LIFT EXTENSION WINGS
(For Use With Model 94813 Motorcycle Lift)
Model 94830
ASSEMBLY INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape of form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
2.
Keep bystanders, children, and visitors away while assembling and using
the Extension Wings. Distractions can cause you to lose control.
PERSONAL SAFETY
3.
4.
Stay alert. Watch what you are doing, and use common sense during use. Do
not use the Motorcycle Lift while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in
serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep
your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or
long hair can be caught in moving parts.
5.
6.
Do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control in unexpected situations.
Always wear eye protection. Wear ANSI approved safety impact eye glasses,
when using this product.
TOOL USE AND CARE
7.
8.
Store idle tools and equipment out of reach of children and other untrained
people. Tools and equipment are dangerous in the hands of untrained users.
Maintain this product with care. Keep this product clean. Properly maintained
equipment is easier to control. Do not use damaged equipment. Tag damaged
equipment “Do not use” until repaired.
9.
Check for misalignment or binding of moving parts, loose or broken parts,
and any other condition that may affect this product’s operation. If dam-
aged, have this product serviced before using. Many accidents are caused by
poorly maintained tools and equipment.
10.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one product may become hazard-
ous when used on another product.
SERVICE
11.
Product service must be performed only by qualified service technician.
Service or maintenance performed by unqualified personnel could result in a risk
of injury.
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 3
13.
When servicing the Extension Wings, use only identical replacement parts.
Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of injury.
SPECIFIC SAFETY RULES
1.
2.
The Lift Extension Wings are designed only for use with the model 94813
Motorcycle Lift (available from Harbor Freight Tools).
WARNING! Do not exceed the 1,200 pound maximum lifting capacity
of this product. Exceeding the maximum lifting capacity could cause personal
injury and/or property damage. Beware of dynamic loading! Suddenly drop-
ping a load onto this product may create, for a brief instant, an excess load which
may result in damage to the product and/or personal injury.
3.
4.
Industrial applications must follow OSHA requirements.
Store idle tools. When not in use, store the Extension Wings in a clean, dry,
safe location out of reach of children.
5.
6.
7.
Prior to using this product, make sure to read and understand all instruc-
tions and safety precautions as outlined in the model 94813 Motorcycle Lift
manual.
Make sure any load being supported by the Extension Wings is well bal-
anced. Unbalanced loads may cause the lift to tip over, potentially causing
serious personal injury and/or property damage.
Always make sure the object being lifted is properly and safely secured
prior to raising the object.
8.
9.
Always monitor the object being lifted so it does not rock back and forth.
WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 4
ASSEMBLY INSTRUCTIONS
NOTE:
For further references to the parts mentioned in the following pages,
see the Assembly Diagram on page 9 of this manual.
Attach The Side Extensions To The Motorcycle Platform:
5
1
5
3
8
12
8
12
13
14
5
13
14
6
7
12
5
2
12
13
6
14
13
7
14
4
FIGURE A
1.
2.
3.
4.
With assistance, align the mounting hole in each end of the Left Side Extension
(2) with the mounting hole in each end on the left side of the Platform.
Insert two Extension Panel Pipes (8) through the Left Side Extension (2) and the
Motorcycle Platform.
With assistance, slide the Right Side Extension (1) onto the Extension Panel
Pipes (8) and up against the Motorcycle platform.
Insert a Bolt (5) through each end of the two Extension Panel Pipes (8). Then
secure the Extension Panel Pipes in place, using the Washers (6) and Nuts (7)
provided.
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 5
Attach The Ramp Extensions To The Motorcycle Ramp:
1.
With assistance, insert the hook on the Left Ramp Extension (4) into the mount-
ing hole in the end of the Left Side Extension (2). (See Figure A.)
2.
Align the two mounting holes under the Left Ramp Extension (4) with the two
mounting holes in left side of the Ramp. Then secure the Left Ramp Extension to
the Ramp, using two Bolts (12), two Washers (13), and two Nuts (14).
(See Figure A.)
3.
Align the two mounting holes in the Right Ramp Extension (3) with the two
mounting holes in the right side of the Ramp. Then secure the Right Ramp Ex-
tension to the Ramp, using two Bolts (12), two Washers (13), and two Nuts (14).
(See Figure A.)
Attach The Stabilizer Bar To The Motorcycle Lift Frame:
1.
