Automatic Drum
Washing Machine
ꢀꢀ
HA1000TE HA800TE HA600TE
Table of Contents
Before using
Names of Parts---------------------------------inside front cover
Matters Needing Attention-------------------------------------1-3
Installation---------------------------------------------------------4-5
Control Panel--------------------------------------------------------6
Operational Functions-----------------------------------------6-7
During using
Program Selection-------------------------------------------------8
Preparation----------------------------------------------------------9
Washing Methods--------------------------------------------10-11
Other Function----------------------------------------------------12
Maintenance
Maintenance ------------------------------------------------------13
Trouble Shooting-------------------------------------------------14
Wiring Circuit------------------------------------------------------15
TechnicalSpecification------------------------------------------16
Matters Needing Attention
ƽ
Safety
2. Hold the plug and not the electric cable
when unplugging the washing machine.
1. A separate earthed socket is required
for the power supply. After installation of
the washing machine,the power plug
should be accessible during the normal
wash.
3. Fuses in the power circuit should be rated
for 15A. Refer to a washing machine techni-
cian or a Haier designated service point for
power cable replacement.
4. For your safety, dry hands before touch-
ing the washing machine and wear appropri-
ate footwear .
5. Do not use flammable detergent or dry
cleaning agent; do not use flammable
spray in close vicinity to the washing
machine; do not remove or insert the plug
in the presence of flammable gas.
6. The door of the washing machine will be-
come hot during the water heating process.
Avoid contact with the door during the heat-
ing process. For safety, keep children away
from the washing machine.
7. Do not allow children play with the packing materials after unpacking.
1
Matters Needing Attention
ƽ
Use
2
Matters Needing Attention
4. Do not wash foam rubber or similar sponge
materials.
3. Never place heavy objects ,a heating
applianceor a water container on the top panel
of the washing machine.
5. Before washing, do up zippers, buttons ,
laces and repair damaged areas,under-
wear or small articals should be placed
in the laundry bag or a pillowslip.
6. Do not open the detergent box during
the wash cycle.
Do not wash clothes containing wire
frames.
8. After washing, turn off the tap to prevent
leakage; unplug the washing machine
and wipe clean the lower part of the port
hole.
7. The door is fitted with a self-lock device and
will not open until 2~3 minutes after the wash-
ing machine stops. Do not force the door
open. Do not open the door when water level
reaches the port hole.
9. Keep the door slightly open when the washing machine is not being used. Never cover the
machine with a plastic sheet.
3
Installation
As shown in figure1 remove all the packing materials
ƽ
(including the foam base).
Upon opening of the package, water drops may be seen on
the plastic bag and the porthole. This in normal phenomenon
resultingfrom water test in the factory.
Fig 1
ƽ
Check attachments and materials.
Name
Operational
manual
Quality
Water
hose
Drainage
holder
Plastic
plugs
Qty
certificate
Model
HA1000TE
HA800TE
HA600TE
1
1
1
1
3
Remove the packing screws as shown in figure 2.
ƽ
The packing bolts protect the appliance from shock during trans-
portation The steps below should be followed before using the
appliance,
1. Remove the rear panel of the washing machine;
2. Remove the three packing bolts from the rear panel of the wash-
ing machine,the rubber hose and then the shock absorption chan-
nel steel;
3. Reinstall the back plate;
4. Fill the holes left by the packing bolts with plastic plugs.
(Attention: the packing bolts and rubber hose should be kept in a
safe place for later use)
Fig 2
Adjusting the position of the washing machine .There are ad-
ƽ
justable feet under the bottom of the washing machine. Before use,
the washing machine should be adjusted, as shown in figure 3, so
that it is level.
Fig 3
4
Installation
Connection of water inlet hose and washing machine
.
Water drainage hose
The height of the terminal of the water drainage
hose should be between 80cm-100cm, the water
drainage hose must be securely placed on the clip
on the back of the washing machine.
Use the water drainage support supplied as an
accessory for proper installation of the water drain-
age hose .fix the water drainage hose support with
waterproof sring.Do not use an excessively long wa-
ter drainage hose and contract the authorized tech-
nician if the water drainage hose needs to be
extended.the water drainage hose should not be ex-
tended more than250cm.(longer extension will result
in concurrent water inflow and outflow).The diam-
eter of the extension hose should be the same as
the original hose.
caution:water drainage hose must not be immersed
in water.the original and extension hoses should be
tightly connected .
