Fully Automatic Washing Machine
User's manual
This manual is for
HWM85-728
Please read this manual carefully
before using.
Retain it for future reference.
0030508582
Packing list
Names of the parts
Names of the parts
Name
Quantity
One piece
User's manual
Warranty card
Top lid component
Water inlet valve
Water absorption
cushion
One piece
Detergent box
Control panel seat
Outer tub cover
Lint filter
Water inlet hose
Back control
board
The end connecting to
the washing machine
One piece
Jointer connecting
the water inlet hose
to the water faucet
Balance ring
Inner tub
Power cord
Filter cover
Pulsator
Control panel film
The end connecting to
the water inlet hose jointer
Handle
Drain hose
Hook
Blenching filler
Cabinet
Base
One piece
Put into the innner tub
Bottom plate
Screw cover
Adjustable foot
seam
Adjustable leg
Back cover
Meaning and description of the symbols
Tapping screw
One piece
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
One set
Fully automatic washing machine
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in
damage of the machine or influence the personal safety of
the users.
Forbidden sign
1
Trouble-shooting Answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department
or after-sale service department of our company. Do not repair it by yourself.
The washing machine must be positioned
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine. Do not plug
Phenomena
The reason
How to settle
The digitron displays E0.
The top lid is opened during reserve procedure.
Close the top lid.
or pull the power plug with wet hand.
Put down the drain hose. Open and close the
top lid once.
Clean the foreign material. Open and close the
top lid once.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
Close the top lid.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or the after-sale service department.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Are the laundries put slantingly?
Is the machine slanting?
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the start/Pause button once.
Push the Start/Pause button once.
The water filling does not work, or is
slow. After about 30 minutes later,
the digital displays E4.
Do not use water hotter than 50
.
In case the washing machine is installed on ground
with carpet, do not block the ventilation hole with
carpet.
Please contact the after-sales
service department.
The digitron displays E6.
The water level sensor is bad.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Not wash
The ventilation holes
at the bottom
The machine does
not act
Carpet
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Not spin
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
The water tap leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
The cloth sensor is checking the cloth, it will add water after 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
The pulsator pauses during water inlet
in wash and rinse.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
2
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Do not put hand into the rotating tub. It is dangerous
Do not decompose, repair or alter the machine by
yourself.
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
The lint filter must be used during washing.
Clean the detergent box and set it on
It must be cleaned in time after each using.
the control panel seat.
Lint filter:
1.The method of dismantle: Push it up aslant and gently.
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
2.The method of install : install it upwards and aslant
and push it in .
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
trol
Pe
Benzene
6.Make sure the lint filter well installed, or it can
influence your use.
Up
The back cover of lint filter
Up
Install
Dismantle
Dismantle
Install
Dismantle
Install
Down
The front cover of lint filter
Figure 2
The handicapped or children without care shall not use
the machine.
Down
Keep the machine away from direct sunlight and
heat source like the heater.
Figure 1
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
Benzene
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Install
Dismantle
damaged, please contact the customer
care agent of our company.
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
To change the direction of drain pipe, please contact the customer care agent of our company.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Attention
.
Even there's no water in the tub, a certain period is
required before spin starting.
Do not use the soak program for the woolen textiles.
Separate the laundries that are not colorfast from
other laundries in washing.
Install the bottom plate
After opening the package, please lean the
washing machine gently down on soft items
(like towel cloth,blanket, etc.). Install the bottom
plate to the bottom of the machine with one
screw by a cross screwdriver, then lift the machine
up gently. See to the figure:
I
Front
I enlarge
The pulsator will not rotate unless the water is
filled to"18L"water level.
Carpet
The soak procedure can work in cooperation with automatic programs like standard,normal, jeans, and fiber .
There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,soak and can not
make setting in other cases.
Back
The two claws of bottom plate should
insert the two strip holes ,and insure
3 Push the "PROCESS" button
You can choose one or more process among soak, wash, rinse, spin.
The button is invaid if you choose QUICK or TUB DRY program.
Adjust the Installation position
You can not choose soak process if you choose WOOL
program.
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground
will result in unstable running or stoppage of the machine. Please adjust it with following methods:
WATER
LEVEL
4 Push the " WATER LEVEL"button, select suitable water level
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
After switching on the power and the "standard"or" normal"programs set,washing machine will execute fuzzy
program automatically to detect the cloth.After defection, it can set the water level automatically. To select other
water level, first push the "start/pause" button, then push the "water level" button to
set the water level.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
the adjustable nut
Fasten
Loosen
2 . After adjustment, fasten the nut.
the adjustable feet
5 Push the "SELF-PROGRAM"button and "+ " " -"button
High
Low
to select suitable program
Set up timeOf soaking, washing, dehydration and times of rinse you can also set up an
appointment; set that means chosen the appointment booking functions, after start,
the light of process you choose will be off,a digital displays the remaining appointment
time (hours). Appointment process, holding down the "self-programming"button to display
the status of an appointment thatshows the procedureof your choice, water, process and
the remaining time (minutes). Run theprogram to changeor cancel an appointment,
need to cutoff the powersupply, re-select.In the light of article 11 can be"self-programming"
button and select button "+""-".
