Haier Washer XQS70 98 User Manual

Double-drive Automatic Washing Machine  
User's manual  
This manual is for  
XQS70-98  
Please read this manual carefully  
before using.  
Retain it for future reference.  
 
Names of the parts  
Top lid components  
Water absorption  
cushion  
Rear faceplate  
Water inlet valve  
Inner cover components  
Detergent box  
Control panel seat  
Outer tub cover  
Power cord  
Balance ring  
Attachment block 3 pieces  
Inner tub  
Draining hose  
hanging hole  
Lint filter  
Pulsator  
Control panel coating  
Cabinet  
Handle  
Liquid blenching filler  
Drain hose  
Back cover  
Adjustable leg  
The figure in this manual being sketch map and with the improvement of our products, the machine you buy  
is like to be different from the figure indicated in the manual .Please understand.  
Meaning and description of the symbols  
Warning sign  
Contents marked with that symbol are related to the safety of the product  
and the personal safety of the users. Please operate in strict conformity to  
the contents, otherwiseit may result in damage of the machine or influence  
the personal safety of the users.  
Forbidden sign  
Contents marked with that symbol are actions forbidden to perform.  
Performing of those actions may result in damage of the machine  
or influence the personal safety of the users.  
1
 
Safety precautions  
The washing machine must be positioned  
Please plug the power plug on special  
receptacle. Be sure to use three-pins  
power receptacle. Ensurethat the earthing  
prong of the power receptacle is earthed  
reliably. Use leakage protector if possible.  
so that the plug isaccessible. Be sure topull the  
plug off and close the water faucet in  
following cases: power failure, delivering  
the machine, setting the machine idle or  
c l e a n i n g t h e m a c h i n e . D o n o t p l u g  
or pull the power plug with wet hand.  
Earth  
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.  
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe with  
dry cloth carefully.  
If the power cord or the power plug is bad, to avoid risk it is  
required to have it replaced by the technicians of our  
special shop or the after-sale service department.  
In case the washing machine is installed on ground with  
carpet, do not block the ventilation hole with carpet.  
Do not use water hotter than 50  
The ventilation  
holes at the bottom  
Soft object  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations in spinning.  
Do not put the machine at damp place like  
the bathroom. Never wash it with water. Do  
not put wet laundries on the control panel.  
Do not let the machine share one receptacle with other  
electric appliances. If the plugging into the receptacle  
is loose, do not use the plug any more.  
2
 
Do not decompose, repair or alter the machine  
by yourself.  
Do not stretch hands into the working machine.  
It is dangerous even if the rotation is slow.  
Take special care of the children.  
Do not wash laundries with volatile materials  
(such as thinner, petrol etc.).  
Do not put any hot or heavy items (such as the kettle  
with hot water) on the washing machine  
Benzene  
The appliance is not instruct for use of  
young children of infirm persons without  
supervision.Young children should be  
supervised to ensure that they do not  
play with the appliance.  
Keep the machine away from direct sunlight and  
heat source like the heater.  
To prevent your laundries and washing machine from  
damages, be sure to take out all of the foreign materials  
from your pocket, such as coins, buttons, sandor hair  
pins etc.  
The lint filter shall be kept in good condition, and  
installed to proper position. If the lint filter is lost  
or damaged, please contact the local after-sales  
service department of our company.  
The cover of lint filter  
lint filter  
lint filter  
Install  
Dismantle  
Before washing, please check if the water tap is open,  
and if the water inlet pipe is connected properly.  
The back coverof lint filter  
Dismantle  
Install  
It is suggested to use low-foaming washing powder.  
3
 