Connection of power supply
Check the following items before connection to the power supply.
The socket conforms to the maximun power load(The maximum current load of the socket and
power supply cable should not be less than 15A).
Power supply voltage conforms to the required value.
The power supply socket and the plug of the washing machine compatible,if they are compat-
ible ,Refer to a washing machine technician or a Haier designated service point for power cable
replacement.The washing machine should be connected to an earth before use.
Supplementary earth cable should not be necessary if the socket is connected to the earth.
Supplementary earth cable should be installed on the upper back of the washing machine
andconnected to an earth if the power supply socket has no earth connection.
5
Control Panel
0
15
1
14
2
13
3
90
30
50
4
12
80
40
5
11
70
6
10
60
7
9
8
H
0
15
1
14
2
13
12
11
3
Turn the knob at "0", then turn off the power and
4
5
turn the program knob for setting desired wash program.
6
10
7
9
The program knob will not rotate with the programmed washing
process.
8
90
30
50
80
40
70
60
6
Operational Functions
ꢀ
Soak Button
For the synthetics cycle and the wool cycle, push the
button down, the anticrease funtion will be skiped and
automatically enter into the next step;Release the
button, the anti-crease funtion willwork again.
Economic Wash button
It reduces water and power consumption when
rinsing if the machine does not have a fullload.
Note: Select this function when "Cotton" "Synthetics", "Wool" or "Silk"
(programs 1-12) is selected.
7
Program Selection
HA1000TE/HA800TE/HA600TE
Program Setting
1 Intense
Laundry
Temperature
-30-40-50-60
*
Very heavy soil
-70-80-90
-30-40-50-60
Heavy soil
2
Prewash
*
-30-40-50-60
3
4
5
6
7
8
Normal
Middle
Soiled cotton
*
Non-fade and medium
soiled cotton
Fading and medium
soiled cotton
-30-40
*
Delicate
Normal
Middle
*
Non-fade heavily
-30-40-50-60
soiled chemical fiber
Non-fade and medium
soiled chemical fiber
Fading and medium
soiled chemical fiber
*
-30-40
*
Delicate
*
Non-fade heavily soiled
woolen fabrics
Fading and medium
soiled woolen fabrics
Non-fade heavily soiled
silk fabrics
9
-30-40
Normal
*
10 Delicate
11 Normal
12 Delicate
*
-30
*
Fading and medium
soiled silk fabrics
*
13
14
15
Quick
Rinse
Spin
-30
Medium-soiled lanudry
*
*
*
Turn the program knob at "0" position and turn off the power. The wash
program ends and the washing machine stops operation.
0
End
NOTE: " " means softener liquid detergent canbe added when necessary.
" " means detergent can be added when necessary.
" " means no detergent can be added.
8
Preparation
2. Water supply
1. Power supply
Plug in the power supply
220V~240V/50Hz.
Turn on the tap ensure that the water is clear.
Caution: Before staring the washing machine turn on the
water faucrt to ensure that the water faucet and the water
inlet hose are connected correctly and do not leak.
3. Laundry treament
4. Detergent selection
Only special low foam detergent
should be used in automatic
drum washing machine, form
blended or wool fabrics special
detergent should be used. dry
cleaning solvent should not be
used such as trichhloroethylene
or alike (caution :load the re-
quired amount of detergent only).
sort out clothes according to type and extent of dirt.
ƽ
There are three types of clothes: cotton, synthetical and
woolen (silk) fabrics.
separate white clothes from colored. If whites and
ƽ
coloreds are combined for one load, make sure the
coloreds are colorfast.
-Remove all objects from pockets that may cause dam-
age to the machine, such as keys and coins.
-Clothing with frayed edges or yarns should be put in a
wash bag or special bag before washing.
-Repaire damaged clothing,lose buttons or damaged zips
and hooks before washing.
-Bed sheets and table ware should be loosely loaded and
not folded.
