Haier Flat Panel Television LED LCD TV User Manual

LED LCD TV  
OWNER' S MANUAL  
MODEL: LE32B50  
Please READ this manual carefully  
before operating your TV, and retain  
it for future reference  
 
SAFETY AND WARNINGS  
IMPORTANT SAFETY INSTRUCTION  
1) Read these instructions.  
CAUTION  
2) Keep these instructions.  
RISK OFELECTRIC SHOCK  
DO NOTOPEN!  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings, install  
in accordance with the instructions.  
CAUTION  
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO  
NOT REMOVE COVER (OR BACK).NO USER  
SERVICEABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED SERVICE PERSONNEL.  
8) Do not install near any heat sources such as  
radiations, heat registers, stoves, or other  
apparatus (including amplifiers) that produce  
heat.  
9) Do not defeat the safety purpose of the  
polarized plug. If the provided plug does not fit  
into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
The symbol indicates that dangerous  
voltages constituting a risk of electric shock  
are present within this unit.  
The symbol indicates that there are  
important operating and maintenance  
instructions in the literaturaccompanying this  
unit.  
10) Protected the power cord from being walked  
on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from  
the apparatus.  
WARNING:  
To reduce the risk of fire or electric shock, do  
not expose this apparatus to rain or moisture.  
11) Only use attachments/accessories specified  
by the manufacturer.  
WARNING:  
The batteries shall not be exposed to  
excessive heat such as sunshine, fire or the  
like.  
12) Unplug this apparatus during lighting  
storms or when unused for long periods of time.  
13) Refer all servicing to qualified service  
personnel. Servicing is required when the  
apparatus has been damaged in any way, such as  
power-supply cord or plug is damaged, liquid  
has been spilled or objects have fallen into the  
apparatus, the apparatus has been exposed to  
rain or moisture, does not operate normally, or  
has been dropped.  
This symbol indicates that this product  
incorporates double insulation between  
hazardous mains voltage and user accessible  
parts. When servicing use only  
14) Mains plug is used as the disconnect device,  
the disconnect device shall remain readily  
operable.  
identical replacement parts.  
15) The ventilation should not be impeded by  
covering the ventilation openings with items,  
such as newspapers, table-cloth, curtains, etc.  
16) No naked flame sources, such as lighted  
candles, should be placed on the apparatus.  
17) Attention should be drawn to the  
environmental aspects of battery disposal.  
This marking indicates that this product should  
not be disposed with other household wastes  
throughout the EU. To prevent possible harm to  
the environment or human health from  
18) The use of apparatus in moderate climate.  
19) The apparatus shall not be exposed to  
dripping or splashing and that no objects filled  
with liquids, such as vases, shall be placed on  
the apparatus.  
uncontrolled waste disposal, recycle it  
responsibly to promote the sustainable reuse of  
material resources. To return your used device,  
please use the return and collection systems or  
contact the retailer where the product was  
purchased. They can take this product for  
environmental safe recycling.  
-2-  
 
SAFETY AND WARNINGS  
High voltages are used in the operation of this television  
receiver. Do not remove the cabinet back from your set.  
Refer servicing to qualified service personnel.  
Never stand on, lean on, or suddenly push the television or  
its stand. You should pay special attention to children.  
Serious injury may result if it falls.  
To prevent fire or electrical shock hazard, do not expose  
the television receiver to rain or moisture.  
Do not place your television on an unstable cart, stand,  
shelf or table. Serious injury to an individual , and damage  
to the television, may result if it falls.  
Do not drop or push objects into the television cabinet  
slots or openings. Never spill any kind of liquid on the  
television receiver.  
When the television receiver is not used for an  
extended period of time, it is advisable to disconnect  
the AC power cord from the AC outlet.  
Do not block the ventilation holes in the back cover.  
Adequate ventilation is essential to prevent failure of  
electrical components.  
Avoid exposing the television receiver to direct sunlight  
and other sources of heat. Do not stand the television  
receiver directly on other products which give off heat,  
e.g. video cassette players and audio amplifiers. Do not  
place naked flame sources, such as lighted candles on  
the television.  
Dim:515*320mm(  
Do not trap the power supply cord under the television  
receiver.  
If the television is to be built into a compartment or similar  
enclosure, the minimum distances must be maintained. Heat  
build-up can reduce the service life of your television, and  
can also be dangerous.  
-3-  
 
INTRODUCTION  
Accessories  
Main features  
5
Used as Television, display terminal, PC display;  
High luminance, wide viewing angle;  
Can store 200 TV programs;  
HDMI interface;  
Infrared Remote Controller............1  
Battery(AAA)...............................2  
Users Manual...............................1  
Multi-Media player (USB);  
Main parameter  
Viewing Picture Size (Diagonal)  
Resolution  
Aspect Ratio  
32 inch  
1366x768  
16 : 9  
TV System  
PAL/BG PAL/I PAL/DK SECAM/BG SECAM/DK  
PAL/NTSC/SECAM  
Video Signal System  
Receiving Channel  
1-200  
Input Power Voltage  
Power consumption  
AC 100-240V 50/60Hz  
50W  
THD 7%2x8W  
Audio Output Power  
Signal Input/Output  
Analog RGB(VGA) x 1  
High-Definition Multimedia Interface (HDMI) x 2  
Composite Video Input x 1  
Composite Video output x1  
Audio Input x 2  
Headphone x 1  
YCb (Pb)Cr (PR) x 1  
USB x 1  
RF x 1  
Composite Video input >=350  
Horizontal definitionTV line)  
Y Cb(Pb ) Cr(Pr)  
>=400  
-4-  
 
