Full Automatic Washing Machine
User's manual
This manual is for
HWM90-96A
Please read this manual carefully
before using.
Retain it for future reference.
0030807216
Trouble-shooting answer to question
Before Using
Names of the parts
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Honourable users:
Thank you for choosing our products.
Our products integrate high-tech, precision, frontier science .To facilitate using it,
please read this manual carefully and operate this machine according to it.
Phenomena
The reason
How to settle
Buzzing upon reservation starts,
Nixie tube indicates "E0"
The top lid is not closed
Close the top lid
Top lid components
Water absorption cushion
Power cord
Rear faceplate
Water inlet valve
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Is the drain hose put down?
No or slow drain, nixie tube
indicates "E1" , buzzing.
Is the drain hose blocked by
foreign material?
Detergent box
Control panel
Outer tub cover
Balance ring
Running pauses during spin,
nixie tube indicates "E2",
buzzing
The top cover leaves open
Close the top lid
Draining hose
hanging hole
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Are the laundries put slantingly?
Is the machine slanting?
Safety switch actuates, not
spin, (after self-correction
twice), nixie tube displays
"E3", buzzing
Inner tub
Open and close the top lid once.
Lint filter(2pieces)
Pulsator
Open the water tap. Push
the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
The water tap is not open
Control panel coating
Cabinet
No or slow water filling (not
reaching the level in 40 min),
nixie tube indicates "E4",
buzzing
The water inlet valve is blocked
The water pressureis too low
and the current is too small
Handle
Liquid wahitener inlet
Drain hose
Back cover
Please contact the after-sales
service department.
The water level sensor is bad.
The digitron displays E6.
Adjustable leg
Poor or no waterfall flow
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
Is there power failure?
Is the power plug loose?
Use it when the power is on.
Meaning and description of the symbols
Insert the power plug tightly.
Affusion to the set water level.
Accessories
Not wash
The machine does
not act
Does the water level arrive at the
set water level?
Contents marked with that symbol
are related to the safety of the
product and the personal safety
of the users. Please operate in strict
conformity to the contents, otherwise
it may result in damage of the
machine or influence the personal
safety of the users.
Is the power plug loose?
Is the top lid closed?
Insert the power plug tightly.
Close the top lid
Not spin
Bottom plate
(One piece)
Are the laundries put orderly?
Put the laundries orderly.
Is the machine slanting?
Level the machine properly.
Re-order the laundries.
There's abnormal sound inside the
machine
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Fasten the jointer screw
properly.
The water faucet leaks
the end connecting to
the washing machine
jointer connecting the water
Water inlet hose
(One piece)
inlet hose and the water faucet
Contents marked with that symbol
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or influence the personal safety
of the users.
Common phenomena
Phenomena
Water inlet hose jointer
Explanation
(One piece)
the end connecting to the
water inlet hose jointer
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure pauses.
The cloth sensor is detecting , it will add water
after about 48 senconds.
Tapping screw
(Eight pieces)
The program is setting the drain time , certain
period is needed before it starts spinning.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
The figure in this manual being sketch map and with the improvement of our products, the machine you buy
is like to be different from the figure indicated in the manual .Please understand.
16
1
Safety precautions
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence
your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Before Using
Using process
Please plug the power plug on special
The washing machine must be positioned
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle : Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
Earth
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.
The cover oflint filter
lint filter
lint filter
Install
Dismantle
The back cover of lintfilter
Dismantle
Install
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
The ventilation
holes at the bottom
Dismantle
Install
Soft object
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
Benzene
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged,please contact the local
after-sales service department of our company.
To prevent your laundries and washing machine from
damages, be sure to take out all of the foreign materials
from your pocket, such as coins, buttons, sandor hair
pins etc.
4.Hang up the power cord and drain hose.
The cover of lint filter
lint filter
lint filter
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time (
about 1 hour), then close the top lid.
Install
Dismantle
Before washing, please check if the water tap is open,
and if the water inlet pipe is connected properly.
The back cover of lint filter
Dismantle
Install
It is suggested to use low-foaming washing powder.
2
15
Safety precautions
Before Using
Using process
Do not decompose, repair or alter the machine
by yourself.
Do not stretch hands into the working machine.
It is dangerous even if the rotation is slow.
Take special care of the children.
* Total time: including the normal water inlet time and drain time. The total washing time may be influenced by
the water inlet pressure and water level.
