Harbor Freight Tools Heat Gun 96289 User Manual

1500 WATT DUAL  
TEMPERATURE HEAT GUN  
Model 96289  
SET UP AND OPERATiNG iNSTRUcTiONS  
Visit our website at: http://www.harborfreight.com  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE THiS MANUAL.  
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised Manual 10c  
 
ranges and refrigerators. There is an  
increased risk of electric shock if your  
body is grounded.  
d. Do not overreach. Keep proper  
footing and balance at all times. This  
enables better control of the power tool  
in unexpected situations.  
c. Do not expose power tools to rain  
or wet conditions. Water entering  
a power tool will increase the risk of  
electric shock.  
e. Dress properly. Do not wear loose  
clothing or jewelry. Keep your hair,  
clothing and gloves away from  
moving parts. Loose clothes, jewelry  
or long hair can be caught in moving  
parts.  
d. Do not abuse the cord. Never use  
the cord for carrying, pulling or  
unplugging the power tool. Keep  
cord away from heat, oil, sharp  
edges or moving parts. Damaged  
or entangled cords increase the risk of  
electric shock.  
f. Only use safety equipment that has  
been approved by an appropriate  
standards agency. Unapproved  
safety equipment may not provide  
adequate protection. Eye protection  
must be ANSI-approved and breathing  
protection must be NIOSH-approved for  
the specific hazards in the work area.  
e. When operating a power tool  
outdoors, use an extension cord  
suitable for outdoor use. Use of a  
cord suitable for outdoor use reduces  
the risk of electric shock.  
4. Power tool use and care  
3. Personal safety  
a. Do not force the power tool. Use  
the correct power tool for your  
application. The correct power tool will  
do the job better and safer at the rate  
for which it was designed.  
a. Stay alert, watch what you are  
doing and use common sense when  
operating a power tool. Do not use  
a power tool while you are tired or  
under the influence of drugs, alcohol  
or medication. A moment of inattention  
while operating power tools may result  
in serious personal injury.  
b. Do not use the power tool if the  
switch does not turn it on and off.  
Any power tool that cannot be controlled  
with the switch is dangerous and must  
be repaired.  
b. Use personal protective equipment.  
Always wear eye protection. Safety  
equipment such as dust mask, non-  
skid safety shoes, hard hat, or hearing  
protection used for appropriate  
c. Disconnect the plug from the power  
source and/or the battery pack from  
the power tool before making any  
adjustments, changing accessories,  
or storing power tools. Such  
preventive safety measures reduce  
the risk of starting the power tool  
accidentally.  
conditions will reduce personal injuries.  
c. Prevent unintentional starting.  
Ensure the switch is in the off-  
position before connecting to power  
source and/or battery pack, picking  
up or carrying the tool. Carrying  
power tools with your finger on the  
switch or energizing power tools that  
have the switch on invites accidents.  
d. Store idle power tools out of the  
reach of children and do not allow  
persons unfamiliar with the power  
tool or these instructions to operate  
the power tool. Power tools are  
dangerous in the hands of untrained  
users.  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
e. Maintain power tools. check for  
misalignment or binding of moving  
parts, breakage of parts and any  
other condition that may affect the  
power tool’s operation. if damaged,  
have the power tool repaired before  
use. Many accidents are caused by  
poorly maintained power tools.  
may contain lead and paint applied to  
homes prior to 1950 is likely to contain  
lead. Once deposited on surfaces,  
hand-to-mouth contact can result in  
the ingestion of lead. Exposure to  
even low levels of lead can cause  
irreversible brain and nervous system  
damage; young and unborn children are  
particularly vulnerable. Before beginning  
any paint removal process you should  
determine whether the paint you are  
removing contains lead. This can be  
done by your local health department  
or by a professional who uses a paint  
analyzer to check the lead content of  
the paint to be removed. LEAD-BASED  
PAINT SHOULD ONLY BE REMOVED  
BY A PROFESSIONAL AND SHOULD  
NOT BE REMOVED BY USING A HEAT  
GUN. Before beginning a paint removal  
process you should determine whether  
the paint you are removing contains  
lead. This can be done by your local  
health department or by a professional  
who uses a paint analyzer to check the  
lead content of the paint to be removed.  
f. Use the power tool, accessories  
and tool bits etc. in accordance  
with these instructions, taking into  
account the working conditions and  
the work to be performed. Use of  
the power tool for operations different  
from those intended could result in a  
hazardous situation.  
