Harbor Freight Tools Paint Sprayer 45211 User Manual

CAR CANOPY  
ASSEMBLY INFORMATION  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2001 by Harbor Freight Tools. All rights reserved. No portion  
of this manual or any artwork contained herein may be reproduced in any  
shape or form without the express written consent of Harbor Freight Tools.  
For technical questions please call 1-800-444-3353  
 
6.  
7.  
8.  
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent  
tripping, falling, back injury, etcetera.  
MAINTAIN A SAFE WORK ENVIRONMENT. Keep work area well lit. Make sure  
there is adequate surrounding work space.  
CHECK FOR DAMAGED PARTS. Before using this product, check for damaged  
parts and any other conditions that may affect the operation of the Canopy.  
Replace or repair damaged or worn parts immediately.  
9.  
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identi-  
cal replacement parts.  
10.  
11.  
12.  
MAINTAIN THIS PRODUCT WITH CARE. Keep the Canopy clean, dry, free of oil,  
grease, liquids, and other debris.  
MAINTENANCE: For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applica-  
tions for which this product was designed. Do not use a small tool, attachment, or  
equipment to do the work of a larger industrial tool, attachment, or equipment.  
Do not use this product for a purpose for which it was not intended.  
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS  
1.  
2.  
DO NOT ATTEMPT TO ASSEMBLE THE CANOPY WHEN HIGH WIND CONDI-  
TIONS EXIST AS PERSONAL INJURY AND/OR DAMAGE TO THE CANOPY  
MAY RESULT.  
MAKE SURE THE CANOPY IS ASSEMBLED AND FIRMLY SECURED (USING  
THE T-STAKES PROVIDED) ON A FLAT, LEVEL SURFACE TO AVOID  
ACCIDENTS.  
3.  
4.  
Do not allow snow to accumlate on the Canopy; the Canopy could collapse.  
Caution: Heavy, wet snow or extreme windy conditions could damage the Car  
Canopy. It is recommended that the Tarp be removed under these conditions, to  
prevent damage to the Car Canopy.  
UNPACKING  
When unpacking, check to make sure all parts shown on the Parts List (page 6) are  
included. If any parts are missing or broken, please call Harbor Freight Tools at the  
number shown on the cover of this manual as soon as possible.  
Caution: Be alert to possible wind damage; proplonged exposure to wind can cause  
fasteners and hardware to loosen as the frame flexes. The Car Canopy’s frame strength  
will be compromised if fasteners and hardware are not tight. Periodically check and make  
sure all fasteners and hardware are tight. Tubes, stakes, tie downs and rope should also  
be periodically checked to make sure the unit is always structurally rigid.  
SKU 45211  
PAGE 3  
REV 04/02 REV 02/04  
 
ASSEMBLY INSTRUCTIONS  
ALL PARTS BELOW REFER TO THE PARTS SHOWN ON PAGE 6.  
Note:To insure safe assembly of this product, two people should assemble  
the Car Canopy.  
1.  
Connect the assorted Tubes and Swaged Tubes (parts #2, 3, 4, 5, 6, 7), 3-Way End  
Pieces (part #8), and 4-Way Center Pieces (part #9) together as shown in Figure A.  
FIGURE A  
2.  
The eight Turnbuckles (part #11) are used to strengthen the frame assembly.  
Attachthe Turnbuckles to the frame assembly and tighten, using a pair of pliers.  
NOTE: Do not over tighten the Turnbuckles, as bending to the frame assembly  
will occur. (See Figure B.)  
FIGURE B  
SKU 45211  
PAGE 4  
 
3.  
4.  
Drape the Tarp (part #14) over the assembled frame and secure the corners of the  
Tarp onto the frame, by inserting the Tarp Ties (part #10) through the metal  
eyelets of the Tarp and around the framing Tubes as shown in Figures C and D.  
Once the corners are fastened, attach the remaining Ball Bungies through the rest  
of the metal eyelets and onto the framing Tubes.  
FIGURE C  
Tarp Ties (#10)  
Caution:The Car Canopy  
must be firmly secured on  
a flat, level and solid  
surface.  
FIGURE D  
5.  
Lift one side of the roof and insert three Vertical Tubes (part #1) into the 3-Way End  
Pieces (part #8) and 4-Way End Piece (part #9). When complete, do the same to  
the other side. (See Figure C)  
6.  
7.  
Insert a Metal Base (part #12, not shown) onto the bottom of each Vertical Tube  
(part #1).  
Secure the Metal Bases (part #12) to the ground, using the T-Stakes (part #13, not  
shown).  
INSPECTION, MAINTENANCE, AND CLEANING  
1.  
Before each use, examine the general condition of the Canopy. Inspect the Canopy  
for damage. Check for loose parts, misalignment, broken parts, tears in the tarp,  
SKU 45211  
PAGE 5  
 
and any other condition that may affect its safe operation.  
Do not use damaged equipment.  
2.  
Keep this Canopy free of oil, grease, liquids, dirt, and other debris. Use only a mild  
detergent and damp cloth when cleaning. Never use flammable or combustible  
liquids to clean the Canopy.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE  
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY  
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EX-  
PRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LI-  
CENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS  
OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT PARTS THERETO.  
PARTS LIST  
ITEM  
DESCRIPTION  
QTY  
6
Vertical Tube (68”)  
1
2
Tube w/2 Side Holes (60”)  
Tube w/1 Side Hole (60”)  
Tube w/o Hole (60”)  
2
4
3
6
4
2
Swaged Tube w/2 Side Holes (60”)  
Swaged Tube w/1 Side Hole (60”)  
Swaged Tube w/o Hole (60”)  
3-Way End Piece  
5
4
6
6
7
6
8
3
4-Way Center Piece  
Tarp Tie  
9
56  
8
NOTE:  
10  
11  
12  
13  
14  
Some parts are  
listed and shown  
for illustration  
purposes only, and  
are not available  
individually as  
replacement  
parts.  
Turnbuckle  
6
Metal Base (Not Shown)  
T-Stake (Not shown)  
Tarp (20’ x 20’)  
12  
1
SKU 45211  
PAGE 6  
 

Graco Baby Accessories ISPS035AA User Manual
Graco TV Cables TI12552a User Manual
Gravely Lawn Mower 915015 1742 ZT 9150156 2048 ZT User Manual
GT Bicycle STREET MACHINE User Manual
HannsG Computer Monitor HG221A User Manual
Harbor Freight Tools Grinder 45707 User Manual
Hasbro Robotics 69173 User Manual
Healthrider Home Gym HREL49010 User Manual
Hotpoint Freezer FZFM 151 xx User Manual
HP Hewlett Packard Tablet XU103UT User Manual