Fuzzy Computerized Automatic
Washing Machine
User's manual
This manual is for
HWM-6.5/S
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Top lidA
Water absorption cushion
Top lid B
Detergent box
Water valve
Cabinet handle
Drain hose
Lint filter(Installed by user)
Lint filterA(Installed by user)
Control panel
Filter cover
Inner tub
Power line
Pulsator
Control panel film
Cabinet
Adjustable foot
back cover
fixed foot (3)
base frame
Meaning and description of the symbols
Contents marked with that symbol are related to the safety
Warning sign
of the product and the personal safety of the users. Please
operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety
of the user.
Contents marked with that symbol are actions forbidden to
perform. Performing of those actions may result in damage
of the machine or injure the personal safety of the user.
Forbidden sign
1
Safety precautions
The power cord plug should be convenient
Please insert the power cord into special
receptacle with rated voltage. Be sure to
use single-phasethree pins receptacle.
Ensure the earthing prong of the power
receptacle is earth edreliably. Use leakage
protector if possible.
to be pluged in or pluged out with hand
while the washing machine runs normally.
Be sure to pull the plug out and close the
water tap when the machine is idle, when
moving the machine, or when cleaning
the machine. Do not use wet hand to ins-
ert or pull out the power plug.
Do not damage the power cord, bend ,extend, twist, bind or alter it by force. Do not press or
nip it with weight. If the power cord or the power plug is bad, or the power plug becomes
flexible, to avoid risk it is required to have it replaced by the technicians of our special
shop or the after-sale service department. Keep the pin of the power plug clean, if the
power plug is polluted with dust, please wipe with dry cloth carefully.
Do not put the machine at damp place like
Do not use water hotter above 50 C .
the bathroom. Never wash it with water.
Not put wet laundries on the control panel.
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
The ventilation holes
at the bottom
soft items
Do not let the machine share one receptacle with other
electric appliances. If the power plug is damaged, or
the plugging into the receptacle is loose,
do not use the plug any more.
2
Safety precautions
Do not stretch hands into the working
Do not decompose, repair or alter the
machine by yourself.
machine. It is dangerous even if the
rotation is slow. Take special care of
the children. Do not let the children
climb the washing machine.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
trol
r
Pe
nne
Thi
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
3
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
Install the lint filter
Install the bottom plate
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of the
machine with the eight screws by a cross
screwdriver, then lift the machine up gently.
See to the figure:
Push lint filter downward to location for lint filter .
Install
Install
Front
Back
Soft items
Screw
Bottom plate
Adjust the installation position
The largest allowed slope of the
shank base of the machine is 2
.
The slanting or rough ground will
result in unstable running or
stoppage of the machine. Please
adjust it with following methods:
Adjust the adjustable foot:
1.To twist the adjustable foot, please
first lift up the side of the foot slightly,
loosen the adjustable nut, and twist
the foot.
adjustable nut
Fasten
adjustable foot
Loosen
High
Low
2.Fasten the nut after adjustment.
4
How to change the direction of the drain hose
3
protrude the drain hose from the hole
on the right side of the bottom, and fast
it onto the bottom with the rack and screws.
Set the bracket on the drain hose .There
is a hole on the cabinet to hang the drain
hose (as figure 3).
1
Dismount the back cover of the washing
machine.
Figure 3
drain hose rack
Figure 1
4
install the back cover as what it looks
before.
2
Take off the drain hose frame. Put down
the drain hose. Take off the drain hose rack.
As indicated in Figure 1 Pull the drain hose
into the cabinet from the left side of the bottom
(as figure 2).
Figure 2
Usage of the drain hose
The drainage shall be smooth with the drain hose.
1.put the drain hose up to suitable position. Do not
put it on ground
2.Do not step on or press the
drain hose.
Notes: the highest point of drain pipe should be higher
than the water level of washing tub for avoiding
to siphon phenomenon during drain.
