Full automatic washing machine
User's manual
This manual is for
XQB50-68
Special number 0030506438
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Top lid
Water level knob
Detergent box
Power switch
Water inlet valve
Power wire
Lint filter(Installed by user)
Cabinet handle
Control panel seat
Water
channel
Filter cover
Inner tub
Drain hose
Front control board
Control panel sheet
Drain hose
hanging hole
Pulsator
Cabinet
Front fixed foot
Drain outlet
protecting cover
Drain hose bushing
Back cover
Rear fixed foot
Adjustable foot
Adjustable foot seam
Meaning and description of the symbols
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Warning sign
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
Forbidding sign
Please check if the power receptacle has good earthing
condition before using to guarantee your safety.
Safety precautions
Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please
adopt electric leakage protector.
When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned orwhen it
is idle.
Earth
If the power cord is bad, to avoid risk it is required to replace it by the
technicians ofour special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp
Do not use water hotter than 50 C .
place like the bathroom . Never
wash it with water. Do not place
wet laundries on the control panel.
In case the washing machine is in-
stalled on ground with carpet, do not
block the ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
The ventilation holes
at the bottom
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Safety precautions
Do not stretch hands into the working
Do not decompose, repair or alter the
machine by yourself.
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
l
tro
r
e
Pe
inn
h
T
Keep the machine away from direct
sunlight and heat source like the heater.
The handicapped or children without
care shall not use the machine.
To prevent the lint inside the tub from
blockingthe cascade outlet during
washing, please keep the lint filter in
good condition, and install it to proper
position. If the lint filter is lost or da-
maged, please contact the local after-
sales service department of our company.
To protect your laundries and wash-
ing machine, please take out all of the
coins, buttons, sand, hairpin and
other foreign materials before washing.
Please check if the water faucet is open,
and if the connection of the water inlet
pipe is proper.
It is suggested to use foamless washing
powder.
Install
Dismantle
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Install the bottom plate
After you open the package, please lean
the washing machine gently down on soft
Back
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine with the eight screws by
a cross screwdriver, then lift the machine
up gently. See to the figure:
Front
Bottom plate
Soft items
Screw
Adjust the installation position
The largest allowed slope of the base of the machine is 2 . The slanting or rough
ground will result in unstable running or stoppage of the machine. Please adjust
it with following methods:
Confirm it's horizontal:
Hang the lead line to confirm if it is horizontal.
Adjust the adjustable foot:
1.To twist the adjustable foot, please first lift up the side of the foot slightly, loosen
the adjustable nut, and twist the foot.
2.Fasten the nut after adjustment.
Adjustable nut
Fasten
Loosen
High
Adjustable foot
Low
Install the lint filter
After opening the package, please take out the lint
filter from the document bag, install it to the
inner tub. See to the figure.
Install
How to change the direction of the drain hose
1.Dismantle the back cover of the washing
machine.
3.Dismantle the protecting cover of the
drain outletat the other side (method
the same as the bushing). Install the
bushing as per indicated in Figure 4.
2.Put down the drain hose. Take off the
drainhose frame. As indicated in Figure
1, put thedrain hose into the cabinet.
Then stretch onehand into the cabinet
to nip the claw of the drain hose bush-
ing to remove the claw fromoriginal
position. Take off the drain hose bush-
ing with the other hand. (As indicated in
Figure 2 and 3).
4.Extend the drain hose from the other
side. Fix thedrain hose onto the base
frame with the drain hoseframe. (As
indicated in Figure 5)
Drain outlet
protecting cover
Outer
drain
hose
Drain hose bushing
Drain hose bushing
Drain hose frame
Figure 1
Figure 2
Figure 4
Figure 5
Cabinet
5.Install the protecting cover of the drain
outlet at the other side as per indicated
in Figure 6.
Inner Outer
Press
Drain hose
bushing
Take off
Drain hose
bushing claw
Press
Figure 3
Figure 6
Usage of the drain hose
Before using , hang up the drain hose on suitable location.
