Item 92188 Angle Drill
With Keyless Chuck
Operating Instructions
3491 Mission Oaks Blvd., Camarillo, CA 93011
'LVWULEXWHGꢀH[FOXVLYHO\ꢀE\ꢀ
Š
+DUERUꢀ)UHLJKWꢀ7RROV ꢁ
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Thank you for choosing a Harbor Freight Tools product! For future reference, please com-
plete the owner’s record below:
model:___________________ Purchase Date:__________________
Save the receipt, and these instructions. It is important that you read the entire instruction
sheet to become familiar with this product before you begin using it.
Technical Specifications:
Angle Drill includes 3/8” Shaft Attachment
Hex Shaft Size: 5/16”
Spindle Thread: 3/8” - 24
Maximum Speed: 6000 RPM
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of
personal injury and damage to equipment.
Read all instructions before using this product!
1. Do not exceed 6,000 RPm maximum speed.
2. Avoid working alone. If an accident happens, an assistant can bring help.
3. Keep work area clean. Cluttered areas invite injuries.
4. Keep children away. Children must never be allowed in the work area. Do not let them handle ma-
chines, tools, or extension cords.
ReV 09b
Assembling and Operating the Angle Drill
1.
Unplug the electric drill or disconnect the air hose on the air powered drill before attempting to attach
the Angle Drill. The drill used to power the Angle Drill should also be turned OFF.
2.
Insert the Shaft (#13) of the Angle Drill into the chuck of the drill being used to power this attachment.
Properly align and tighten the Shaft in place (read instructions provided with the drill being used to
power this attachment).
3.
4.
Insert the bit of choice into the Chuck Casing (#12) of the Angle Drill and tighten in place (the chuck is
keyless).
Properly grip the Drill/Angle Drill Attachment. One hand will operate the power drill and the other
hand will wraparound the Spindle Case (#2) of the Angle Drill attachment, to support the tool while it
is being used.
5.
6.
Before using the Angle Drill on the workpiece, turn on the drill and test its operation. Make sure the
Angle Drill is properly aligned for maximum leverage. Check that the drill bit is properly inserted.
The Angle Drill is now ready to be used. Align the drill bit on the workpiece. While firmly holding the
power drill and the Angle Drill, turn on the power drill and begin drilling.
Caution: Always unplug the power drill or disconnect the air hose on air powered drills, before
changing bits or making adjustments to the Angle Drill.
Parts List
#
Description
Qty
1
2
3
4
5
6
7
8
Needle Bearing
Spindle Case1
Clutch Pin
Ball Bearing
Bevel Gear
Ball Bearing
Angle Head
Key
Bevel Gear
Bearing Cap
Chuck Casing
Chuck Screw
Shaft
1
1
2
1
1
1
1
1
1
1
1
1
9
10
11
12
13
Note: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
SKU 92188
For technical questions, please call 1-800-444-3353.
Page 3
Parts Diagram
PLeASe ReAD tHe FOLLOWING CAReFULLY
tHe mANUFACtUReR AND/OR DIStRIBUtOR HAS PROVIDeD tHe PARtS DIAGRAm
IN tHIS mANUALASAReFeReNCe tOOL ONLY. NeItHeR tHe mANUFACtUReR NOR
DIStRIBUtOR mAKeS ANY RePReSeNtAtION OR WARRANtY OF ANY KIND tO tHe
BUYeR tHAt He OR SHe IS QUALIFIeD tO mAKe ANY RePAIRS tO tHe PRODUCt
OR tHAt He OR SHe IS QUALIFIeD tO RePLACe ANY PARtS OF tHe PRODUCt. IN
FACt, tHe mANUFACtUReR AND/OR DIStRIBUtOR eXPReSSLY StAteS tHe ALL
RePAIRS AND PARtS RePLACemeNtS SHOULD Be UNDeRtAKeN BY CeRtIFIeD
AND LICeNSeD teCHNICIANS AND NOt BY tHe BUYeR. tHe BUYeR ASSUmeS
ALL RISK AND LIABILItY ARISING OUt OF HIS OR HeR RePAIRS tO tHe ORIGINAL
PRODUCt OR RePLACemeNt PARtS tHeRetO, OR ARISING OUt OF HIS OR HeR
INStALLAtION OF RePLACemeNt PARtS tHeRetO.
SKU 92188
For technical questions, please call 1-800-444-3353.
Page 4
|