5. Service  
a. Have your power tool serviced by a  
qualified repair person using only  
identical replacement parts. This will  
ensure that the safety of the power tool  
is maintained.  
b. Double insulation: When servicing,  
use only identical replacement parts.  
3. Exercise CAUTION when using this  
product outdoors. To reduce the risk  
of electric shock, keep extension cord  
connection dry and off the ground.  
Heat Gun Safety Warnings  
1. Hidden areas behind walls, ceilings,  
floors, soffit boards, and other panels  
may contain flammable materials  
that could be ignited by the heat gun  
when working in these locations.  
The ignition of these materials may not  
be readily apparent and could result in  
property damage and injury to persons.  
When working in these locations, keep  
the heat gun moving in a back-and-forth  
motion. Lingering or pausing in one spot  
could ignite the panel or the material  
behind it.  
4. Persons removing paint should follow  
these guidelines:  
Move the work piece outdoors. If this  
is not possible, keep the work area well  
ventilated. Open the windows and put  
an exhaust fan in one of them. Be sure  
the fan is moving the air from inside to  
outside.  
Remove or cover any carpets, rugs,  
furniture, clothing, cooking utensils and  
air ducts.  
2. Extreme care should be taken when  
stripping paint. The peelings, residue  
and vapors of paint may contain lead,  
which is poisonous. Any pre-1977 paint  
Place drop clothes in the work area to  
catch any paint chips or peelings. Wear  
REV 10c  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
protective clothing such as extra work  
shirts, overalls and hats.  
At the end of each work session put  
the paint chips and debris in a double  
plastic bag, close it with tape or twist  
ties and dispose of properly.  
Work in one room at a time.  
Furnishings should be removed or  
placed in the center of the room and  
covered. Work areas should be sealed  
off from the rest of the dwelling by  
sealed doorways with drop clothes.  
Remove protective clothing and work  
shoes in the work area to avoid carrying  
dust into the rest of the dwelling. Wash  
work clothes separately. Wipe shoes off  
with a wet rag that is then washed with  
the work clothes. Wash hair and body  
thoroughly with soap and water.  
Children, pregnant or potentially  
pregnant women, and nursing mothers  
should not be present in the work area  
until the work is done and all clean up is  
complete.  
5. When working with plastics, varnish,  
or similar materials, gases develop  
that are easily flammable and can  
lead to explosions. Be prepared for  
flames to develop and keep suitable fire  
extinguishing means at hand.  
Wear a dust respirator mask or a  
dual filter (dust and fume) respirator  
mask which has been approved by  
the Occupational Safety and Health  
Administration (OSHA), the National  
Institute of Safety and Health (NIOSH),  
or the United States Bureau of Mines.  
These masks and replaceable filters  
are readily available at major hardware  
stores. Make sure the mask fits.  
Beards and facial hair may keep masks  
from sealing properly. Change filters  
often. DiSPOSABLE PAPER MASKS  
ARE NOT ADEQUATE.  
6. The Nozzle becomes very hot. Do not  
lay the Heat Gun on flammable surfaces  
when operating the Gun or immediately  
after turning the Gun off. Always set the  
Heat Gun on a flat, level surface so that  
the Nozzle tip is directed upwards and  
away from the supporting surface.  
7. Do not use the Heat Gun near flammable  
materials.  
Use caution when operating the Heat  
Gun. Keep the Heat Gun moving, as  
excessive heat will generate fumes  
which can be inhaled by the operator.  
8. Do not point the Heat Gun at people or  
animals. The intense heat can injure  
them.  
9. Do not touch the tube of the heating  
element or the Nozzle when they are hot.  
They will be hot enough to cause burns  
during use and immediately afterwards.  
Keep food and drink out of the work  
area. Wash hands, arms and face and  
rinse mouth before eating or drinking.  
Do not smoke or chew tobacco in the  
work area.  