Do not put down the drain hose on the ground.
Confirm the end of drain hose is higher than
the level of tub . If not the siphon will being .
<1.2m
Install the water inlet hose
Confirm the water faucet
Water faucet, not suitable
Water faucet, suitable
It is required that the front end shall be longer than 10cm.
The outlet end surface of the faucet shall be flat and smooth. If not please file it to
avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the
water inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the
water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and
the jointer can not be set on the water faucet, please loosen the four screws
and take out the bushing in the jointer. The front end of the faucet must be
smooth, otherwise it may leak water. See to Figure 3.)
Water inlet hose jointer
Screw
Slider
Lock lever
Nameplate
Screwdriver
Bushing
Water inlet hose
Figure 1
Figure 2
Figure 3
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the
figure to seal up the outlet end surface of the faucet. See to Figure 5.
Remarks:
Before installation, the threading is 4mm above the upper surface of the
nut. After installation, the threading is 2mm above the upper surface of the nut.
About 4mm
See to Figure 6.
before twisting;
about below 2mm
after twisting
Nut
Figure 6
Figure 4
Figure 5)
Connection between the water inlet hose and the washing machine
1.Do not take off the water absorption cushion.
Nut of the water I
nlet hose
Please check if the cushion is dropped or
damaged before each usage. If it happens
please contact our after-sale department
immediately.
2.Put the nut of the water inlet hose on the
valve jointer.
3.Fasten the nut. Swing it gently to confirm
if it's suitable.
Water absorption cushion
Jointer of the
water inlet valve
Connection between the jointer of the water inlet hose and the water inlet hose
1.Push down the slider. Insert the water inlet
Jointer of the
hose into the jointer.
2.Hang the lock lever to the jointer. Release
the slider till a click sound is heard.
water inlet hose
Locking lever
Slider
Check the connection between the jointer of the water inlet hose and the water faucet
1.Swing the hose gently to confirm if it is fastened
stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Each time before use please check if the
connection between the jointer of the water inlet
hose and the water faucet, and the installation
of the water inlet hose are firm, so as to prevent
dropping from improper installation position.
Dismantle the water inlet hose
1.Close the water faucet.
2.Press the locking lever. Push down the slider.
Then pull off the water inlet hose. If the machine
is used more than once every week, the jointer
of the water inlet hose can be kept on the faucet
to prevent damaging the fixing screw.
Locking lever
Slider
1Preparation before washing
Preparation before washing
1.Connect the water inlet hose. Open
the water faucet.
2.Confirm that the washing machine is
earthed reliably. Then insert the
power plug into the receptacle. The
earth terminal shall not link to gas
pipeline and faucet water pipeline.
3.Hang up the drain hose.
<1.2m
Pay attention to followings before washing the laundries
Check if
The quantity of
When the pulsator
Clear the
Tie the long
strips; fasten
the buttons;
close zippers.
the laundries
has special
requirement
on washing
the laundries is running , the
shall not be too buttons of the
large. Stretch laundries may
and loosen the cause noise. For
laundries before the sake of
pocket. Take
out the coins,
sand, hairpins
etc.
putting them in discretion, please
the tub.
put the laundries
with buttons into
other laundries.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
2 Put in the laundries
The capacity of washing and spinning of
the machine refer to the largest weight of
the standard laundries under dry condition
that can be washed or spinned in one time.
One time washing quantity shall be lower
than the rated capacity.
The thickness, size, type of the cloth will
influence the actual washing capacity. It is
suitable for one time washing to put in
reasonable amount of laundries and the
laundries can be turned round in washing.
Do not select "High"water level for laundries
small than 1.0kg, so as to avoid splashing
of water.
3 Add the detergent
How to use the washing powder
Direct dissolved in the machine
1.Fill water to "Low" water level.
2.Add the power. Run for 30 seconds to
dissolve it completely.
3.Put in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
How to use the whitener
1. Prepare warm water of 30
container.
2. Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high sudsing
detergent.