Please install and adjust the machine according to the requirement of the manual.  
It is very important to your security and correct operating the machine.  
Install the inner cover components  
1.Open the top lid of the washing machine.  
2.Put the inner cover component on the outer tub cover, aiming  
Outer tub cover  
the inner cover shaft to the installation hole of the corresponding  
outer tub cover shaft groove.  
shaft groove  
Inner cover shaft  
3.Firstly insert the inner cover shaft of I side into the correspon  
-ding outer tub cover shaft groove, then push the another inner  
cover shaft into the corresponding outer tub cover shaft groove.  
Please install to designated position to guarantee there are no  
dropping or abnormal sound in opening and closing of the inner  
cover, and the operation shall be smooth. Do not dismount the  
inner cover component after washing.  
Outer tub cover  
Inner cover  
Install the bottom plate  
After opening the package, please lean  
the washing machine gently down on  
soft items (like towel cloth, blanket, etc.).  
Install the bottom plate to the bottom  
of the machine with eight screws by a  
c r o s s s c r e w d r i v e r , t h e n l i f t t h e  
machine up gently. See to the figure:  
Back  
Front  
Bottom plate  
Soft items  
Screw  
Adjust the Installation position  
The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in  
unstable running or stoppage of the machine. Please adjust it with following methods:  
Confirm it's horizontal  
Hang the plumb to confirm it's horizontal  
Adjust the adjustable foot  
(1) To twist theadjustable foot atthe right frontof  
the cabinet (frontthe sight of front), please first  
lift up theside of the foot slightly,loosen the  
adjustable nut, andtwist the foot.  
adjustable nut  
adjustable foot  
Loosen  
Fasten  
High  
Low  
(2) Fasten thenut after adjustment.  
4
 
How to change the direction of the drain hose  
1.Lean the machine downgently with the front  
surface facing the ground. Loosen the eight  
screws by a crossscrewdriver.  
3.Extend the drain hose from the right side. Push the  
drain hose into the groove with hands.  
Back  
Bottom plate  
Front  
Soft item  
2.Pull out the drain hose from the groove at the left side.  
Use groove at  
this side after  
direction changing  
4.Install the bottom plate (as per indicated before),  
then lift the machine up gently.  
Page 4  
Usage of the drain hose  
The drain hoseshall drain smoothly  
1.The height of the drain hose shall be  
less than 10cm, or the drainage will not  
be smooth, and cost such long time that  
the machine may stop at mid way.  
4.If extra drain hose is needed, please  
make separate purchase. The inner  
diameter of the extra hose shall not  
less than 30mm, and the length shall  
not exceed 1.5m.  
2.Do not ramp or press the drain hose.  
3.If the drain hose is too long, cut it at mid  
point. To make smooth drainage, cut the  
front end of the hose slantingly.  
5.If the extrahose is toolong, cut it  
either at A or at B point.  
5
 
Install the water inlet hose  
Confirm the water faucet  
water faucet, suitable  
water faucet, not suitable  
The exit end face of the faucet  
It is required that the front end shall be longer than 10mm.  
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.  
Connection between the water inlet hose jointerand the water faucet  
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the  
water inlet hose component. See to Figure 1.  
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.  
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen  
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise  
it may leak water. See to Figure 3.)  
water inlet hose jointer  
Screw  
Slider  
Nameplate  
Bushing  
Lock level  
Screw knife  
water inlet hose  
Figure 1  
Figure 2  
Figure 3  
3.Fasten the four screws evenly. See to Figure 4.  
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure  
to seal up the exit end face of the faucet. See to Figure 5.  
Remark: .Before twisting the fastening nut, the threading is 4mm above the upper  
surface of the nut. After twisting, the threading is less than 2mm above the upper  
surface of the nut. See to Figure 6  
about 4mm after twisting  
About above 2mm after twisting  
Screw nut  
Figure 4  
Figure 5  
Figure 6  
6
 