10. Do not use the Heat Gun on glass.  
Clean up all removed paint and dust  
by wet mopping the floors. Use a wet  
cloth to clean all walls, sills and any  
other surface where paint or dust is  
clinging. DO NOT SWEEP, DRY DUST  
OR VAcUUM. Use a high phosphate  
detergent or trisodium phosphate (TSP)  
to wash and mop areas.  
11. Do not use the Heat Gun as a hair dryer  
or to heat up materials that can be  
damaged by high temperatures.  
12. Maintain labels and nameplates on  
the tool. These carry important safety  
information. If unreadable or missing,  
REV 10c  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
contact Harbor Freight Tools for a  
replacement.  
area, and work with approved safety  
equipment, such as those respirators  
that are specially designed to filter out  
microscopic particles. (California Health  
& Safety Code § 25249.5, et seq.)  
13. Avoid unintentional starting. Prepare to  
begin work before turning on the tool.  
14. Do not leave the tool unattended when  
it is plugged into an electrical outlet.  
Turn off the tool, and unplug it from its  
electrical outlet before leaving.  
18. The warnings, precautions, and  
instructions discussed in this instruction  
manual cannot cover all possible  
conditions and situations that may occur.  
It must be understood by the operator  
that common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
15. This product is not a toy. Keep it out of  
reach of children.  
16. People with pacemakers should  
consult their physician(s) before use.  
Electromagnetic fields in close proximity  
to heart pacemaker could cause  
pacemaker interference or pacemaker  
failure. In addition, people with  
pacemakers should:  
SAVE THESE  
iNSTRUcTiONS.  
• Avoid operating alone.  
• Do not use with power switch locked  
on.  
GROUNDiNG  
TO PREVENT  
• Properly maintain and inspect to avoid  
electrical shock.  
ELEcTRic SHOcK  
AND DEATH FROM iNcORREcT  
GROUNDiNG WiRE  
• Any power cord must be properly  
grounded. Ground Fault Circuit  
Interrupter (GFCI) should also be  
implemented – it prevents sustained  
electrical shock.  
cONNEcTiON:  
Check with a qualified electrician  
if you are in doubt as to whether  
the outlet is properly grounded.  
Do not modify the power cord  
plug provided with the tool.  
Never remove the grounding  
prong from the plug. Do not use  
the tool if the power cord or plug  
is damaged. if damaged, have it  
repaired by a service facility  
before use. If the plug will not fit  
the outlet, have a proper outlet  
installed by a qualified  
17. Some dust created by power sanding,  
sawing, grinding, drilling, and other  
construction activities, contains  
chemicals known [to the State of  
California] to cause cancer, birth defects  
or other reproductive harm. Some  
examples of these chemicals are:  
Lead from lead-based paints  
Crystalline silica from bricks and cement  
or other masonry products  
Arsenic and chromium from chemically  
treated lumber  
electrician.  
Your risk from these exposures varies,  
depending on how often you do this type  
of work. To reduce your exposure to  
these chemicals: work in a well ventilated  
REV 10c  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
Grounded Tools: Tools with Three  
Double insulated Tools: Tools with  
Prong Plugs  
Two Prong Plugs  
Outlets for 2-Prong Plug  
3-Prong Plug and Outlet  
1. Tools marked “Double Insulated” do not  
require grounding. They have a special  
double insulation system which satisfies  
OSHA requirements and complies with  
the applicable standards of Underwriters  
Laboratories, Inc., the Canadian  
1. Tools marked with “Grounding Required”  
have a three wire cord and three prong  
grounding plug. The plug must be  
connected to a properly grounded outlet.  
If the tool should electrically malfunction  
or break down, grounding provides a  
low resistance path to carry electricity  
away from the user, reducing the risk of  
electric shock. (See 3-Prong Plug and  
Outlet.)  
Standard Association, and the National  
Electrical Code.  
2. Double insulated tools may be used in  
either of the 120 volt outlets shown in the  
preceding illustration. (See Outlets for  
2-Prong Plug.)  
2. The grounding prong in the plug is  
connected through the green wire inside  
the cord to the grounding system in the  
tool. The green wire in the cord must  
be the only wire connected to the tool’s  
grounding system and must never be  
attached to an electrically “live” terminal.  