Different washing powders have different
dosage. Please refer to the usage manual
of the washing powder for the details.
and a
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on laundries
with color or pattern as they are
prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for the
usage and quantity of the whitener.
For powder whitener, please dissolve
it before use.
4 Use the operation knobsand buttons
a Description of the function of the knobs and buttons
Mode and meaning of the indicators
Flashing: indicate the running program
On: indicate the program about to run, or indicate the selected mode
Flashing rapidly: indicate abnormal condition
Start
Process
Selection
Pause
Spin
Quick-
wash
Twice-
wash
Rinse
Wash
"Process selection” button
One or more out of the five process programs
are available for your option: quick- wash, twice-
wash,wash, rinse, spin
"Start/Pause" button
After the power is switched on, push it
to start the machine
During working, push it to pause
working.
During pause, push it to resume
working.
b .Steps of using the operation buttons and description of the steps
"Power" botton
Push the "Power" button to
switch on or off the power.
When the power is on, push it
again to switch off the power.
Start
Process
Pause
Selection
Quick-
wash
Spin
Rinse
Twice-
wash
Wash
Power
Auto off
Water Level
Low
Medium
High
Reset
On
Off
Power
Low
Auto off
Medium
High
Reset
On
Off
"Water Level " button
Select or adjust the water level.
1 Push the "Power “ button to switch on the power
ON
OFF
Process
Selection
2 Push the "Process Selection" button to select
the suitable process
After switching on the power, the machine will set to standard program automatically
including " wash-rinse-spin ". To select other program, push the "Process Selection"
button to select one or more programs among "Quick- wash" "Twice- wash" "Wash"
"Rinse" "Spin". Refer to the "Selection method of the procedure programs " for the
selection.
Page 12
Attention
Even there's no water in the tub, the
spinning will start after a certain period.
Do not use the "Twice wash" program
for the woolen laundries.
Wash the laundries that are prone to
lose colors separately from other laundries.
The pulsator will not rotate unless the water is filled to selected water level.
Selection method of the procedure programs
Times of pushing
the "Process
Selection" button
Contents (the lighted indicators
indicate the programs about to run)
Selected procedure
program
Applicable procedure
Quick- Twice-
Wash rinse spin
wash wash
When the common laundries
need washing , rinsing and
spinning
Wash, rinse, spin
(standard program)
Wash (the washing
liquid remains in
the tub)
Quick- Twice-
Wash rinse spin
wash wash
Repeat using the washing
liquid
Quick- Twice-
Wash rinse spin
wash wash
Wash, rinse ( the
rinsing liquid remains
in the tub)
Repeat using the washing
liquid
Quick- Twice-
Wash rinse spin
wash wash
When the laundries need
rinsing and spinning after
manual washing
Rinse, spin
When the laundries need
only spinning after manual
washing (first drain then spin)
Quick- Twice-
Wash rinse spin
wash wash
Spin
(spin after drain)
Quick- Twice-
Wash rinse spin
wash wash
If the laundries are very dirty,
or the sleeve and collar are
dirty, first soak then wash
Twice-wash, wash,
rinse, spin
Quick- Twice-
Wash rinse spin
wash wash
Quick-wash, wash,
rinse, spin
When quickly wash the
light dirty laundries.
If you push the "Process Selection" button for 7 times, it will resume the original mode, and
it will circulate like that.
If you select the "Quick wash" program, you have to set the full procedure of wash, rinse
and spin. The procedure cannot be selected.
* Total time: including the normal water inlet time, drain time, excluding the power off
time. The total washing time may be influenced by the water inlet pressure and
water level.
* Spin time: the time from intermittent running to finishing
* When selecting " Twice-wash " program, first soak for about 20 minutes, pre-wash
for about 8 minutes, then soak for about 5 minutes, then do washing, rinsing and
spinning. The wash time in the list includes the pre-wash time.
3.Adjust the "water level “ knob to select suitable water level
Three water levels available according to the laundries quantity: High; Medium; Low.