* Spin time: From the moment the intermittent spinning starts to the moment it stops running (the time displayed
on spin digitron is from intermittent spinning to the moment before inertia spinning; the time displayed on the
time remain digitron is the total remained time)
* During saving water program, if the water inlet pressure is lower, the machine will come into rinse with water .
* When selecting soak procedure, it will first soak for 10~40 minutes , then do washing , rinsing and spinning .
Push the "reserve" button to select suitable reserve wash program
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Do not put any hot or heavy items (such as the kettle
with hot water) on the washing machine
RESERVE
After switching on the power, the reserve program is set to off mode automatically. If you need to set the washing
procedure to be finished at reserved time, please push the " RESERVE " button to set the reserve wash program.
Refer to RESERVE button in Page 11 for selection.
Benzene
TIME REMAINED(MINUTE)
Page
RESERVE(HOURS LATER)
The appliance is not instruct for use of
young children of infirm persons without
supervision.Young children should be
supervised to ensure that they do not
play with the appliance.
Push the "START/PAUSE" button
Keep the machine away from direct sunlight and
heat source like the heater.
START
PAUSE
Attention
.
After the program starts running ,the buttons are not selected execpted the water level and start/pause button
If you open the top lid during the runningprogram, The digitron displaysE2
Installation and adjustment
5 Close the top lid
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
As the top lid opened ,the Washer will automatically give an alarm
and stop running , exclusively during supplying water and rinsing.
Install the bottom plate
6 Finish washing
After opening the package, please lean
Back
After finishing wash it'll switch off the power automatically.
the washing machine gently down on
soft items (like towel cloth, blanket, etc.).
Install the bottom plate to the bottom
of the machine with eight screws by a
c r o s s s c r e w d r i v e r, t h e n l i f t t h e
machine up gently. See to the figure:
Front
After Finishing wash
alarm automatically
Bottom plate
Soft items
Screw
3
14
Before Using
Using process
Adjust the Installation position
The largest allowed slope of the shank base of the machine is 2 . The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
Confirm it's horizontal
After switching on the power, the washing machine will set to standard program including"wash, rinse,
spin "automatically.To select other procedures, push the "SOAK"," WASH"," RINSE"or "SPIN"button to
select the time of soak,wash and spin, and the times of rinse. After switching on the power,if you push
one of the button among "WASH", "RINSE"and"SPIN", the digitron of the formerprocedures will turn off
automatically. The former procedures will not run. For instance: after switching on the power. If you push
the "SPIN" button first, it will execute spin singly after starting.
Hang the plumb to confirm it's horizontal
Adjust the adjustable foot
(1) To twist the adjustable foot at the right front of
the cabinet (front the sight of front), please first
lift up the side of the foot slightly, loosen the
adjustable nut, and twist the foot.
(2) Fasten the nut after adjustment.
adjustable nut
adjustable foot
Loosen
Fasten
High
Low
Attention
How to change the direction of the drain hose
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
1.Lean the machine down gently with the front
surface facing the ground. Loosen the eight
screws by a cross screwdriver.
3.Extend the drain hose from the right side. Push the
drain hose into the groove with hands.
Back
The pulsator will not rotate unless the water is
filled to water level 3.
Bottom plate
Front
After the machine starts operation, you can only set the program and procedure during washing, and can not
make setting in other cases.
Soft item
The soak program can be used as fitting of common, carpeting,nomarl or cotton automatic programs. It will do soaking
with intermittent stirring of pulsator.
2.Pull out the drain hose from the groove at the left side.
Use groove at
this side after
direction changing
Press " WATER LEVEL "button,
select suitable water level
4.Install the bottom plate (as per indicated before),
then lift the machine up gently.
WATER LEVEL
Page 3
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level. Refer to "water level, water quantity and
desoge of powder"in Page 9 and "WATER LEVEL"button in Page 11 for selection.
Usage of the drain hose
The drain hose shall drain smoothly
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Page 11
Page 9
Water Level and Time Table for Each Program (self programming not included)
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
Total time(minutes)
Wash(minutes)
Rinse(times)
Spin(minutes)
Program
About 4
About 5
About 1
About 5
Rinse twice, about 2 each time
Rinse twice, about 5 each time
Rinse once, about 3 each time
Standard
Dry-cleaning
Save
About 12
About 15
About 3
About 15
About 5
About 10
About 6
About 30
About 51
About 12
About 72
Blanket
Rinse twice, about 5 each time
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
5.If the extra hose is too long, cut it
either at A or at B point.
