scanner can read the same bar  
code a second time. Setting a reread delay protects against  
accidental rereads of the same bar code.  
Medium Reread Delay  
 
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
2
4
6
1
3
5
7
 
8
A
C
E
9
B
D
F
Save  
 
EZConfig  
To access additional features for the scanner use EZConfig, an  
online configuration software tool, available from our website at  
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2010 Honeywell International Inc. All rights reserved.  
 
 

Grizzly Grinder H0588 User Manual
HANNspree Flat Panel Television K229 10H1 User Manual
Harbor Freight Tools Air Compressor 67708 User Manual
Hasbro Board Games Cartoon Classics User Manual
Heath Zenith Home Safety Product 2LBL3 User Manual
Huffy Fitness Equipment MQX 2150 User Manual
Husqvarna Blower 1153191 26 User Manual
hussman Refrigerator P N 0420057_B User Manual
Hypertec Carrying Case TAN3706HY User Manual
Impex Exercise Bike ME 708 User Manual