Connection between the water inlet hose and the washer  
1.Do not take off the water absorption cushion. Please check if the  
cushion is dropped or damaged before each usage. If it happens  
nut of the water inlethose  
please contact our after-sale department immediately.  
2 Put the nut of the water inlet hose on the valve jointer.  
3 Fasten the nut. Swing it gently to confirm if it's suitable.  
jointer of the water inletvalve  
water absorption cushion.  
Connection between the jointer of the water inlet hose  
and the water inlet hose  
1.Push down the slider. Insert the water inlet hose into the jointer.  
the jointer of the water inlet hose  
Slider  
2 Hang the lock lever to the jointer. Release the slider till a click sound is heard.  
Locking level  
Check the connection between the jointer of the water inlet hose  
and the water faucet  
1.Swing the hose gently to confirm if it is fastened stable.  
2.After installation, open the faucet to check if it leaks.  
3.Do not bend the hose with overstrain.  
4.Before each usage please check if the connection  
between the jointer of the water inlet hose and the  
water faucet, and the installation of the water inlet  
hose are firm, so as to prevent dropping from  
improper installation position.  
Dismantle the water inlet hose  
1. Close the water faucet.  
2. Press the locking lever. Push down the slider. Then pull of the water inlet hose.  
If the machine is used frequently, the jointer of the water inlet hose can be kept  
on the faucet to prevent damaging the fixing screw.  
Locking level  
Slider  
Remarks: use the newhose sets supplied with the washer.  
Any other old hose sets should not be used.  
7
 
1 Preparation before washing  
Preparation before washing  
1.Connect the water inlet hose. Open the water faucet.  
2.Confirm that the washing machine is earthed reliably.  
Then insert the power plug into the receptacle. The  
earth terminal shall not link to gas pipeline and  
faucet water pipeline.  
3.Put down the drain hose.  
Pay attention to following before washing  
Check  
if C l e a r t h e Tie the long The quantity of  
When the pulsator  
Pay attention to followings before washing the laundries  
the laundries pocket. Take strips; fasten the laundries is running , the  
has special out the coins, the buttons; shall not be too buttons of the  
requirement sand, hairpins close zippers. large. Stretch laundries may  
on washing etc.  
and loosen the cause noise. For  
laundries before t h e s a k e o f  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
a. Check ifthe laundries are applicable for washing with machine.  
b. Divide thelaundries that are not colorfast from otherlaundries.  
c. Put thoselaundries difficult to absorb water into waterwith hand.  
d. For thoselaundries with heavy soil, pleasefirst remove thedirt like mudor dust.  
For the partswith heavy soil, please applydetergent on them in advance, which  
can make iteasier to remove the soil.  
e. For thoselaundries that may get lintball and thosewith long fur, turn itover before  
putting in.  
f. Do notput those laundries polluted by chemicals into the washing machine directly.  
8
 
2 Put in the laundries  
The capacity of washing and spinning of the machine  
refer to thelargest weight ofthe standard laundries  
under dry condition that can bewashed or spinning  
in one time. One time washing quantity shall be lower  
than the ratedcapacity.  
The thickness, size, type of the cloth will influence the  
actual washing capacity. It is suitable for one time  
washing to putin reasonable amount of laundries  
and the laundries can be turnedround in washing.  
Do not select above 4 water level for laundries small  
than 1.0kg, so as to avoid splashing of water.  
3 Usage of the detergent  
Add the washing powder or softener into the detergent box  
directly as indicated in the left figure.  
Washing powder inlet entrance  
After adding washing powder ,please close the detergent box.  
See to following table for the dosage of the washing  
powder.  
Softener inlet entrance  
How to use the washing powder  
Direct dissolved in the machine(not applicable for fuzzy  
and reserve programs)  
1.Fill small quantity of water.  
2.Add the power. Run for 30 seconds to dissolve  
it completely.  
3.Put in the laundries. Select suitable water level.  
How to use the whitener  
Fill water to decided level .Dilute the whitener with  
container. Pour it slowly into the washing tub.  
The instant dissolving of the washing powder:  
1. Prepare warm water of 30 and a container.  
2. Add the powder while stirring to fully dissolve it.  
Avoid using whitener on laundries with colour or  
pattern as they are prone to lose colour.  
It is suggested to use liquid detergent when you  
use QUICK WASH.  
The whitener shall not touch the laundries directly.  
Please add the powder according to the laundry quantity,  
water level and water quantity.  
Refer to the user's manual for the usage and  
quantity of the whitener.  
It is suggested not to use high sudsing detergent.  
Washing powder with poor quality or not used for a long  
period may get blocked. Please clean the detergent box  
in time.  
For powder whitener, please dissolve it before use.  
9
 