6 Push the "START/PAUSE" button
As the top lid opened, the washer will automatically given alarm and stop running,
exclusively during draining
7 Finish washing
After the laundry process, washing machines beep alarm, and then automatically power off
How to change the direction of the drain hose
6 "START/PAUSE" button
WATER
LEVEL
After the power is switched on, press it to start the machine
During working, push it to pause.
During pause, push this button to restart and go on working.
1.Loosen the screws of back cover, dismantle the back cover, then take off the drain hose
(As indicated figure 1)
Figure 1
REMAIN(MINUTES) indicator digitron
During sensing, it displays --
Drain hose
frame
RESERVE(HOURS)
2.Take off the drain hose from base, nip flat the drain hose mouth, dismantle the hang hook, take the
drain hose into cabinet from the left of base As indicated figure 2)
During delay procedure, it displays the remained delay time (in hours).
During operation of programs, it displays the remaining time (in minutes).
In case of abnormal phenomenon, it displays the abnormal symbols
Figure 2
nip flat the drain hose
mouth, dismantle the
hang hook
Steps of using the operation buttons and description of each step.
3.Extend the drain hose from the right side of base, fix the drain hose onto the base with the drain
hose frame, and screw down the screws, put the hang hole onto the drain hose ,then hang up the
drain hose.(As indicated in Figure 3)
POWER
ON/OFF
1.Push the "POWER ON/OFF " button to switch on the power
Figure 3
It has the special power resume function. In the case of power failure or the power plug is loose
during running , the machine can save the running program, and resume the program after the
power supply is recovered. You do not need to set the program again.
4.Install the back cover as primary state.
2.Push the "PROGRAM" button to select the suitable
automatic program
Remarks: in order to make sure of the correct of installation, it is suggested to change the
direction of the drain hose with our company serviceman .
Usage the drain hose
After switching on the power, the machine will set STANDARD program automatically. To select other
automatic program, push the "PROGRAM" button till the relative indicator is light . Refer to the
"PROGRAM "button on Page 10 for the selection. For instance: select "QUICK" program for laundries
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
with small quantity and light soil.
Page 10
In selecting the standard program, the machine will execute fuzzy program to select water level
and wash time according to the cloth and weight of the laundries. The full process is controlled
automatically.
2.Do not step on or press the drain hose.
Attention
Even there's no water in the tub, the spinning will start
after a certain period.
Wash and spin after putting the damageable clothes
into tuck net, to avoid scathe.
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
5.If the extra hose is too long, cut it either at A or at B.
Wash the laundries that are prone to lose colors separately
from other laundries.
When washing start or opening cover intermitting, the washing machine will begin
to work after a period time, this is normal phenomenon.
Only select rinse program,If there's water inside the tub, the machine will spin before
rinsing ,If there's no water the machine will rinse directly.
5
12
Install the water inlet hose
Confirm the water faucet
3 "PROCESS"button
You can choose one or more process among soak, wash, rinse, spin.
The button is invaid if you choose QUICK or TUB DRY program.
PROCESS
Water faucet,suitable
Water faucet,not suitable
You can not choose soak process if you choose WOOL
program.
Outlet end surface
4 "SELF-PROGRAM"button and "+ " " -"button
>10mm
Press the "Self-Program" button, the machine goes into the
self-program state when the associated indicated light
flickers. About 3 seconds later, you can change the program
by pressing "+" or " " button, to adjust reserved time (hour),
soak time (minute), washing time (minute), spinning time
(minute) or rinsing times (number of times) . When the time or
number of times is 0, it means you cancel all the functions the
flicker lights associated with.
When choosing the "quick" program, you can add or reduce
the reserved time. Choosing the "wool" program, you can add
or reduce the reserved time but cannot change the washing,
spinning time and rinsing times, it means the washing time,
spinning time and rinsing times are defaulted time, times or
zero. When choosing the "Tub dry" program, the "Self-
Program" and "+" "-" button are invalid.
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
SELF-PROGRAM
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
water inlet hose jointer
Screw
When choosing the "memory" program, after using the self-
program, the washing machine will remember the programs
you set this time when you use it next time.
Slider
Sign plate
Screw knife
Bushing
Lock level
water inlet hose
Figure 1
Figure 2
Figure 3
5 "WATER LEVEL"button
During standard programs, the washing machine can detect the laundries automatically.After
detection, it will set the water level to suitable valve automatically among the water level
"LOW","MEDIUM" ,"HIGH"and "MAXIMUM".
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
.
You can also set water level by yourself.After the machine is started, it will not set water level
automatically. You shall push the"START/PAUSE" button to make new setting.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
If there's water inside the tub, the machine can not detect the laundries and will display water
level "MEDIUM" .If wet aundries are put in, it may display water level "MAXIMUM" .
