Heath Zenith Home Security System SL 5330 User Manual

OPERATION  
Mode:  
On-Time:  
Works: Day Night  
Test  
Auto  
Manual  
5 Sec  
1, 5, 20 min.  
Until Dawn*  
x
x
x
x
Motion Sensor  
Light Control with  
Protective Lamp  
Shields  
* resets to Auto Mode at dawn.  
Note: When first turned on wait about 1 1/2 minutes for  
the circuitry to calibrate.  
TEST  
Put ON-TIME switch on the sensor  
bottom to TEST.  
ON-TIME  
Model SL-5330  
TEST 1 5 20  
Features  
• Turns on lighting when motion is detected.  
• Automatically turns lighting off.  
AUTO  
ON-TIME  
Put the ON-TIME switch in the 1, 5  
or 20 minute position.  
• Photocell keeps the lighting off during daylight hours.  
TEST 1 5 20  
This package includes:  
MANUAL MODE  
Lamp Holders  
Mounting Strap  
Manual mode only works at night  
because daylight returns the sensor  
to AUTO.  
Rubber Plug  
Flipthelightswitchoffforonesecond  
thenbackontotogglebetweenAUTO  
and MANUAL MODE.  
1 Second OFF  
then...  
Cover  
Plate  
Sensor  
Plastic Hanger  
Light Control  
Manual mode works only with the  
ON-TIME switch in the 1, 5, or 20  
position.  
... back on.  
Mounting Bolt  
Mode Switching Summary  
2 Wire  
Gasket  
TEST  
Connectors  
Move ON-TIME Switch to  
1, 5 or 20 minutes  
AUTO  
6 Screws  
(3 sizes included)  
Flip light switch off  
for one second then  
back on*  
2 PAR Lamps  
MANUAL MODE  
Requirements  
• The Light Control requires 120-volts AC.  
• If you want to use the Manual Mode, the control must  
be wired through a switch.  
Some codes require installation by a qualified  
electrician.  
* If you get confused while switching modes, turn the  
power off for one minute, then back on. After the  
calibration time the control will be in the AUTO mode.  
• This product is intended for use with the enclosed  
gasket and with a junction box marked for use in wet  
locations.  
© 2003 DESA Specialty Products™  
598-1131-01  
 
Loosen the clamp screw in  
thesensorballjointandgen-  
tly rotate the sensor.  
Clamp  
Screw  
TEST AND ADJUSTMENT  
Turn on the circuit breaker and light switch.  
Walk through the coverage  
area noting where you are  
whenthelightsturnon. Move  
the sensor head up, down, or  
sideways to change the cov-  
eragearea.Keepthesensor  
at least 1" (2.5 cm) away  
from the lamps.  
Ball  
Joint  
1
NOTE: Sensor has a 1 /2 minute calibration period  
beforeitwilldetectmotion.Whenfirstturnedon  
wait 1 1/2 minutes.  
Turn the RANGE control to the mid position and the  
ON-TIME control to the TEST position.  
Aim Sensor  
Down for Short  
Coverage  
Adjust the RANGE as  
needed.RANGEsettoohigh  
may  
increase  
false  
MAX  
ON - TIME  
triggering.  
Secure the sensor head's  
aim by tightening the  
clamp screw. Do not over-  
tighten the screw.  
Aim Sensor  
Higher for Long  
Coverage  
MIN  
TEST 1  
5
2 0  
RANGE  
MINUTES  
Bottom of Sensor  
Set the amount of TIME you want the lights to stay  
on after motion is detected (1, 5 or 20 minutes).  
Avoid aiming the sensor at:  
• Objects that change temperature rapidly, such as  
heating vents and air conditioners. These heat  
sources could cause false triggering.  
SPECIFICATIONS  
Range . . . . . . . . . . . . Up to 70 ft. (21 m); 100 ft.  
(30.5 m) with Range Boost.  
[varies with surrounding  
temperature]  
• Areas where pets or traffic may trigger the control.  
Nearby large, light-colored objects reflecting light  
may trigger the shut-off feature. Do not point other  
lights at the sensor.  
Sensing Angle . . . . . . Up to 240°  
Electrical Load. . . . . . Upto300WMax.Incandescent  
[Up to 150 W Max. each lamp  
holder].  
240°  
Power Requirements. 120 VAC, 60 Hz  
Operating Modes. . . . TEST, AUTO and MANUAL  
MODE  
8 ft.  
(2.4 m)  
70 ft.  
(21 m) (30.5 m)  
Boosted  
100 ft.  
Time Delay . . . . . . . . 1 , 5, 20 minutes  
DESA Specialty Products™ reserves the right to  
discontinueproductsandtochangespecificationsatany  
time without incurring any obligation to incorporate new  
features in products previously sold.  
Maximum Range  
Maximum  
Coverage Angle  
The detector is less sensitive to motion directly towards it.  
Motion  
Motion  
Sensor  
Least Sensitive  
Most Sensitive  
598-1131-01  
3
 