4 Use the operation buttons  
Description of the function of the buttons  
Digital tube  
Mode and meaning of the VFD indicator  
During sensing, it displays  
Flashing indicating the running program  
During operation of programs, it displays the  
remained time (minute) or remained times of  
the corresponding procedure  
On indicating the program about to run or the selection mode  
The digital tube corresponding to the running  
program lights.  
Minutes  
Minutes  
Times  
Minutes  
SOAK  
WASH  
RINSE  
SPIN  
RINSE button  
SOAK button  
WASH button  
SPIN button  
Push the RINSE button to set the rinse  
procedure.  
Push the SOAK button  
to set the soak procedure.  
During standard and  
Push the WASH button  
to set the wash procedure.  
During standard and  
jeans programs, push the  
WASH button to set different  
wash time (from 0 to 25  
minutes)  
Push the SPIN button  
to set the spin  
procedure.  
During standard and jeans programs,  
push the RINSE button to set different  
rinse times ( 0, 1, 2, 3, 4 times)  
During fibre , cotton woollen  
and silk programs, push the RINSE  
button to select rinse procedure, but  
the rinse times can not be changed.  
During quick , posthaste programs,  
push the RINSE button, the machine  
have no reaction.  
During standard and  
jeans programs, push  
the SPIN button to set  
different spin time  
(from 0 to 9 minutes)  
During fibre , cotton,  
woollen and silk  
programs, push the  
SPIN button to select  
spin procedure, but the  
spin time can not be  
changed.  
During quick , posthaste ,  
programs, push  
the SPIN button, the  
machine have  
no reaction.  
jeans programs, push the  
SOAK button to set different  
soak time (10,20,30 or 40  
minutes)  
During fibre and cotton  
programs, push the SOAK  
button to select soak  
During fibre , cotton woollen  
and silk programs, push  
the WASH button to  
procedure, but the soak time  
can not be changed.  
select wash procedure,  
but the wash time can  
not be changed.  
During standard program, the machine  
is set to save water program. If you  
push the RINSE button before starting  
operation, it will change to water  
storage rinse program.  
During quick, posthaste,  
woollen and silk programs,  
push the SOAK button, the  
machine have no reaction.  
During quick, posthaste  
programs, push the WASH  
button, the machine have  
no reaction.  
10  
 