This washing machine is for household use and de-
ƽ
signed for mechanically washable clothes. When washing,
separate unwashable clothes with reference to clothes
labels.
5.Wash Load
Woolen fabrics
1kg
Blending fabrics
2.5kg
Type
Delicate fabrics
Non-fade cottons
Max load
5kg
2kg
9
Washing Methods
1. Laundry loading
Reference loading
Evenly load the laundry in the
Overalls
(cotton 950g)
ƽ
ƽ
Jeans (800g)
washing machine and then tightly
close the door of the washing
machine
ƽ
Pajamas (200g)
ƽ
Blended
Note: 1) When first using the
washing machine, let it run un-
loaded for one program to pre-
vent the laundry from being
tainted by oil or dirty water from
the washing machine. 2) Do not
overload the washing machine.
fabric clothes
(800g)
ƽ
Shirts
(300g)
shirt
ƽ
ƽ
Underwear
(cotton
300g)
(blended fabrics 70g)
ƽ
Socks
(blended fabrics 50g)
ƽJackets
(cotton 800g)
ƽSingle bed
sheets
(cotton 800g)
ƽ
Woolen blankets
(3000g)
2. Use of detergent
Pull out the detergent drawer, put required detergent, soften-
ing agent and bleaching agent into the corresponding boxes.
Push back the drawer gently.
Caution: 1) Do not add liquid detergent into box 1 and 2
2) For pre-washing program, detergent should
be added to both box 1 and 2; for other
programs, do not add detergent to box 1
3) Do not overuse softening agent as this may
damage artificial fabrics.
3. Washing program setting
Set the wash program correctly in accordance with the laundry load. The methods for
setting wash programs are indicated on the handle of the distributor on the washing
machine. Turn the program knob to the desired program.
Caution: If you want to choose another program, first turn the program knob at "0", then
turn off the power and turn the program knob for setting desired program.
10
Washing Methods
4. Washing temperature Setting
Set the washing temperature as required, otherwise, set at position * when heating is not
needed.
5. Selecting the function button
Select function buttons as required (refer to the directions printed on the control panel) ,
otherwise keep all the button released.
6. Washing
Press the power button and the washing machine will automatically commence the pro-
grammed washing process.
Caution: The program knob will not rotate with the programmed washing process.
7. End
Wait 2-3 minutes after the washing process is finished , press the power button again to cut
off the power supply. Open the door to take out the laundry. Turn off the tap and unplug the
washing machine.
Caution: When the washing program finishes, the door lock light will glitter before the door can
be opened.
Additional information
Energy and water saving during wash process
1. Collect clothes for one full wash load.
2. Do not overload the washing machine.
3. Prewash heavily soiled clothes.
4. Reduce the amount of detergent or choose fast or minimal washing programs for lightly
soiled clothes dirty.
5. Choose a proper washing temperature. Only exceed 60 OC for heavily soiled clothes.
6. Do not use more detergent than required.
7. Softening agent makes clothes feel softer and easier to iron.
11
Other Functions
1. Power-off memory funtion:
This machine has a power-off menmory funtion. In case of abrupt power failure
or the power must be cut off during a program cycle, the present settings will be
saved, and operation will resume when the power is switched on again.
2. Trouble messages: judge the malfunctions from door lock light
Error 1: The door lock light does not illuminate.
Cause: Door is not properly shut.
Correction: Shut the door properly.
Error 2: The door lock light glitters 2 times and stops 4 seconds repeatedly.
Cause: Drainage error, water not emptied within 4 minutes.
Correction: Clean the filter and check the drain hose for blockage. If error still
exists, please contact the maintenance personnel.
Error 3: The door lock light glitters 3 times and stops 4 seconds repeatedly.
Cause: Temperature sensor not properly connected or damaged.
Correction: Contact the maintenance personnel.
Error 4: The door lock light glitters 4 times and stops 4 seconds repeatedly.
Cause: Heating coil damage or overload of laundry that leads to a failure to
reach the set temperature within the specified time (This message is display
at the end of a program).
Correction: Reduce load and then start washing again or contact the
maintenance personnel.
Error 5: The door lock light glitters 5 times and stops 4 seconds repeatedly.
Cause: Water level not met in 8 minutes.