The highest point
5
Install the water inlet hose
1. Attach the water inlet hoses to the water faucet. Using pliers, tighten
the coupling. ( As figure 1)
NOTE: Do not over tighten. Damage to the
valves can result.
2. Connect the other ends to the water inlet valve .
( As figure 2)
Figure 1
Jointer of the water inlet hose
Jointer of the
water inlet valve
Figure 2
Water absorption cushion
6
Check the connection between the water inlet
hose and the water tap
1.Swaying the hose gently to confirm if it is fastened
stable.
2.After installation, open the tap to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the water inlet hose and the water tap is firm,
so as to prevent dropping from improve Installation
position.
Take down the water inlet hose
1.After using,Close the water tap.
2. Pull off the water inlet hose from the water tap and washer
Preparation before washing
Preparation before washing
1. Connect the water inlet hose.
2. Confirm that the washing machine is
earthed reliably. Then insert the power
plug into the receptacle. Do not connect
the earth terminal to the gas pipe and tap
water pipe.
3. Hang up the drain hose.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Confirm
if
Clear the pocket. Fasten the The quantity of
When the pulsator
the laundries is running , the
shall not exceed buttons of the
the rated value. laundries may
The big laundries cause noise. For
there's special Take out the
requirement for coins , sand,
the laundries. hairpins etc.
buttons and
zippers.
like the jeans
shall be put in
loosely.
t h e s a k e o f
discretion, please
put the laundries
with buttons into
other laundries.
a. Please check if the laundries are applicable for washing.
b. Separate those not colorfast from other laundries.
c. For laundries not water absorbing, please put them into water with hands.
d. For laundries with much soil, please remove the soil first. You can add detergent on the
part with serious soil directly. It is much easier to remove the soil by that mean.
e. For laundries likely to get lint ball or with long fiber, please first turn the inside out before
putting them into the water.
f. Do not put the laundries polluted with chemicals directly into the washing machine.
G. For those small laundries ,laundries likely to be twisted or worn, and woolen laundries,
please put them into mesh bag before washing.
h. Do not select heating function for clothes that should avoid hot water or wear.
i . In order to prevent the heating band from being entangled, washing of seriously worn
or linty clothes should be prohibited.
8
Put in the laundries
The capacity ofwashing and spinningof the
machine refer tothe largest weightof the standard
laundries under drycondition that canbe washed
or spinned inone time. Onetime washing quantity
shall be lowerthan the ratedcapacity. The largest
capacity of thismachine is 5.0kg.
The thickness, size, type of thecloth will influence
the actual washingcapacity. Itis suitable forone
time washing toput in reasonableamount of
laundries and thelaundries can beturned round in
washing.
Do not selectHigh water levelfor laundries less
than 1.0kg, soas to avoidsplashing of water.
To wash thin laundrieslike the stocking, silk etc.,
please first putthem into washingmesh bag (which
can be purchasedseparately) before wash.
Usage of the detergent
How to use the washing
powder
Direct dissolved in the machine
1.Fill water to "Low" water level.
2.Add the power. Run for 30 seconds
to dissolve it completely.
Inlet box of the detergent
3.Put in thelaundries. Select
suitable water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 and a
container.
2.Add the powder while stirring to
fully dissolve it.
Put in the prorer quantities detergent
according to the water level and the
laundries quantities .
It is suggested not to use high
sudsing detergent.
Washing powder with poor quality or
long time storage maybe caked.
Please pay attention to cleaning the
detergent box intime
How touse the whitener
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on
laundries with color or pattern as
they are prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for
the usage and quantity of the
whitener.
For powder whitener, please
dissolve it before use.
9
Use the operation buttons
a. Description of the function of the buttons
"PROCEDURE"button
With it you can select one or
several processes of soak,
wash, rinse and spin.