Child lock function  
This function is used to protect the children and prevent them from changing the  
washing procedure.  
Push and hold the WATER LEVEL button and SPIN button, then push down the  
POWER ON/OFF button. The digitron displays CL . You can continue setting desired  
washing procedures. After setting, push down the START/PAUSE button. The child  
lock function is activated.All of the buttons are locked and cannot make selection.  
Release the child lock function: push down the WATER LEVEL and SPIN button at  
the same time for more than 1 second. After a beep sound, the child lock function is released.  
Power On/Off button  
to switch on  
Push the POWER ON/OFF button  
the power. When the power is on, push  
to switch off the power.  
it again  
to switch on  
Push the POWER ON/OFF button  
the power. If the START/PAUSE butto  
n is not  
utomatically  
pushed, the washing machine will a  
switch off the power after 5 minutes.  
Reserve/remain time indicator digitron  
During sensing, it displays --  
During reserve procedure, it displays the remained reserve time (in hour)  
During operation of programs, it displays the remained time (minute). If the remained time exceeds 99 minutes,  
it adopts  
A
at tens place to represent 100 minutes, b to represent 110 minutes. For instance, A3 represents 103 minutes.  
Page 16  
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)  
10  
9
7
5
3
1
Time remained(minutes)  
8
FIBRE  
NORMAL  
QUICK  
6
COTTON  
4
POSTHASTE  
JEANS  
WOOLLEN  
Reserve(hours later)  
2
SILK  
POWER  
ON/OFF  
START  
PAUSE  
PROGRAM  
WATER  
LEVEL  
RESERVE  
Start/Pause button  
After the power is switched on, push it to  
Start the machine  
During working, push it to pause working.  
During pause, push it to resume working.  
WA  
TER LEVEL  
button  
RER  
SER  
VE button  
The washing machine can detect the laundries automatically.  
After detection, it will set the water level to suitable value  
among 4, 6, 8,and 10 automatically.  
In normal operation mode,  
the reserve indicator light  
is off. The time remain  
indicator light is on. The  
digitron displays the time  
remained (in minute)  
PROGRAM  
selection button  
You can also set water level by self. After the machine  
is started, it will not set water level automatically. You shall  
push the START/PAUSE button to make new setting.  
If there's water inside the tub, the machine cannot detect the  
laundries and will display water level 6 .  
Following automatic programs are available for selection  
Applicable situation  
Common washing  
Program  
Normal  
before the washing is  
finished.  
If wet laundries are put in, it may display water level 10 . You  
must set suitable water level by yourself.  
Quick and high-efficiency wash for  
common laundries  
Push down the RESERVE  
button. The reserve  
Quick  
If POSTHASTE program is selected, it will display water  
Super quick wash of the laundry  
under 1 kg with light soil  
Posthaste  
Jeans  
indicator light is on ,The  
digitron displays the reserve  
time of finishing washing  
(in hour).When the machine  
is started, the reserve  
indicator light is on,  
level 3 . When water level  
2
is reached in water filling, it will  
perform washing while filling water. When water level  
reached, it will change to normal washing.  
3
is  
Washing the relatively big and thick laundriesr  
Washing the chimical fiber laundries  
Washing the cotton textiles  
During operation of wash and rinse program, you can push  
down the water level button to add water. When you release  
the button, or it reaches the overflow water level, the machine  
will stop adding water. The water level decided may be  
different from actual value because of the different moisture  
level of the laundries.  
Fibre  
Cotton  
indicating that the reserve  
function is running.  
Woollen  
Silk  
Washing the woolen textiles  
Washing the textile  
11  
 
Steps of using the operation buttons and description of the steps  
9
7
5
3
1
10  
8
Time remained(minutes)  
Reserve(hours later)  
FIBRE  
NORMAL  
QUICK  
Minutes  
Times  
Minutes  
Minutes  
6
COTTON  
4
POSTHASTE  
JEANS  
WOOLLEN  
SILK  
2
POWER  
ON/OFF  
START  
PAUSE  
PROGRAM  
SOAK  
WATER  
LEVEL  
WASH  
RINSE  
RESERVE  
SPIN  
Push the "POWER ON/OFF " button to switch on the power.  
POWER  
ON/OFF  
Push the "PROGRAM"button to select suitable automatic program.  
2
PROGRAM  
After switching on the power, the machine will set normal program automatically. Toselect other automatic  
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page  
11 for the selection.  
For instance: select "POSTHASTE" program for laundries with small  
quantity and light soil.  
Page 11  
In selecting the normal program, the machine  
Fibre  
Normal  
Quick  
Posthaste  
Jeans  
will execute fuzzy program to select water  
and wash time according to the cloth and weight  
of the laundries. The full procedure is controlled  
automatically.  
Cotton  
Woollen  
Silk  
Push the "SOAK","WASH", "RINSE" or "SPIN" button to select suitable procedure.  
Minutes  
Minutes  
Times  
Minutes  
SOAK  
WASH  
RINSE  
SPIN  
12  
 