TROUBLESHOOTING GUIDE  
SYMPTOM  
POSSIBLE CAUSE  
SYMPTOM  
POSSIBLE CAUSE  
Lightswillnotcome 1. Light switch is turned off.  
Lights stay on 1. A flood lamp is positioned too close to  
on.  
2. Flood light is loose or  
burned out.  
3. Fuseisblownorcircuitbreakeris  
turned off.  
4. Daylight turn-off is in effect (re-  
check after dark).  
5. Incorrect circuit wiring, if this is a  
new installation.  
continuously.  
the sensor or pointed at nearby ob-  
jects that cause heat to trigger the  
sensor. (Reposition the lamp away  
from the sensor or nearby objects).  
2. Light Control is pointed toward a heat  
source like an air vent, dryer vent, or  
brightly-paintedheat-reflectivesurface.  
(Reposition sensor. Reduce Range).  
3. Light Control is in Manual Mode.  
(Switch to Auto.)  
6. Re-aim the sensor to cover de-  
sired area.  
Lights come on 1. Light Control may be installed in  
Lights flash on 1. Heat or light from the lamps may be  
in daylight.  
a relatively dark location.  
2. Light Control is in Test.  
(Set control switch to an  
ON-TIME position).  
and off.  
turning the Light Control on and off.  
(Reposition the lamps away from the  
sensor).  
2. Heat being reflected from other ob-  
jects may be affecting the sensor.  
(Reposition sensor).  
3. Light Control is in the Test mode and  
warming up. (Flashing is normal un-  
der these conditions).  
Lights come on for 1. Light Control may be sensing  
no apparent rea-  
son.  
small animals or automobile traf-  
fic (re-aim sensor).  
2. Range is set too high.  
(Reduce Range).  
Lights flash 1. Sensorisdetectingitsownlights.(Re-  
once,thenstay  
off in Manual  
Mode.  
position lamps to keep area below the  
sensor relatively dark.)  
TECHNICAL SERVICE  
(Do Not Send Products)  
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the  
problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:  
DESA Specialty Products™  
P.O. Box 90004, Bowling Green, KY 42102-9004  
ATTN: Technical Service Specialty Products  
* If contacting Technical Service, please have the following information available: Model Number, Date of  
Purchase, and Place of Purchase.  
No Service Parts Available for this Product  
TEN YEAR LIMITED WARRANTY  
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state  
to state or province to province.  
For a period of ten years from the date of purchase, any malfunction caused by factory defective parts or workmanship  
willbecorrectedatnochargetoyou.Lightbulbsarenotcovered. Toobtainarefundorareplacement, returntheproduct  
to the place of purchase.  
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other  
expendableitemsarenotcoveredbythiswarranty. Unauthorizedserviceormodificationoftheproductorofanyfurnished  
component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience,  
installation, setup time, loss of use, or unauthorized service.  
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and  
components that a customer uses in conjunction with our products.  
THISWARRANTYISEXPRESSLYINLIEUOFALLOTHERWARRANTIES, EXPRESSORIMPLIED, INCLUDINGANY  
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT  
FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDEN-  
TAL, OR CONSEQUENTIAL DAMAGES.  
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO  
LIABILITY ON THE PART OF DESA SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR  
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS,  
WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.  
598-1131-01  
4
 

Grizzly Air Compressor H3370 User Manual
Hans Grohe Indoor Furnishings 10028XX1 User Manual
Harbor Freight Tools Mobility Aid 39178 User Manual
Honeywell Electric Heater HZ 614 User Manual
Honeywell Thermostat 191108AC User Manual
Hotpoint Oven SE102PX User Manual
HP Hewlett Packard Personal Computer xw5000 User Manual
Hunter Fan Fan 20534 User Manual
Hunter Fan Fan 23262 User Manual
Impex Home Gym CB 349 User Manual