STANDARD
SOAK
JEANS
WASH
RINSE
SPIN
GENTLE
QUICK WASH
WATER
LEVEL
SELECTION
PROGRAM
SELECTION
PROCEDURE
SELECTION
" WATER LEVEL"button
The user selects a suitable water level depending
on the load.
If "Quick" wash is selected, water level will
indicate "2". After water level reaches "2", it will
wash while water filling, and wash normally upon
the water level reaching "4".
AM " button
GR
"PRO
You can select from the following four programs.
Normal wash
Standard
Jeans
After washing for 1 min, pressing "Water level"
button will enable supplemental water filling, which
will stop automatically upon the water reaching
overflow level.
Large, thick or heavily
soiled laundry
Woolen textiles or underwear
Gentle
10 min quick wash for
load below 1 kg
Quick
Remarks: After pressing "POWER ON/OFF" to connect power supply, if the washing machine
lasts idle more than 10 min, it would automatically shut off the supply.
10
SURPLUS(MIN)
"START/PAUSE"button
To indicate -- during sensing.
To indicate remaining min. During
program running.
After the power is switched on, press it to
start the machine
During working, push it to pause working.
During pause, push this button to restart
and continue operation.
To indicate remaining reserved
time (hrs) during reservation period.
To indicate fault symbols for abnormal
"POWER ON/OFF"button
conditions (see page 16)
Page 16
Press "Power On/Off" button to
connect power supply.
After power is connected, pressing this
button will cut off the supply.
SURPLUS MIN
POWER
ON/OFF
START
PAUSE
RESERVATION
CALEFACTION
"RESERVATION/CALEFACTION" button
Press "RESERVATION/CALEFACTION"button to set scheduling or heating
Function. If heating function is selected, the scheduling function is unavailable.
During machine running, the display indicates the cycle remaining time in
minutes). Press "RESERVATION/CALEFACTION"button, the display will
Indicate the remaining scheduled time to cycle end (in hours), the decimal point
flashes to indicatethe scheduled progress.
Heating function can be selected if keep pressing "RESERVATION/
CALEFACTION"Button for more than 2 s. If the temperature indicator is
lighted, it means heating function is selected. If keep pressing
The"RESERVATION/CALEFACTION"button for more than 2 s, the
temperature indicator turns off, and the heating function is cancelled. The
initial temperature is about 30 , and you can select your
desired value in 3 s in a switching sequence 30
After the machine starts running, if selection or cancellation of
40
20
.
heating function isdesired, you shouldswitch off the power andreselect.
11
Operating procedure and explanations for the
b.
buttons
STANDARD
JEANS
SURPLUS MIN
SOAK
WASH
RINSE
SPIN
GENTLE
QUICK WASH
POWER
ON/OFF
WATER
LEVEL
SELECTION
START
PAUSE
PROGRAM
SELECTION
PROCEDURE
SELECTION
RESERVATION
CALEFACTION
1 Press the "POWER ON/OFF" button to switch on
the power supply
POWER
ON/OFF
After switching on, the washing machine heating function will be
automatically set inactive.
In order to select heating function, the
should be pressed for more than 2 s until the heating indicator is lighted, which means
the heating function is selected. The initial status is 30 , and 40 or 20 can be
selected if you press RESERVATION/CALEFACTION button again in 3s.
"RESERVATION/CALEFACTION"button
"
"
It has the special power resume function. In the case of power failure
or the power plug is loose during washing, the machine can save
the running program, and resume the program after the power
supply is recovered. You do not need to set the program again.
2 Press the button of" PROGRAM "to
select a suitable full-automatic program
PROCEDURE
SELECTION
After switching on, the "Standard" program will be thedefault. If other full-automatic program is
desired, you can press the button "PROGRAM/SELECTION" to getthe corresponding
indicator on. Refer to the"Button of 'PROGRAM/SELECTION '"
paragraph on page 10.
Example: Use the "Quick" program for slightly soiled articles.
