HKTS 30SAT-2
Speaker pair
User Guide
English................................
Deutsch..............................
Suomi................................
Français..............................
Italiano................................
Español...............................
Svenska..............................
.............................
Nederlands..........................
Speaker Placement
Expanding a 5.1-Channel System to a 7.1-Channel
System
Mounting Options for
HKTS 30SAT-2 Speakers
Lift base straight
off speaker
Apply pressure evenly
to both sides of base
Shelf Placement
The surround back speakers should be placed against the rear wall
directly behind the listeners, 3–6 feet (0.9m–1.8m) apart, 5–6 feet
(1.5m–1.8m) off the floor.
You can place the HKTS 30SAT-2
speakers on shelves. The satellite
speakers have built-in bases for shelf
placement. You can also remove the
bases if you desire.
To remove a speaker’s base, pull it
straight off the speaker, as shown in
the illustration. Applying even pressure
to both sides of the base will allow it
to slide off smoothly.
Surround Back
Right Speaker
Surround Back
Left Speaker
3 – 6 ft
(0.9m – 1.8m)
Wall-Mounting
IMPORTANT: Read the Speaker Connections
section, on page 5, before wall-mounting
the HKTS 30SAT-2 speakers. You will need to
insert the speaker wires through the wall-
mount brackets and connect the wires to
the speakers during the process of
5 – 6 ft
(1.5m – 1.8m)
Pull sections
apart
installing the wall-mount brackets.
Front Left
Speaker
Front Right
Speaker
Center
Speaker
TV
NOTE: If you are using your own speaker wire,
it must be no thicker than the wire supplied
with the speakers. Thicker wire will prevent
the wall-mount bracket from sliding onto the
speaker.
Subwoofer
1. Decide on the location for the speaker
(see Speaker Placement, opposite).
2. Remove the speaker’s base as explained in
Shelf Placement, above.
Surround Left
Speaker
Surround Right
Speaker
3. Disassemble the wall-mount bracket by sliding the two
sections apart, as shown in the illustration.
If original surround speakers
are behind listeners, move them
to a point to directly at
4. Attach the wall portion of the wall-mount bracket onto
the wall using hardware that is appropriate for the wall’s
construction and materials. We recommend first anchor-
ing the wall-mount bracket using its keyhole, then
attaching it with another anchor through its top opening,
as shown in the illustration. Note that the HKTS 30SAT-2
speakers weigh 3.3 lb (1.5kg). Be sure to use hardware
that can support this weight.
listeners' sides
Surround Back
Right Speaker
Surround Back
Left Speaker
NOTE: If your original surround speakers are located behind the
listeners, you should move them up so they are directly to the
listeners’ sides.
Top opening
If You’re Adding to an Existing HKTS 30 Speaker
System:
Keyhole opening
Bottom opening
Your HKTS 30SAT-2 speakers are designed to expand an exist-
ing HKTS 30 speaker system from 5.1 channels to 7.1 channels.
You can connect the HKTS 30SAT-2 speakers to your receiver’s or
amplifier’s surround back left and surround back right outputs.
If You’re Adding to an Existing HKTS 20 Speaker
System:
Your HKTS 30SAT-2 speakers are designed to expand an exist-
ing HKTS20 speaker system from 5.1 channels to 7.1 channels
by replacing the existing front left and front right speakers. You
can then connect your existing HKTS20 front left and front right
speakers to your receiver’s or amplifier’s surround back left and
surround back right outputs.
3
8. Connect the speaker wire to the speaker terminals, as shown in
NOTE: If you’re running the speaker wire through the wall, you can
bring it out directly behind the wall-mount bracket’s location and insert
it through the bottom opening in the wall portion of the wall-mount
bracket, as shown in the illustration. Inserting it will keep the wire
completely hidden from view once the installation is complete.
the illustration:
• Press down on the top of the terminal to open the connection hole.
• Insert the wire’s bare end all the way into the hole.
• Release the terminal to secure the wire.
Insert the conductor with the colored band into the speaker’s
red ( + ) terminal, and insert the other conductor into the speaker’s
black ( – ) terminal.