After switching on the power, the washing machine will set to common program including"wash, rinse,  
spin "automatically. To select other procedures, push the " SOAK"," WASH", " RINSE" or "SPIN"  
button to select the time of soak,wash and spin, and the times of rinse. After switching on the power,  
if you push one of the button among "WASH", "RINSE"and"SPIN", the digitron of the former  
procedures will turn off automatically. The former procedures will not run. For instance: after switching  
on the power. If you push the "SPIN" button first, it will execute spin singly after starting.  
Attention  
.
Even there's no water in the tub, a certain period is  
required before spin starting.  
Do not use the soak program for the woolen textiles.  
Separate the laundries that are not colorfast from  
other laundries in washing.  
The pulsator will not rotate unless the water is  
filled to water level 3.  
After the machine starts operation, you can only set the program and procedure during washing, and can not  
make setting in other cases.  
The soak program can be used as fitting of normal, jeans, fibre or cotton automatic programs. It will do soaking  
with intermittent stirring of pulsator.  
Press " WATER LEVEL"button,select suitable water level  
WATER LEVEL  
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.  
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"  
button, then push the "WATER LEVEL" button to set the water level. Refer to "water level, water quantity and  
desoge of powder"in Page 10 and "WATER LEVEL"button in Page 12 for selection.  
Page 10  
Page 12  
Water Level and Time Table for Each Program (self programming not included)  
Water  
Total time(minutes)  
Wash(minutes)  
Rinse(minutes)  
Spin(minutes)  
Program  
level  
1~10  
1~10  
3
Saving water program, total about 13 minutes  
Saving water program, total about 13 minutes  
Saving water program, total about 4 minutes  
Normal  
Quick  
About 10-16  
About  
About 25-31  
About 20  
About 6  
About 2  
Posthaste  
Jeans  
Fibre  
1~10  
1~10  
1~10  
1~10  
1~10  
About 20  
About 12  
About 10  
About 3  
Rinse twice, about 5 each time  
Rinse twice, about 3 each time  
About 7  
About 5  
About 5  
About 3  
About 4  
About 54  
About 40  
About 48  
About 25  
About 30  
Rinse three times, about 3 each time  
Cotton  
Woollen  
Silk  
Rinse twice, about 2 each time  
Rinse twice, about 2 each time  
About 5  
13  
 
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by  
the water inlet pressure and water level.  
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed  
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the  
time remain digitron is the total remained time)  
* In selecting "posthaste" program, the washing machine will set the complete procedures of water level  
selectior, washing, rinsing and spinning automatically.  
* During saving water program, if the water inlet pressure is lower, the machine will come into rinse with water .  
* When selecting soak procedure, it will first soak for 10~40 minutes , then do washing , rinsing and spinning .  
Push the "reserve" button to select suitable reserve wash program  
RESERVE  
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing  
procedure to be finished at reserved time, please push the " RESERVE " button to set the reserve wash program.  
Refer to RESERVE button in Page 11 for selection.  
Page  
Confirm the operation of reserve program  
Time remained(minute)  
When the "reserve" function is activated, the indicator light of the program you have set  
will be off. The remained time will be displayed. During reserve procedure, push the  
Reserve(hours later)  
"RESERVE" button to display the reserve mode.  
To change the running program or cancel the reserve setting, you  
the washing will be finished after 18 hours.  
need to switch off the power and make new selection.  
Push the "START/PAUSE" button  
START  
PAUSE  
5 Close the lid  
As the top lid opened ,the Washer will automatically give an alarm  
and stop running , exclusively during supplying water and rinsing.  
6 Finish washing  
After finishing wash it'll switch off the power automatically.  
After Finishing wash  
alarm automatically  
14  
 
7.Disposal after washing  
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence  
your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Clean the detergent box and set it on  
the control panel seat.  
1.The method of dismantle : Push it up aslant and gently.  
2.The method of install : install it upwards and aslant  
and push it in .  
The lint filter must be used during washing.  
It must be cleaned in time after each using  
Lint filter:  
1.Pull it up to dismantle.  
2.Push it down to install.  
3.Clean the filter screen after washing.  
The back cover of lint filter  
Up  
Up  
Dismantle  
Dismantle  
Install  
Down  
Install  
Down  
The front cover of lint filter  
Dismantle  
Install  
Dismantle  
The filter screen of the water inlet valve is likely to be  
blocked by foreign materials and influence the water  
inlet.  
If the cabinet is dirty, wipe it with wet cloth  
Do not flush it directly with water.  
Wipe it with neutral detergent.  
Please clean it with brush every two months.  
Do not wipe it with thinner, petrol, alcohol etc.  
Benzene  
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).  
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.  
3.Be sure to pull off the power plug before maintenance.  
4.Hang up the power cord and drain hose.  
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time  
(about 1 hour), then close the top lid.  
15  
 