Page 10
When "standard" programis selected, thewashing machine willperform full-automatically
controlled fuzzy programto set waterlevel, water flowand wash duration according to the
cloth nature andweight
12
3 Press the button of "PROCEDURE SELECTION"
to select suitable processes.
PROCEDURE
SELECTION
After the power is switched on, the washing machine will automatically
set a normal program comprising of processes of "Wash, Rinse and Spin" .
If other program is desired, press the button of "Process" to select one
or several process of soak, wash, rinse and spin. Refer to the
paragraph "Processes selecting".
Page 10
Attention
Even there's nowater in thetub, the
spinning will start after acertain period.
Do not use soak process for woolen laundries.
Wash the laundries that are prone to lose
color separately from other laundries.
The pulsator will not rotate unless the
water is filled to selected water level.
Selection method of the procedure programs
Times of pushing Selected procedure
the"select"button program
Contents(the lighted indicators
indicate the programs about to run)
Applicable procedure
When the commonlaundries
need washing, rinsingand
spinning.
Soak Wash Rinse Spin
Soak Wash Rinse Spin
Soak Wash Rinse Spin
Soak Wash Rinse Spin
0
1
2
3
4
5
Wash, rinse, spin
Wash(the washing
liquid remains in the
tub)
Repeat using thewashing
liquid
Wash,rinse(the
rinsing liquid remains
in the tub)
The laundry needn't spin to
avoid wrinkles
When the laundriesneed
rinsing and spinningafter
manual washing
Rinse,spin
When the laundriesneed only Soak Wash Rinse Spin
spinning after manual
washing (first drainthen spin)
Spin(spin after drain)
Soak,wash,rinse,spin
Soak Wash Rinse Spin
If the laundriesare very dirty,
or the sleeveand collar are
dirty, firstsoak then wash
If you push the "PROCEDURESELECTION" button for6 times, itwill resume the
original mode, andit will circulatelike that.
If you select the"QUICK WASH" program, youhave to setthe full procedureof
wash, rinse andspin. The procedure can notbe selected.
13
4 Press the "WATER LEVEL" button to select
suitable water level
WATER
LEVEL
SELECTION
After switching on the power, press the button "WATER LEVEL" to select a water level according
to the load. Please refer to the button " Water level" on page 10.
Page 10
5 Push the " RESERVATION/CALEFACTION"
RESERVATION
button to select suitable reserve programCALEFACTION
After switching on, the washing machinereserved wash programwill be automaticallyset
inactive. If youdesire a washcycle to endat a reservedtime, you canpress the
"RESERVATION/CALEFACTION”button to set a reserved wash program.
Refer to The button of "RESERVATION/CALEFACTION" on page 11.
Page 11
Confirm the reserveprogram
When "Reservation" becomes active, the nixie tube displays the time
to the end of the reserved wash cycle, and the indicator turns on.
To change the running program or cancel the reservation,
the washing will finish
about 18 hours later
you should cut off the supplyand reselect.
Confirm the heating function
Keep pressing the"RESERVATION/CALEFACTION" button for more than 2 s,
the heating indicator turns on (red).
Keep pressing the "RESERVATION/CALEFACTION"button for morethan 2 sagain, the
heating indicator turnsoff and heatingfunction is cancelled.
After the machinestarts running, ifselection or cancellationof heating function
is desired, youshould switch offthe power andreselect.
START
PAUSE
6 Press the "start/pause" button
Close the top lid
Except water filling (excluding heating function) and draining process,
if the top lid is opened, the machine will stop running and alarm.
Finish washing
The washing machine cuts off thepower supply automatically when wash cycle ends.
14
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Install
Dismantle
1. Pull upward to dismantle lint filter.
2. Push downward to install lint filter.
Dismantle
Install
Clean
3. Please clean lint filter after wash.
Dismantle & Install
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol,
alcohol etc.
The filter screen of the water inlet
valve is likely to be blocked by
foreign materials and influence
the water inlet. Please clean it
Alcohol
Petrol
ner
Thin
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after
each using.