Page 11
After the water inlet as per the preset water level, in case additional water
quantity is required, please first set the button to the "Reset", push and hold it
to perform automatic water inlet. When it reaches the suitable water level, you
can turn it to the needed water level.
After the water inlet under set water level, if higher water level is needed, please
first turn the knob to " Reset ", then turn back to needed water level. The wash-
ing machine will fill water to the new water level.
4 Press the "Start/Pause" button
Start
Pause
6 The washing is finished
5 Close the top lid
When the washing is finished, the
three indicators of "Wash" "Rinse"
"Spin" are all on.The power will be
switched off automatically about 10
minutes after the finishing of the
washing.
If you open the top lid, the machine
will stop working before spinning
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during
washing.
It must be cleaned in time after each
using
Lint filter:
Clean the detergent box and set it on
the control panel seat.
1.Pull it up to dismantle.
2.Push it down to install.
3.Clean the filter screen after washing.
Install
Dismantle
Clean
If the cabinet is dirty, wipe it with wet cloth
The filter screen of the water inlet valve is
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.
likely to be blocked by foreign materials
and influence the water inlet. Please clean
it with brush every two months.
l
er
Petro
Thinn
Alcohol
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely
after each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid
for some time (about 1 hour), then close the top lid.
Trouble-shooting Answers to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending it
to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do not repair it by yourself.
Phenomenan
The reason
How to settle
In spinning, the machine stops
running. (The "wash" "rinse"
"spin" indicator flash quickly)
Close the top lid.
The top lid is not closed.
The draining does not work,
or the speed of draining is
too slow ( the indicators of
"rinse" "spin" flash)
Is the drain hose blocked
by foreign material?
Clean the foreign material.
Open and close the top lid once.
The safety switch acts. The
spinning can not work (the
indicators of "wash" "rinse"
flash quickly)
Are the laundries put
slantingly?
Is the machine slanting?
Re-order the laundries.
Close the top lid.
Level the machine in right position.
Open and close the top lid once.
Open the water faucet. Push
the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
The water faucet is not open.
The program pauses after
about 15 minutes of water
inlet (the indicators of "wash"
"spin" flash quickly)
The water inlet valve is
blocked
Wait for the normal water
pressure before use.
The water pressure is too low
and the current is too small.
Is there power failure?
Is the power plug loose?
If water level reach the appoint level?
Use it when the power is on.
Insert the power plug tightly.
No wash
Affusion to appoint level.
The machine does
not act.
Insert the power plug tightly.
Close the top lid
Is the power plug loose?
Is the top lid is not closed.?
No spin
Re-order the laundries.
Close the top lid.
Are the laundries put
slantingly?
There's abnormal sound
inside the machine.
Is the machine slanting?
Are the laundries slanting
in spinning?
Level the machine properly.
Re-order the laundries.
Is the jointer screw of the
water inlet hose is loose
or twisted awry?
The water faucet leaks.
Fasten the jointer screw
properly.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The program is setting the drain time. Some
time is needed before it starts spinning.
Push the "Process selector" button to
select "Spin", but it doesn't work.
There may be some water flowing out of
the drain hose in the first use of the machine.
It is the water remained in the factory
inspection of performance.
It is because that the laundries are slanting
to one side, and the safety switch acts. After
water inlet and stirring, the slanting will be
removed and the spinning will work.
In the final spinning, it stops and displays
"Rinse", and starts water inlet.
Paching list
Name
Quantity
User's manual
One piece
One piece
Certificate of warranty
Components of the
water inlet hose
The end connecting to
the washing machine
Jointer connecting the
water inlet hose and
the water faucet
One piece
The end connecting
to the water inlet hose
jointer
Bottom plate
One piece
Tapping screws
Lint filter
Egiht pieces
One piece
One set
Full automatic
washing machine
Specification
Water level/Water quantity (about)
High/52L, Medium/43L, Low/30L
5.0 (weight of standard dry cloth)
Injection pressure(MPa
Rated washing / spinning capacity(kg)
|