(See 3-Prong Plug and Outlet.)  
Extension cords  
1. Grounded tools require a three wire  
extension cord. Double Insulated  
tools can use either a two or three wire  
extension cord.  
3. The tool must be plugged into an  
appropriate outlet, properly installed and  
grounded in accordance with all codes  
and ordinances. The plug and outlet  
should look like those in the preceding  
illustration. (See 3-Prong Plug and  
Outlet.)  
2. As the distance from the supply outlet  
increases, you must use a heavier gauge  
extension cord. Using extension cords  
with inadequately sized wire causes a  
serious drop in voltage, resulting in loss  
of power and possible tool damage.  
(See Table A.)  
3. The smaller the gauge number of the  
wire, the greater the capacity of the cord.  
For example, a 14 gauge cord can carry  
a higher current than a 16 gauge cord.  
(See Table A.)  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
4. When using more than one extension  
cord to make up the total length, make  
sure each cord contains at least the  
minimum wire size required. (See Table  
A.)  
Symbology  
Double Insulated  
Canadian Standards Association  
Underwriters Laboratories, Inc.  
Volts Alternating Current  
Amperes  
5. If you are using one extension cord for  
more than one tool, add the nameplate  
amperes and use the sum to determine  
the required minimum cord size. (See  
Table A.)  
V~  
A
6. If you are using an extension cord  
outdoors, make sure it is marked with the  
suffix “W-A” (“W” in Canada) to indicate it  
is acceptable for outdoor use.  
No Load Revolutions per Minute  
(RPM)  
n xxxx/min.  
0
7. Make sure the extension cord is properly  
wired and in good electrical condition.  
Always replace a damaged extension  
cord or have it repaired by a qualified  
electrician before using it.  
8. Protect the extension cords from sharp  
objects, excessive heat, and damp or  
wet areas.  
REcOMMENDED MiNiMUM WiRE GAUGE  
FOR EXTENSiON cORDS* (120/240 VOLT)  
EXTENSiON cORD  
LENGTH  
NAMEPLATE  
AMPERES  
(at full load)  
25’ 50’ 75’ 100’ 150’  
0 – 2.0  
2.1 – 3.4  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
-
18  
16  
14  
12  
10  
-
16  
14  
12  
12  
-
3.5 – 5.0  
5.1 – 7.0  
7.1 – 12.0  
12.1 – 16.0  
16.1 – 20.0  
-
-
-
* Based on limiting the line volt-  
age drop to five volts at 150% of  
the rated amperes.  
TABLE A  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 8  
 
Product Applications  
SPEciFicATiONS  
1. When observing the safety rules, this  
Heat Gun is designed for all applications  
with hot air that are listed below:  
120 V~ / 60 Hz / 11.5 A (Peak)  
1500 Watts  
Electrical Input  
Heat  
Temperatures  
Low Setting: 572° F (Maximum)  
High Setting: 1112° F (Maximim)  
Shrinking of shrinkdown tubing,  
solder connectors and solder  
terminals, packaging and electrical  
components.  
Adjustable Heat  
Setting Type  
Three-Way Rocker Switch  
71cJ  
E179876  
Deforming of articles made from  
acrylic, PVC, and polystyrene tubing,  
plates, and profiles as well as most  
woods.  
UNPAcKiNG  
When unpacking, make sure that the  
item is intact and undamaged. If any parts  
are missing or broken, please call Harbor  
Freight Tools at 1-800-444-3353 as soon as  
possible.  
Welding of thermoplastic polymer,  
flooring materials of PVC and  
linoleum, PVC-coated fabric,  
tarpaulins and foils.  
Soldering of tin, special silver solder,  
SMD elements, cable lugs, and for  
loosening soldered connections.  
iNSTRUcTiONS FOR PUTTiNG  
iNTO USE  
Paint removal. Removal of old and  
even thick coatings of oil paint,  
varnish, and synthetic plaster.  
Read the ENTiRE iMPORTANT  
SAFETY iNFORMATiON  
• Drying of color shade samples, filter,  
adhesives, construction joints and  
stucco forms.  
section at the beginning of this  
manual including all text under  
subheadings therein before set up  
or use of this product.  