Trouble-shooting Answer to question  
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns  
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special  
maintenance department or after-sale service department of our company. Do not repair it by yourself.  
Phenomena  
The reason  
How to settle  
Close the top lid.  
The top lid is opened during reserve  
procedure.  
The digitron displays E0.  
Put down the drain hose. Open and close the  
top lid once.  
The drainage cannot work, or is too slow.  
The digitron displays E1.  
Is the drain hose put down?  
Is the drain hose blocked?  
Clean the foreign material. Open and close  
The top Lid Once.  
It stops running in midway. The digitron  
displays E2.  
Close the top lid.  
The top lid is not closed.  
Are the laundries put slantingly?  
Is the machine slanting?  
Reorder the laundries. Close the top lid.  
The machine will start running after 10  
seconds of being placed horizontally.  
The safety switch acts, and the  
spinning cannot work. The  
digitron displays E3.  
Open the water tap. Open and close  
the top lid once.  
Clean the water inlet valve then open  
and close the top lid once.  
Open and close the top lid once.  
Is the water tap opened, or is there water  
supply failure?  
Is the water inlet valve blocked?  
Is the water pressure too low?  
The water filling does not work, or is  
slow. After about 15 minutes later,  
the digital displays E4.  
Please contact the after-sales  
service department.  
The water level sensor is bad.  
The digitron displays E6.  
The power voltage is too low.  
The power voltage is too high.  
The digitron displays E8.  
The digitron displays E9.  
Not wash  
Pull off the power plug. Wait for the  
voltage resuming normal before usage.  
Is there power failure?  
Is the power plug inserted tightly?  
Is the water level reached preset position?  
Please use it when there's power supply.  
Insert the power plug tightly.  
Fill water to the preset position.  
The machine does  
not act  
Insert the power plug tightly.  
Close the top lid.  
Set the laundries flat.  
Is the power plug inserted tightly?  
Is the top lid closed reliably?  
Are the laundries set flat?  
Not spin  
Is the machine slanting?  
Are the laundries put slantingly in spinning?  
Are there any foreign materials?  
Adjust the machine to be even  
Reorder the laundries and close the top lid.  
Remove the foreign materials.  
There's abnormal sound  
inside the machine  
Is the screw of the jointer of water  
inlet hose loose or awry?  
The water tap leaks  
Fasten the screw of the jointer properly.  
Common phenomena  
Phenomena  
Explanation  
Balance the laundries to avoid slanting.  
The spinning is intermittent when it starts.  
The wash procedure pauses.  
The cloth sensor is detecting , it will add water after about 48 senconds  
The program is setting the drain time , certain  
period is needed before it starts spinning.  
Select spin program, but it does not work.  
There may be some water flowing out of the  
drain hose in the first use of the machine.  
It is the water remained performance inspection  
by the factory.  
16  
 
Packing list  
Quantity  
One  
Name  
User's manual  
Inner cover  
components  
One  
One  
Component of the  
water inlet hose  
The end connecting to  
the washing machine  
Jointer connecting the  
water inlet hose and  
the water faucet  
The end connecting to the  
water inlet hose jointer  
One  
Bottom cover  
Topping screws  
Eight  
One  
Full automatic washing machine  
Specification  
Water level/Water  
1/18L 2/24L 3/30L 4/36L 5/42L 6/48L 7/54L 8/60L 9/66L 10/70L  
quantity (about)  
Water Injection pressure  
0.03MPa 0.78MPa  
Rated washing /  
7.0kg/7.0kg  
spinning capacity(kg)  
17  
 

Graham Field Blood Pressure Monitor 707A INS LAB RevD11 User Manual
Grizzly Planer G9003 User Manual
Hamilton Beach Beverage Dispenser 840116400 User Manual
HANNspree Car Video System HF289 User Manual
Harbor Freight Tools Washer Dryer 92336 User Manual
Harman Kardon CD Player HD710 User Manual
Harman Kardon Home Theater System DPR 1001 User Manual
Hotpoint Dishwasher FDLET 31020 User Manual
HP Hewlett Packard Network Card BL685c G5 User Manual
IBM Switch BDM 610000049 User Manual