Insert wire into
bottom opening
Bring wire out
through here
–
+
5. If you’re not running the speaker wire through the wall, insert
it through the wall portion of the wall-mount bracket, as
shown in the illustration.
Push down on cap
to open hole
Insert bare wire
into open hole
Release cap
to secure wire
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch
each other or the other terminal. Touching wires can cause a short
circuit that can damage your receiver or amplifier.
9. Slide the speaker portion of the wall-mount bracket onto the speaker, as
shown in the illustration. Fit the wall-mount bracket’s grooves onto the
rails in the speaker, and apply even pressure on both sides of the wall-
mount bracket so it slides straight onto the speaker.
• Push the wall-mount bracket all the way onto the speaker until it
snaps into place.
• Pull any slack speaker wire back through the wall-mount bracket
as you slide the wall-mount bracket onto the speaker.
Push down evenly on both sides of wall-mount bracket
Fit bracket grooves
onto speaker rails
6. Pass the speaker wire through the speaker portion of the
wall-mount bracket, as shown in the illustration.
Bring wire in
through here
10. Slide the speaker onto the wall-mount bracket’s wall section,
as shown in the illustration. Pull any slack speaker wire back
through the wall-mount bracket's wall section.
Bring wire out
through here
Slide speaker
onto wall-mount
bracket
7. If you have not already removed the speaker’s base, do so by
pulling it straight off the speaker, as shown in the illustration.
Applying even pressure to both sides of the base will allow it
to slide off smoothly.
Apply pressure evenly
to both sides of base
Lift base straight
off speaker
11. Fit the metal stop plate into the recess on the bottom of the
wall-mount bracket with the pad facing the bracket, and
fasten it to the bracket using two of the supplied
screws. Fastening it will prevent the speaker from detaching
from the wall-mount bracket and will hold the speaker in
position as you rotate it on the wall-mount bracket.
CAUTION: Before making speaker connections, be sure
that your receiver or amplifier is turned OFF and,
preferably, its AC cord is unplugged from the AC outlet.
Stop plate
Supplied screws
4
Speaker Connections
CAUTION: Before making speaker connections, be sure that your
receiver or amplifier is turned OFF and, preferably, its AC cord is
unplugged from the AC power outlet.
Connecting HKTS 30SAT-2 Speakers with the
Supplied Wall-Mount Brackets
Follow the instructions in Wall-Mounting on page 3.
Color-Coding System
The HKTS30 SAT-2 uses the channel color-coding system established
by the Consumer Electronics Association (CEA) to make setting up
your home theater speaker system as easy as possible. The HKTS 30
systems include speaker wires with colored bands on each end.
Connecting HKTS 30SAT-2 Speakers with the
Supplied Bases
1. Remove the speaker’s base (see Shelf Placement, on page 3).
2. Pass the speaker wire through the opening in the speaker’s
base.
3. Connect the speaker wire as described in Color-Coding System,
opposite.
Speaker Position
Wire Color Band
Surround Back Left
Surround Back Right
Brown
Tan
4. Reattach the speaker’s base, as shown in the illustration.
Speakers and receivers/amplifiers have corresponding ( + ) and ( – )
connection terminals. Most electronics manufacturers, including
Harman Kardon, have been using red to denote the ( + ) terminal and
black for the ( – ) terminal. Newer Harman Kardon receivers conform
to the CEA standard and therefore use a color other than red to
denote the ( + ) terminal for some speaker positions.
Each speaker wire included with your system has colored bands at
both ends of the ( + ) conductor. In addition to the colored bands at
each end, each speaker wire’s ( + ) terminal has ribs molded into its
insulation to help you identify it, while the (–) terminal has no ribs.
It is very important to connect each speaker identically: ( + )
on the speaker to ( + ) on the receiver or amplifier, and ( – ) on
the speaker to ( – ) on the receiver or amplifier. Miswiring one or
more speakers results in thin sound, weak bass and a poor stereo
image. With the advent of multichannel surround-sound systems,
connecting all of the speakers in your system correctly is very impor-
tant for achieving the proper ambience and directionality of the sound
coming from the speakers.