3.Be sure to pull off the power plug before maintenance.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for
some time (about 1 hour), then close the top lid.
15
Trouble shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance
department or after-sale service department of our company. Do notrepair it by yourself.
Phenomena
Reason
How to settle
After the reservation is started,
it rings and the digital tube
displays "E0"
The top lid is not closed
Close the top lid
Is the drain hose blocked by
foreign material?
Clean the foreign material. Open
and close the top lid once.
The draining does not work,
or the speed of draining is
too slow. The digital tube
displays "E1" and it rings.
Is the drain hose frozen?
Clean the frozen material.
Some minutes later the machine will
continue to work
After long running of pump in the hot
weather, power will be cut automatically
for safe.
It stops running except water
filling and draining. The digital
tube displays "E2" and it rings.
The top lid is not closed
Close the top lid
The safety switch acts. The
spinning cannot work (after
twice revising). The digital
tube displays "E3" and it rings.
Are the laundries put slantingly?
Is the machine slanting?
Re-order the laundries. Close the top lid.
Level the machine in right position.
Open and close the top lid once.
It does not do water inlet or
the speed is slow (the water
level is not reached after 15
minutes). The digital tube
displays "E4" and it rings.
Is the water faucet open or is
there water supply failure?
Open the water faucet. Open and close
the top lid once.
Is the water inlet valve is
blocked
Clean the water inlet valve. Open and
close the top lid once.
The machine does not act.
(The indicators are off.)
Is there power failure?
Is the power plug loose?
Is the machine slanting?
Use it when the power is on.
Insert the power plug tightly.
Level the machine properly.
Fasten the buttons and zipper
Is there metal material inside
the washing machine?
There's abnormal sound
inside the machine.
Are the laundries slanting in
spinning?
Re-order the laundries. Close the
top lid.
Fasten the jointer screw properly.
Is the jointer screw of the water
inlet hose is loose or twisted awry?
The water faucet leaks.
Common phenomena
Explanation
Phenomena
The spinning is intermittent when it starts.
Pause during washing.
Balance the laundries to avoid slanting.
supplemental water filled after fabric sensor has checked
fabric (about 48 seconds)
The program is setting the drain time. Some
time is needed before it starts spinning.
Select spin, but it doesn't work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
If heating function is selected before reaching the selected temperature in order
to let the water heating uniformity the Pulsator turns mildly. After arriving the
selected temperature it can works in gear.
The Pulsator turns mildly after inlet the water
but always feels immobilly.
Select the heating function the temperature indicator
is lighted sometimes twinkles sometimes not.
When the machine is in heating sate the temperature indicator twinkles.
Select the heating function if not in the sate the lighted does not twinkle.
It is the special power resume function. In the case of power failure
or the power plug is loose during washing the machine can save
the running program and resume the program after the power
supply is recovered. You do not need to set the program again.
When the power plug is inserted, the computer board
indicator is switched on, and the machine starts working
This is the normal phenomenon .The actual heating temperature is also
influenced by the atmosphere temperature the water temperature for
wash and the water hardness.
The actual heating temperature may have discrepancy
with the setting level.
16
Packing list
Name
Quantity
One piece
User's manual
Warranty card
Water inlet hose
One piece
The side of connection between the water inlet
hose and the washing machine
One piece
The side of connection between the jointer of
the water inlet hose and the water faucet
Lint filter
Two pieces
Two pieces
One piece
Lint filter A
Bottom plate
Tapping screws
Eigh piecest
One set
Fuzzy computerized automatic washing
machine
Specification
Water level/Water
quantity (about)
0.03MPa-0.78MPa
Water inlet pressure
Rated washing /
spinning capacity(kg)
5.0 /5.0 (weight of standard dry cloth)
6.5/6.5 (weight of standard dry cloth)
Max washing /
spinning capacity(kg)
17
|