Correction: Make sure that tap is turned on, and water pressure is normal.
If problem still exists, please contact the maintenance personnel.
Error 6: The door lock light glitters 6 times and stops 4 seconds repeatedly.
Cause: Timing control silicon damage.
Correction: Contact the maintenance personnel.
Error 7: The door lock light glitters 7 times and stops 4 seconds repeatedly.
Cause: Motor overheat protection or damage.
Correction: Contact the maintenance personnel.
Error 8: The door lock light glitters 8 times and stops 4 seconds repeatedly.
Cause: Water exceeds protective level.
Correction: Contact the maintenance personnel.
12
Maintenance
2. Unplug the machine during cleaning and
maintenance. Use a soft cloth dampened
with soapy liquid to clean the machine case
and rubber components. Do not use corro-
sive or abrasive chemicals or solvents.
1. Turn of the water and electricity supply af-
ter every wash. Open the door to prevent the
formation of moisture and odors. If the wash-
ing machine is left idle for a long period, drain
any remaining water in the machine and re-
place the drainage hose.
4. To prevent blockages to the water
supply or the ingress of contaminants,
clean the water inlet and inlet water
filter regularly.
4.
5. If the machine is to be moved a distance location,
replace the vibration mounting locks which were re-
moved during installation as shown below.
6. If the washing machine is left
idle for a long period turn off the
water and electricity supply and
open the door slightly to prevent
the formation of moisture and
odors.
Replace the rubber Insert the bolts.
plugs.
Remove the back
cover.
Replace the back
cover.
Tighten the bolts with a
spanner.
13
Trouble shooting
The following circumstances do not constitute problems. Do not contact the
maintenance service until the problem has been confirmed.
Problem
Possible Cause
ƽ
ƽ
ƽ
ƽ
Poor connection to power supply
Power failure
Door is not properly closed
Machine has not been switched on
The washing machine fails to
operate
ƽ
ƽ
ƽ
ƽ
ƽ
ƽ
Water is not turned on
Water pressure is less than 0.03MPa
The inlet hose is kinked
Water supply failure
The program knob is not properly set
The door is not properly closed
Washing machine does not fill
with water
The water supply and
drainage do not stop
ƽ
Check that the height of the water hose is below
80cm
ƽ
ƽ
Drainage hose is blocked
Drainage hose end is below 100cm above the
floor level
Drainage failure
ƽ
ƽ
Some packing fixing bolts removed
Washing machine on a uneven surface
Strong vibration during spin
Operation stops before comple-
tion of the wash cycle
ƽ
Water or electricity failure
ƽ
The detergent is not a low foam type
Excessive detergent has been used
Excessive foam in the drum
14
Technical Specification
Model
Item
HA1000TE
HA800TE
HA600TE
220V~240V/50Hz 220V~240V/50Hz 220V~240V/50Hz
Power supply
15
15
15
Maximum working current (A)
0.03
P
1
0.03
P
1
0.03
P
1
Water pressure
Washing power
(MPa)
(W)
230
230
380
5
230
Spinning power
(W)
400
5
340
5
Max. washing load
Spinning speed
(kg)
(r/min)
1000
800
600
Washing program
Maximum power
15
15
15
(W)
2000
2000
2000
Size
(mm)
850x520x595
65
850x520x595
65
850x520x595
65
Weight
Net
(kg)
Wiring Circuit
Motor
M8
M7
R
T
S
M1
M2
M3
M5
CN1-2
CN2-1
CN1-3
CN1-1 CN3-3
CN3-1
MR
CN2-2
CN6-4
CN6-3
MRN
NTC
MRL
MRC
CON3
PCB
SW
N
G
L
CON2
CON1
CN2-3
CN2-4
EVF
FA
EVP
CN2-6
CON3
CN3-3
CN3-4
CN2-5
EVC
12
13
14
PS
R
11
P
PCB-Printed Circuit Board
MR-Door Lock
PS-Drain Pump
EVP,EVF-Cold water Valve
FA-Interference Suppresser
SW-Power Switch
Motor-Motor
R-Heating Element
P-Pressure Switch
EVS-Hot Water Valve
NTC-Temperature Sensor
Motor-Motor
16
|