WATER
LEVEL
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
If "QUICK" program is selected, it will display water level "LOW". The water level can not
be adjusted.
During operation of wash , rinse and soak program, you can push down the water level
button to add water. When you release the button, or it reaches the overflow water level, the
machine will stop adding water.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
The water level decided may be different from actual value because of the different moisture
level of the laundries.
Figure 6
Figure 4
Figure 5
4 Use the operation buttons
Connection between the water inlet hose and the washer
RESERVE(HOURS)
1.Do not take off the water absorption cushion. Please check if the
66L
70L
62L
52L
40L
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
STANDARD
57L
46L
34L
MEMORY
SOAK
WASH
RINSE
please contact our after-sale department immediately.
POWER
ON/OFF
COTTON
WOOL
HEAVY
CHILD
QUICK
R
E
S
E
R
V
E
R
I
N
S
E
S
O
A
K
W
A
S
S
P
I
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
26L
18L
H
N
START
PAUSE
TUB DRY
SPIN
(M
(M)
(H)
(T)
(M)
jointer of the
water inlet valve
water absorption
cushion.
WATER
LEVEL
SELF-PROGRAM
PROGRAM
PROCESS
Connection between the jointer of the water inlet hose and the water inlet hose
the jointer of the
water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
Slider
Locking level
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Mode and meaning of the indicators
The light is off
Flashing: indicate the running program or indicate the water level
Check the connection between the jointer of the water inlet hose
and the water faucet
On: indicate the program about to run, or indicate the selected mode or indicate the water level
1 "POWER ON/OFF"button
Push the "POWER ON/OFF"button to switch on the power.
1.Swing the hose gently to confirm if it is fastened stable.
POWER
ON/OFF
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
Under power-on mode, push it to switch off the power.
Push the "POWER ON/OFF" button to switch on the power. If the "START/PAUSE"button is not pushed, the
machine will switch off the power automatically after 5 minutes.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
2 "PROGRAM"button
Applicable situation
Program
STANDARD
Washing the normal laundries
HEAVY Washing the bigger and heavier lanudries
GENTLE
Washing the woolen textiles or underwear
Quick waching of the light dirt laundries
Dismantle the water inlet hose
QUICK
PROGRAM
BLANKET
Washing the blanket
1. Close the water faucet.
COTTON Washing the cotton textiles
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Washing the woollen textiles
WOOL
Locking level
Drying the inner tub and the outer tub, which can avoid growing mildew.(after washing
clothes,there is dampness between the inner tub and the outer tub, the wall of the inner tub
TUB DRY and out tub can breed mildew, where you can choose thetub dry program, Drying the inner
tub and the outer tub, keeping the inner tub and outer tub dry, which can avoid growing mildew.
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
Slider
1 Preparation before washing
2.Put in the laundries
The capacity of washing and spinning of he
Preparation before washing
1.Connect the water inlet hose
machine refer to the largest weight of the standard
laundries under dry condition that can be washed or
spinned in one time.One time washing quantity
shall be lower than the rated capacity.
The thickness, size, type of the cloth will influence
the actual washing capacity. It is suitable for one
time washing to put in reasonable amount of laundries
and the laundries can be turned round in washing.
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose
Do not select high water level for laundries less than
1.0kg ,so as to avoid splashing of water.
3. Usage of the detergent
How to use the softener
The usage and dose of the softener as per the specifications
of softener.
Before washing put the softener into the detergent box directly
as indicated in the left figure The softener will be put into the
washer when the last rinsing.
Control panel seat
4.slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally
Liquid whitener inlet
Access for detergent
After that,please close the detergent box.Refer to the following
list for the usage of the detergent:selection of the water level,
water quantity and dosage of detergent.
Pay attention to followings before washing the laundries
After the softener is put in, please don't place for a long time
otherwise softener may solidify and cause flowing not smooth.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Fasten the buttons
and zippers.
Detergent box
How to use the washing powder
Access for softener
Directly dissolved in the machine (not applicable for
fuzzy program )
1.Fill small quantity of water.
2.Add the powder. Run for 30 seconds to dissolve it
completely.
How to use the whitener
laundries.
Fill water to decided level .Dilute
the whitener with container. Pour it
slowly into the washing tub.
Avoid using whitener on laundries
with colour or pattern as they are
prone to lose colour.
3.Put in the laundry. Select suitable water level.
The instant dissolving of the washing powder:
1.Prepare warm water of 30 and a container.
2.Add the powder while stirring to fully dissolve it. In
selecting the quick program, it is suggested to adopt
liquid detergent instead of washing powder to
guarantee the washing effect.
Put in the proper quantities detergent according to the
water level and the laundries quantities.
It is suggested not to use high sudsing detergent.
Washing powder with poor quality or long time storage
maybe caked. Please pay attention to cleaning the
detergent box in time.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g.For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for the
usage and quantity of the whitener.
For powder whitener, please
dissolve it before using.
|