Joining adhesives. Large surface  
gluing with contact adhesives,  
activation of pressure sensitive  
adhesives, acceleration of bonding  
processes, releasing of bonding  
points as well as releasing or bonding  
of edge bond or veneer.  
TO PREVENT  
SERiOUS iNJURY  
FROM AcciDENTAL  
OPERATiON:  
Turn the Power Switch of the tool  
off and unplug the tool from its  
electrical outlet before  
assembling or making any  
adjustments to the tool.  
Defrosting of icy stairs and steps,  
door locks, trunk lids, car doors or  
water pipes, as well as for defrosting  
refrigerators and ice boxes.  
Note: For additional information regarding the  
parts listed in the following pages, refer  
to the Assembly Diagram near the end of  
this manual.  
Disinfection. With the tool set at  
1112° Fahrenheit, animal sites/  
stables may be disinfected.  
Woodworm infestation may be  
controlled (Caution: Danger of fire.  
REV 08c, 10c  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 9  
 
Do not heat up the wood surface  
excessively.)  
Work Piece and Work Area Set Up  
1. Designate a work area that is clean and  
well-lit. The work area must not allow  
access by children or pets to prevent  
distraction and injury.  
Product Features  
1. See below for the Heat Gun features and  
and controls:  
2. Route the power cord along a safe  
route to reach the work area without  
creating a tripping hazard or exposing  
the power cord to possible damage. The  
power cord must reach the work area  
with enough extra length to allow free  
movement while working.  
Barrel  
Cover (8)  
3. Secure loose work pieces using a vise  
or clamps (not included) to prevent  
movement while working.  
Power Switch (3)  
I - LOW  
4. There must not be objects, such as utility  
lines, nearby that will present a hazard  
while working.  
0 - OFF  
II - HIGH  
General Operating instructions  
Figure A  
1. Make sure Power Switch (3) is in its “0”  
(OFF) position. Then plug Power Cord  
(1) into the nearest 120 volt, grounded,  
electrical outlet. See Figure A.  
OPERATiNG iNSTRUcTiONS  
Read the ENTiRE iMPORTANT  
SAFETY iNFORMATiON  
section at the beginning of this  
manual including all text under  
subheadings therein before set up  
or use of this product.  
2. To turn on the Heat Gun, set its Power  
Switch (3) to “l” or “ll”. See Figure A.  
Switch “l” - Low temperature  
position (572° Fahrenheit maximum).  
Used for mild heating applications,  
i.e., heat shrink tube, heat shrink bag,  
plastic bending, shaping and welding,  
removing old paint coating.  
Tool Set Up  
TO PREVENT  
SERiOUS iNJURY  
FROM AcciDENTAL  
OPERATiON:  
Turn the Power Switch of the tool  
off and unplug the tool from its  
electrical outlet before adjusting  
tool or installing accessories.  
Switch “ll” - High temperature  
position (1112° Fahrenheit  
maximum). Used for intense heating  
applications, i.e., frozen water pipe,  
defrosting refrigerator, and metal  
welding.  
3. To turn off the Heat Gun, set its Power  
Switch (3) to “l”. Then set the Power  
Switch to “0” and unplug the tool from its  
REV 08b, 10a  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 10  
 
electrical outlet. (This method helps cool  
down the Heat Element (11) properly to  
extend the life of the Heat Gun.)  
TO PREVENT SERiOUS iNJURY  
FROM TOOL FAiLURE: Do not  
use damaged equipment. if  
abnormal noise or vibration  
occurs, have the problem  
4. cAUTiON! Danger of fire. Make sure  
to set the Heat Gun on a non-flammable  
surface until it has completely cooled.  
corrected before further use.  
cleaning, Maintenance, and  
Lubrication  
5. Once cooled, store the Heat Gun in a  
clean, dry, safe location out of reach of  
children and other unauthorized people.  
1. DiScONNEcT from power outlet  
and make sure that it is completely  
cooled.  
6. To prevent accidents, turn off the tool  
and disconnect its power supply after  
use. Clean, then store the tool indoors  
out of children’s reach.  
2. BEFORE EAcH USE, inspect the  
general condition of the Heat Gun.  