Rinse twice, about 2 each time
Rinse twice, about 3 each time
About 2
About 3
About 30
About 56
Silk
Cotton
Woollen
Rinse twice, about 2 each time
About 37
About 1
13
4
Install the water inlet hose Before Using
Using process
Steps of using the operation buttons and description of the steps
Confirm the water faucet
water faucet, suitable
water faucet, not suitable
TIME REMAINED(MINUTE)
The exit end face of the faucet
DRY-CLEANING
SILK
STANDARD
SAVE
MINUTES
MINUTES
MINUTES
TIMES
COTTON
BLANKET
RESERVE(HOURS LATER)
(18L)
MIN
HWM90-96A
Digital tub display
TUB CLEAN
WOOLLEN
nano wash
10 water level selection
12 mins quick wash
POWER
ON/OFF
START
PAUSE
Super-power digital
intelligent control
+
SOAK
WASH
RINSE
SPIN
PROGRAM
RESERVE
WATER LEVEL
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Push the "POWER ON/OFF " button to switch on the power.
POWER
ON/OFF
2 Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise
it may leak water. See to Figure 3.)
Push the "PROGRAM"button to select suitable automatic program.
2
PROGRAM
water inlet hose jointer
After switching on the power, the machine will set standard program automatically. To select other automatic
program, push the "program" button till the relative indicator is on. Refer to the "program button" on Page
11 for the selection.
Screw
Slider
For instance: select "SAVE" program for laundries with small quantity
and light soil.
Nameplate
Page 11
Bushing
Lock level
Screw knife
water inlet hose
Figure 1
Figure 2
Figure 3
In selecting the standard program, the machine
DRY-CLEANING
SILK
STANDARD
SAVE
will execute fuzzy program to select water
and wash time according to the cloth and weight
of the laundries. The full procedure is controlled
automatically.
3.Fasten the four screws evenly. See to Figure 4.
COTTON
BLANKET
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
TUB CLEAN
WOOLLEN
Remark: .Before twisting the fastening nut, the threading is 4mm above the upper
surface of the nut. After twisting, the threading is less than 2mm above the upper
surface of the nut. See to Figure 6
Push the "SOAK","WASH", "RINSE" or "SPIN"button to select suitable procedure.
MINUTES
MINUTES
TIMES
MINUTES
about 4mm after twisting
About above 2mm after twisting
Screw nut
H
WAS
RINSE
SPIN
SOAK
Figure 4
Figure 5
Figure 6
12
5
Before Using
Using process
Connection between the water inlet hose and the washer
Child lock function
Power On/Off button
This function is used to protect the children and prevent them from changing the washing
procedure.
button to switch on
s on, push it again
Push the POWER ON/OFF
the power. When the power i
to switch off the power.
1.Do not take off the water absorption cushion. Please check if the
cushion is dropped or damaged before each usage. If it happens
please contact our after-sale department immediately.
nut of the water inlet hose
Start up:The program is optional anytime after the machine has been starded.Push and hold the
WATER LEVEL button and SPIN button for more than 3 seconds at the same time.After a
beep sound,the child safety lock program works;all buttons are locked and cannot be selected.
During this period, when open the top lid, the machine will give a beep alarm. 15 seconds later
,no matter opening or closing the top lid, the machine goes on alarming and drains water.After
draining, 10 minutes later power off automatically.
utton to switch on
E button is not
will automatically
Push the POWER ON/OFF b
the power. If the START/PAUS
pushed, the washing machine
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
inutes.
switch off the power after 5 m
jointer of the water inlet valve
water absorption cushion.
Release:push and hold WATER LEVEL button and SPIN buttonfor more than 3
seconds at the sametime.After a beep sound,the child safety lockprogram is
released;all buttons are unlocked.
Connection between the jointer of the water inlet hose
and the water inlet hose
Reserve/remain time indicator digitron
During sensing, it displays --
During reserve procedure, it displays the remained reserve time (in hour)
During operation of programs, it displays the remained time (minute). If the remained time exceeds 99 minutes,
1.Push down the slider. Insert the water inlet hose into the jointer.
it adopts A at tens place to represent 100 minutes, b to represent 110 minutes. For instance, A3 represents 103 minutes.