To connect the speaker wire to the terminals on the speakers, press
down on the top of the terminal to open the connection hole, insert
the wire’s bare end all the way into the hole, and release the terminal
to secure the wire. Insert the conductor with the colored band into
the speaker’s red ( + ) terminal, and insert the other conductor into
the speaker’s black ( – ) terminal, as shown in the illustration.
–
+
Push down on cap
to open hole
Insert bare wire
into open hole
Release cap
to secure wire
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not
touch each other or the other terminal. Touching wires can
cause a short circuit that can damage your receiver or
amplifier.
5
Receiver
Surround
Back
– +
RIGHT
LEFT
– +
Surround Back Left
Speaker Cable
Surround Back Right
Speaker Cable
(Tan Bands)
(Brown Bands)
– +
– +
Surround Back
Left
Surround Back
Right
6
Troubleshooting
If there is no sound from any of the speakers:
• Check that the receiver/amplifier is on and a disc or other source is playing.
• Make sure that all wires and connections between the receiver/amplifier
and the speakers are connected properly.
• Make sure that none of the speaker wires is frayed, cut or punctured.
• Review the proper operation of your receiver/amplifier.
If there is no sound coming from one speaker:
• Check that the balance control on your receiver/amplifier is not set all the
way to one channel.
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the speaker in question has been enabled and its volume level has not been
turned all the way down.
• Make sure that all wires and connections between the receiver/amplifier
and the speaker are connected properly.
• Make sure that none of the speaker wires is frayed, cut or punctured.
If there is no sound coming from the surround speakers:
• Check your receiver/amplifier’s speaker setup procedure to make sure that
the surround speakers have been enabled and their volume levels have not
been turned all the way down.
• Make sure that all wires and connections between the receiver/amplifier
and the surround speakers are connected properly.
• Make sure that none of the speaker wires is frayed, cut or punctured.
• Review proper operation of your receiver/amplifier and its surround-
sound features.
• Make sure that the movie or TV show you’re watching has been recorded in a
surround-sound mode. If it has not, check to see if your receiver/amplifier
has a different surround-sound mode that you can use.
• Review the operation of your DVD player and the DVD jacket to make sure the
DVD features the Dolby® Digital or DTS® surround-sound mode and that you
have selected that mode using both the DVD player’s menu and the disc’s
menu.
If the system plays at low volumes but shuts off as volume is increased:
• Make sure that all wires and connections between the receiver/amplifier
and the speakers are connected properly.
• Make sure that none of the speaker wires is frayed, cut or punctured.
• If you’re using more than one pair of main speakers, check to be sure that
you’re not operating the system below the receiver/amplifier’s minimum
impedance requirements. If you're not sure sure how to check the
impedance, ask your audio retailer.
7
Specifications
HKTS 30SAT-2 Satellites
Recommended Power
10 ~ 120 watts
Impedance
8 ohms nominal
Sensitivity
86dB @ 2.83V/1 meter
Tweeter
One 3/4" (19mm) dome, video-shielded
Midrange
Dual 3" (75mm) drivers, video-shielded
Dimensions – including stands (H x W x D)
11-25/32" x 4-11/32" x 3-15/32"
(299mm x 110mm x 88mm)
Weight
3.3 lb (1.5kg)
© 2010 Harman International Industries, Incorporated. All rights reserved.
Features, specifications and appearance are subject to change without notice.
Harman Kardon is a trademark of Harman International Industries, Incorporated, registered in the United States
and/or other countries. Designed to Entertain is a trademark of Harman International Industries, Incorporated.
CEA is a registered trademark of the Consumer Electronics Association. Dolby is a registered trademark of Dolby Laboratories.
DTS is a registered trademark of DTS, Inc.
Harman Consumer, Inc.
8500 Balboa Boulevard, Northridge, CA 91329 USA
516.255.4545 (USA only)
Made in P.R.C.
Part # 950-0289-001
8
|