Harbor Freight Tools Brush Cutter 95343 User Manual

3
/ ” ROTARY SPOT WELD  
8
CUTTER  
Model 95343  
SET UP AnD OPERATing inSTRUCTiOnS  
Visit our website at: http://www.harborfreight.com  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE ThiS MAnUAL.  
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork  
contained herein may be reproduced in any shape or form without the express written consent of  
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Manual Revised 10d  
 
UnPACKing  
inSPECTiOn, MAinTEnAnCE,  
AnD CLEAning  
When unpacking, check to make sure that the  
item is intact and undamaged. If any parts are missing  
or broken, please call Harbor Freight Tools at the  
number shown on the cover of this manual as soon as  
possible.  
1.  
WARning! Make sure the Power Switch  
of the drill is in its “OFF” position and that the  
tool is unplugged from its electrical outlet before  
performing any inspection, maintenance, or  
cleaning procedures.  
ATTAChing AnD REMOVing  
ThE BiT  
2.  
BEFORE EACh USE, inspect the general  
condition of the tool. Check for loose or broken  
parts and any other condition that may affect its  
safe operation. If abnormal noise or vibration  
occurs, have the problem corrected before  
further use. Do not use damaged equipment.  
1.  
2.  
Insert the Shaft into a vise. Grasp the Bit with a  
wrench and unscrew the Bit.  
Thread on the new Bit or flip to unused cutter  
3.  
Clean the Spot Weld Cutter after each use.  
Remove any debris, grease, oil and dirt. Store in  
the Blow Mold Case in a secure place out of the  
side.  
3.  
1.  
2.  
Remove Shaft and Bit from vise.  
reach of children.  
OPERATiOn inSTRUCTiOnS  
The Spot Weld Cutter is now ready to be  
mounted to the drill. Read the drill owner’s  
manual for instructions on properly mounting drill  
bits.  
Before using the Spot Weld Cutter, make certain  
that the work piece is firmly clamped and secured  
in place. Place the Spot Weld Cutter Bit over  
the spot weld and slowly begin drilling into the  
work piece. Always hold the drill firmly with both  
hands to ensure safe operation of the Spot Weld  
Cutter. Note: If Bit does not stay in spot weld  
depression, dimple the center of the weld with a  
punch (not included).  
3.  
Drill until the spot weld is removed. Do not over  
drill.  
note:When working on a vehicle, be certain to protect  
all electrical components from damage.  
Follow the vehicle owner’s manual for securing  
electrical systems. Make certain that the drilling  
path is clear of all cables, wires and electrical  
components.  
a. Disconnect and isolate the negative battery  
cable and disarm the passive restraint  
system.  
b. Protect computer modules, connectors, and  
wiring from dirt, heat, moisture and metal chips.  
SKU 95343  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
PARTS LiST  
Part Description Quantity  
1
2
Shaft  
Bit  
1
1
ASSEMBLY DiAgRAM  
1
2
note:Some parts are listed and shown for illustration purposes only, and are not available individually as  
replacement parts.  
PLEASE READ ThE FOLLOWing CAREFULLY  
THe MANUFACTUReR AND/OR DISTRIBUTOR HAS PROvIDeD THe PARTS LIST AND ASSeMBLY DIAGRAM  
IN THIS MANUALASAReFeReNCe TOOL ONLY. NeITHeR THe MANUFACTUReR OR DISTRIBUTOR MAKeS  
ANY RePReSeNTATION OR WARRANTY OF ANY KIND TO THe BUYeR THAT He OR SHe IS QUALIFIeD TO  
MAKe ANY RePAIRS TO THe PRODUCT, OR THAT He OR SHe IS QUALIFIeD TO RePLACe ANY PARTS  
OF THe PRODUCT. IN FACT, THe MANUFACTUReR AND/OR DISTRIBUTOR eXPReSSLY STATeS THAT  
ALL RePAIRS AND PARTS RePLACeMeNTS SHOULD Be UNDeRTAKeN BY CeRTIFIeD AND LICeNSeD  
TeCHNICIANS, AND NOT BY THe BUYeR. THe BUYeR ASSUMeS ALL RISK AND LIABILITY ARISING OUT  
OF HIS OR HeR RePAIRS TO THe ORIGINAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARISING  
OUT OF HIS OR HeR INSTALLATION OF RePLACeMeNT PARTS THeReTO.  
SKU 95343  
For technical questions, please call 1-800-444-3353.  
Page 4  
 

Hamilton Beach Iron 840101300 User Manual
Harbor Freight Tools Mobility Aid 39178 User Manual
Hotpoint Clothes Dryer TVFM60C FUTURA User Manual
Hotpoint Cooktop EW20 User Manual
HP Hewlett Packard Computer Accessories 130900 User Manual
Husqvarna Brush Cutter SPM1702SM User Manual
Husqvarna Lawn Mower 445e User Manual
Husqvarna Snow Blower ST724 User Manual
Hypertec Carrying Case N11028KHY User Manual
IKEA Plumbing Product AA 220170 3 User Manual