Page 16
In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16)
the jointer of the water inlet hose
Slider
2 Hang the lock lever to the jointer. Release the slider till a click sound is heard.
Locking level
TIME REMAINED(MINUTES)
RESERVE(HOURS LATER)
STANDARD
SAVE
DRY-CLEANING
SILK
COTTON
BLANKET
TUB CLEAN
WOOLLEN
(18L)
MIN
POWER
Check the connection between the jointer of the water inlet hose
and the water faucet
START
PAUSE
ON/OFF
PROGRAM
RESERVE
WATER LEVEL
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
Start/Pause
After the power is switched on, push it to
button
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
Start the machine
During working, push it to pause working.
During pause, push it to resume working.
WATER LEVEL button
RESERVE button
If the standard program,the washing machine can detect
the laundries automatically.After detection, it will set the water
level to suitable value among 4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push
the START/PAUSE button to make new setting.
In standard operation mode,
the reserve indicator light
is off. The time remain
PROGRAM
selectio
n butto
n
Following automatic programs are available for selection
indicator light is on. The
digitron displays the time
remained (in minute) before
the washing is finished.
Push down the RESERVE
button. The digitron displays
the reserve time of finishing
washing(in hour).When the
machine is started, the
reserve indicator light is on,
indicating that the reserve
function is running and other
lights are off.
Program
Standard
Applicable situation
Common washing
Dismantle the water inlet hose
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .
Quick and high-efficiency wash for
common laundries
Save
If wet laundries are put in, it may display water level 10 . You
must set suitable water level by yourself.
1. Close the water faucet.
Blanket
Washing the relatively big and thick laundriesr
Washing the woolen textiles
If SAVE program is selected, it will display water level 2 .the
2. Press the locking lever. Push down the slider. Then pull of the water inlet hose.
If the machine is used frequently, the jointer of the water inlet hose can be kept
on the faucet to prevent damaging the fixing screw.
water is never to be changed,When water level
in water filling, it will perform washing while filling water. When
water level is reached,it will change to standard washing.
2
is reached
Woollen
Locking level
Slider
Washing for laundries requiring dry-clean
(see to dry-clean description and No.12
of the points of attention for details)
3
Dry-cleaning
During the program of the woolen or the dry-cleaning , it will
display water level 10 .the water level is selected from 8 to10;
During operation of wash and rinse program, you can push
down the water level button to add water. When you release
the button, or it reaches the overflow water level, the machine
will stop adding water . The water level decided may be
different from actual value because of the different moisture
level of the laundries.
Silk
Washing the textile
Remarks: use the new hose sets supplied with the washer.
Any other old hose sets should not be used.
Cotton
Washing the cotton textiles
Avoid growing mildew on the outer tub
Tub clean
and the inner tub
6
11
4 Use the operation buttons
Using process
Description of the function of the buttons
1 Preparation before washing
Using process
Preparation before washing
Mode and meaning of the indicator
Digital tube
1.Connect the water inlet hose. Open the water faucet.
2.Confirm that the washing machine is earthed reliably.
Then insert the power plug into the receptacle. The
earth terminal shall not link to gas pipeline and faucet
water pipeline.
During sensing, it displays "--"
the frame of the indicator is on : indicate the program about to run,
or indicate the selected mode
During operation of programs, it displays the
remained time (minute) or remained times of
the corresponding procedure
The digital tube corresponding to the running
program lights.
3.Put down the drain hose.
Attention
During the machine works,allbuttons except LEVEL
button and START/PAUSE button unselect.
During the machine works,openingthe top lid themachine
will give a beepalarm.
Pay attention to the followings before washing
MINUTES
MINUTES
TIMES
MINUTES
The quantity of
When the pulsator
is running, the but-
tons of the laundri-
es may cause noi-
se. For the sake of
discretion, please
put the laundries
with buttons into
other laundries.
Check if the
Tie the long
Clear the pocket.
HWM90-96A
Digital tub display
10 water level selection
12 mins quick wash
Pay attention to followings before washing the laundries
nano wash
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
laundries has
special requi-
rement on w-
ashing
strips; fasten
the buttons;
close zippers.
Take out the coi-
ns, sand, hairpins
etc.