Insert the Stabilizer Bar (11) through the bottom/front frame of the Motorcycle
Lift. (See Figure B.)
2.
Align the two innermost mounting holes under the Stabilizer Bar (11) with the two
mounting holes in the bottom/front frame of the Motorcycle Lift. Then secure the
Stabilizer Bar to the frame, using two Pins (10). (See Figure B.)
3.
Slide a Pipe Cap (9) onto each end of the Stabilizer Bar (11). Then secure the
Pipe Caps to the Stabilizer Bar, using one Pin (10) for each Pipe Cap.
(See Figure B.)
10
9
10
11
10
10
FIGURE B
9
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 6
OPERATING INSTRUCTIONS
1.
WARNING! Do not exceed the maximum lifting capacity of the Exten-
sion Wings (1,200 pounds). Exceeding the maximum lifting capacities could
cause personal injury and/or property damage.
2.
3.
WARNING! Follow all instructions and safety precautions as outlined in the
model 94813 Motorcycle Lift manual.
Make sure the Platform of the Motorcycle Lift is fully collapsed to the floor. Also,
make sure the Removable Plate of the Motorcycle Lift is properly positioned over
the inspection hole of its Platform.
4.
5.
With assistance, roll the object to be raised up the Right and Left Ramp Exten-
sions (3, 4) and onto the Right and Left Side Extensions (1, 2).
You should stabilize the object using tie-down straps (not included) on each side
of the motorcycle with one end of the straps tied to the object and the other end
of the straps tied to the Right and Left Side Extensions (1, 2).
6.
7.
8.
9.
Connect an air hose to the Motorcycle Lift’s Foot Air Valve. Then set the air
compressor’s regulator between 100 and 120 PSI. Do not exceed 120 PSI.
Step on and hold down the right side of the Motorcycle Lift’s Foot Air Valve to
raise the Lift.
When the Motorcycle Lift has been raised to the working height, lower its Safety
Bar completely to prevent the Lift from accidentally lowering.
When work on the motorcycle is completed, check under the Motorcycle Lift to
make sure there are no tools, parts, etc. and that it is safe to lower
the Lift.
10.
11.
12.
Remove the Safety Bar. Then step on and hold down the left side of the Motor-
cycle Lift’s Foot Air Valve to slowly lower the Lift to the floor.
With assistance, remove the tie-down straps from the object. Then, slowly back
the object completely off the Motorcycle Lift.
Turn off the air compressor. Step on and hold down the left side of the Motor
cycle Lift’s Foot Air Valve to release any remaining compressed air in the system.
Then, disconnect the compressor’s air hose from the Foot Air Valve.
13.
Make sure to store the Motorcycle Lift and its Extension Wings in a clean, dry,
safe location out of reach of children and other unauthorized people.
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 7
INSPECTION, MAINTENANCE, AND CLEANING
1.
Before each use: Inspect the general condition of the Extension Wings. Check
for cracked, worn or damaged parts, loose or missing parts, and any other
condition that may affect the product’s safe operation. If a problem occurs, have
the problem corrected before further use.
Do not use damaged equipment.
2.
3.
4.
To clean: Use a damp cloth and a mild detergent. Do not use solvents or other
flammable agents.
When storing: Keep the Extension Wings in a clean, dry, safe location out of
reach of children and other unauthorized people.
CAUTION! All maintenance, service, and repairs not discussed in this
manual should only be performed by a qualified service technician.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS LIST AND
ASSEMBLY DIAGRAM INTHIS MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY
THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 8
PARTS LIST AND ASSEMBLY DIAGRAM
Part
1
2
3
4
5
6
7
Description
Side Extension (Right)
Side Extension (Left)
Ramp Extension (Right)
Ramp Extension (Left)
Bolt
Qty.
1
1
1
1
4
4
4
Part
8
9
10
11
12
13
14
Description
Extension Panel Pipe
Pipe Cap
Pin
Stabilizer Bar
Bolt
Qty.
2
2
4
1
4
4
4
Washer
Nut
Washer
Nut
1
2
5
5
6
6
7
5
8
6
7
7
5
8
6
3
7
10
10
10
9
10
11
4
9
12: Bolt not shown.
13: Washer not shown.
14: Nut not shown.
NOTE:
Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
SKU 94830
For technical questions, please call 1-800-444-3353
PAGE 9
|