Check for loose screws, misalignment  
or binding of moving parts, cracked or  
broken parts, damaged electrical wiring,  
and any other condition that may affect  
its safe operation.  
MAiNTENANcE AND  
SERViciNG  
Procedures not specifically  
explained in this manual must  
be performed only by a qualified  
technician.  
3. AFTER USE, clean the external surfaces  
of the tool with a clean, moist cloth and  
mild detergent. Then dry. Do not use  
solvents.  
TO PREVENT  
SERiOUS iNJURY  
FROM AcciDENTAL  
OPERATiON: Turn the Power  
Switch of the tool off and unplug  
the tool from its electrical outlet  
before performing any  
inspection, maintenance, or  
cleaning procedures.  
4. cAUTiON! All maintenance, service,  
and repairs not mentioned in this manual  
must only be performed by a qualified  
service technician.  
5.  
WARNiNG! if the supply cord of  
this power tool is damaged, it must be  
replaced only by a qualified service  
technician.  
Troubleshooting  
Problem  
Possible causes  
Possible Solutions  
1. Turn Power Switch to “l” or “ll”.  
2. Check power at outlet.  
Heat Gun will not turn 1. Power Switch set at “0”.  
on.  
2. No power at outlet.  
3. Cord not connected.  
3. Check that cord is plugged in.  
Unsatisfactory results. 1. Improper heat setting.  
1. Adjust heat setting (“l” or “ll”) for  
correct application.  
Follow all safety precautions whenever diagnosing or servicing the  
tool. Disconnect power supply before service.  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 11  
 
PLEASE READ THE FOLLOWiNG cAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY  
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR  
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE  
OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED  
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR  
ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY  
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK  
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT  
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
PARTS LiST  
Part  
1
Description  
Power Cord & Plug  
Q’ty  
Part  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
Description  
Barrel Mounting Flange  
Fan Cover  
Q’ty  
1
1
1
7
1
3
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
2
2
Terminal Block  
Power Switch  
Screw  
3
Fan  
4
Screw  
5
Wire Clamp  
Screw  
Motor Mounting Plate  
Motor  
6
7
Screw  
Rear Enclosure  
Right Enclosure  
Screw  
8
Barrel Cover  
Ring  
9
10  
11  
Barrel  
Left Enclosure  
Label  
Heat Element  
Record Product’s Serial Number Here:  
Note: If product has no serial number, record month and year of purchase instead.  
Note: Some parts are listed and shown for illustration purposes only, and are not available  
individually as replacement parts.  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 12  
 
ASSEMBLY DiAGRAM  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 13  
 
LiMiTED 90 DAY WARRANTY  
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality  
and durability standards, and warrants to the original purchaser that this product is free from  
defects in materials and workmanship for the period of 90 days from the date of purchase. This  
warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or  
accidents, repairs or alterations outside our facilities, criminal activity, improper installation,  
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,  
injuries to persons or property, or for incidental, contingent, special or consequential damages  
arising from the use of our product. Some states do not allow the exclusion or limitation of  
incidental or consequential damages, so the above limitation of exclusion may not apply to  
you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS  
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the complaint  
must accompany the merchandise. If our inspection verifies the defect, we will either repair or  
replace the product at our election or we may elect to refund the purchase price if we cannot  
readily and quickly provide you with a replacement. We will return repaired products at our  
expense, but if we determine there is no defect, or that the defect resulted from causes not  
within the scope of our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which  
vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
SKU 96289  
For technical questions, please call 1-800-444-3353.  
Page 14  
 

Grandstream Networks Telephone Accessories HT286 User Manual
Harbor Freight Tools Bicycle Accessories 95365 User Manual
Harman Kardon Home Theater System HS 150 User Manual
Hotpoint Refrigerator HTR15ABM User Manual
HP Hewlett Packard Computer Monitor ZR30w User Manual
HP Hewlett Packard Landscape Lighting 3400A User Manual
Huey Chiao Bluetooth Headset HCB38 User Manual
Hunter Fan Humidifier 41574 01 User Manual
Husqvarna Cordless Saw K750 User Manual
Husqvarna Utility Vehicle 4421 D DX DXL User Manual