Super-power
d
igital intellig
ent control
+
WASH
RINSE
SOAK
SPIN
RINSE button
SOAK button
WASH button
SPIN button
Push the SPIN Button to
set the spin
Push the RINSE button to set the rinse
procedure.
Push the SOAK button to set
the soak procedure.
Push the WASH button
to set the wash procedure.
During standard and blanket
programs, push the WASH
button to set different wash
time (from 0 to 25 minutes)
During cotton woollen and silk
programs, push the WASH
button to select wash
During standard and blanket
programs, pushthe SPINbutton
to setdifferent spin time
During standard and blanket programs,
push the RINSE button to set different
rinse times ( 0, 1,1., 2,2., 3,3., 4,4. Times),
when display (1.,2.,3.,4.),the first rinse is
overflowing.
During standard and blanket
programs, push the SOAK
button to set different soak
time (10,20,30 or 40 minutes)
During cotton programs, push
the SOAK button to select
soak procedure, but the soak
time can not be changed.
During otherd programs, push
the SOAK button, the machine
have no reaction.
(from 0 to 9 minutes)
During cotton, woollen and
silk programs, push the SPIN
spin procedure,
button to select
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust.
For the parts with heavy soil, please apply detergent on them in advance, which
can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before
putting in.
f. Do not put those laundries polluted by chemicals into the washing machine directly.
but the spin time can not be
Changed.
During cotton woollen and silk programs,
push the RINSE button to select rinse
procedure, but the rinse times can not
be changed.
During the other program,
push the SPIN button, the
machine have no reaction
procedure, but the wash time
can not be changed.
During other programs,push the RINSE
button, the machinehave no reaction.
During otherprograms, push
the WASHbutton, the machine
have no reaction.
10
7
2 Put in the laundries
3 Usage of the detergent
Using process
Using process
Add the washing powder or softener into the detergent box
directly as indicated in the left figure.
The capacity of washing and spinning of the machine
refer to the largest weight of the standard laundries
under dry condition that can be washed or spinning
in one time. One time washing quantity shall be lower
than the rated capacity. The largest capacity of this
machine is 9.0kg.
Washing powder inlet entrance
Softener inlet entrance
After adding washing powder ,please close the detergent box.
See to following table for the dosage of the washing
powder.
How to use the washing powder
The thickness, size, type of the cloth will influence the
actual washing capacity. It is suitable for one time
washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.
Direct dissolved in the machine(not applicable for fuzzy
and reserve programs)
Do not select above 4 water level for laundries small
than 1.0kg, so as to avoid splashing of water.
1.Fill small quantity of water.
How to use the whitener
2.Add the power. Run for 30 seconds to dissolve
it completely.
Fill water to decided level .Dilute the whitener with
container. Pour it slowly into the washing tub.
3.Put in the laundries. Select suitable water level.
Avoid using whitener on laundries with colour or
pattern as they are prone to lose colour.
Reference weight of the laundries:
The instant dissolving of the washing powder:
1. Prepare warm water of 30 and a container.
2. Add the powder while stirring to fully dissolve it.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and
quantity of the whitener.
working suit up,down
cotton,about 1120g
It is suggested to use liquid detergent when you
use SAVE WASH.
jeans about 800g
For powder whitener, please dissolve it before use.
blanket
cotton,about 900g
How to use softener
Please add the powder according to the laundry quantity,
water level and water quantity.
When you use softener, the softener must
be lower than the underside of water cap.
Please often wash the detergent box,because
softener may curdle easily.
blending coat
about 800g
It is suggested not to use high sudsing detergent.
pajamas
about 200g
Before use softener,you must select to disinfect
clothes.
Water level, water quantity and dosage of the washing powder
jacket
cotton,about
800g
shirt
cotton,about
300g
Common powder
(add 40g in each 30L water)
Concentrated powder
(add 30g in each 30L water)
Laundry quantity(kg)
Water level
Water quantity
About 68L
About 63L
About 93.3g
About 88g
About 58.3
About 55g
g
single bed sheet
cotton,about 600g
About 56L
About 50L
About 80g
About 72g
About 50g
About 45g
About 45L
About 41L
About 64g
About 56g
About 40g
About 35g
undershirt
cotton,about 180g
socking
blending,about 50g
underpants
cotton,about 70g
About 37L
About 32L
About 48g
About 40g
About 30g
About 25g
About 28L
About 23L
About 32g
About 24g
About 20g
About 15g
1.0below
8
9
|