INSTALLATION  
KEYBOARD  
Front panel  
1
2
3
4
5
SOURCE  
MENU  
CH+  
CH-  
VOL-  
VOL+  
STANDBY  
1
3
2
30 30  
USB  
MUTE  
PICTURE AUDIO ASPECT SLEEP  
1SOURCE:  
Display the input source menu.  
2MENU:  
Display main MENU.  
3CH+/CH-  
DISPLAY  
MENU  
RECALL  
INPUT  
OK  
CH.LIST  
VOL-  
EXIT  
CH+  
VOL+  
CH-  
PLAY/PAUSE STOP  
PREV  
NEXT  
In TV modepressCH+orCH-to change  
the channel up and down.  
In MENU mode, press CH+orCH-to select  
items.  
1: Remote control sensor.  
2: Indicator LED: BLUE  
RED  
4VOL+/VOL-  
Adjust sound level.  
POWER ON.  
STANDBY.  
In MENU mode, pressVOL+orVOL-to  
adjust the item that you selected.  
5. STANDBY  
3: Key board  
Press this button to turn the unit ON from  
STANDBY mode.  
Press it again to turn the set back to STANDBY.  
REAR AV Connections  
AV INPUT  
L
AV OUTPUT  
L
VIDEO  
R
VIDEO  
R
AC-INPUT  
100-240V~50/60Hz  
All the terminals are(from left to right):  
AC POWER SOCKET, AV INPUT, AV OUTPUT.  
Note: VIDEO and YPbPr share one audio channel.  
REAR AV Connections(SIDE)  
USB  
HDMI2  
HDMI1  
HEADPHONE  
PC AUDIO  
VGA  
RF  
Y
Pb  
Pr  
All the terminals are (from left to right):  
USB, HDMI2,HDMI1, YPbPr INPUT, HEADPHONE, PC AUDIO, VGA, RF.  
Note: When HDMI port get DVI signal, the audio signal receives from the PC  
Audio channel.  
-5-  
 
INSTALLATION  
ANTENNA  
Note:  
Aerial connections: IEC(female).  
Input impendance: 75 unbalanced.  
PC  
STEPS:  
Be sure both the TV and computer are  
set to Power off.  
1.Connect VGA and audio cable.  
2.Connect the power cord.  
3.Power on the TV, switch to PC mode.  
4.Power on the PC.  
This sequence is very important.  
USB  
HDMI2  
HDMI1  
HEADPHONE  
PC AUDIO  
VGA  
RF  
Y
Pb  
Pr  
-6-  
 
INSTALLATION  
AV INPUT  
L
AV OUTPUT  
L
VIDEO  
R
VIDEO  
R
AC-INPUT  
100-240V~50/60Hz  
PRESET MODE (PC)  
V.Freq.(Hz)  
H.Freq.(KHz)  
RESOLUTION  
1
2
3
800*600  
60  
37.88  
1024*768  
1360*768  
60  
60  
48.36  
47.7  
NOTE: PC V.Freq.(Hz) not more than 60Hz.  
PRESET MODE (HDMI)  
V.Freq.(Hz)  
H.Freq.(KHz)  
RESOLUTION  
1
2
3
4
5
800*600  
1024*768  
1360*768  
1280*768  
1920*1080  
60  
37.88  
60  
60  
60  
60  
48.36  
47.7  
47.3  
67.5  
-7-  
 
INSTALLATION  
AV EQUIPMENT  
This TV provides one group of AV ,one group of YPbPr for convenient connection to VCR, DVD  
or other video equipment. Please refer to the owner's manual of the equipment to be connected  
as well.  
You can use the input terminals on TV set rear as follows.  
USB  
HDMI2  
HDMI1  
HEADPHONE  
PC AUDIO  
VGA  
RF  
Y
Pb  
Pr  
G
B
R
VIDEO EQUIPMENT with YPbPr  
HDMI  
W
R
G
B
R
Y
R
W
R
B
G
Yellow (video)  
Red (audio R)  
White(audio L)  
Red(Pr or Cr)  
Blue(Pb or Cb)  
Green(Y)  
R
W
AV INPUT  
L
AV OUTPUT  
L
VIDEO  
R
VIDEO  
R
AC-INPUT  
100-240V~50/60Hz  
W
R
Y
W
R
Y
VIDEO EQUIPMENT  
VIDEO EQUIPMENT  
W
R
W
R
Y
TO VIDEO  
INPUTS  
TO VIDEO  
OUTPUTS  
TO AUDIO INPUTS  
TO AUDIO OUTPUTS  
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder,  
video game or stereo system, etc.....  
YPbPr can support these video formats:480i,576i,480p,576p,720p,1080i,1080P.  
Note:  
1.AV and YPbPr share one audio channel.  
2.When HDMI port get DVI signal, the "PC Audio" channel is changed to receive the  
audio for HDMI port.  
3.Sometimes it will not support in different device because the device supplys  
nonstandard signal.  
4.When current source is TV, AV OUT signal is TV; when current source is AV, AV OUT  
signal is AV; other sources have no AV OUT signal.  
-8-  
 
REMOTE CONTROLLER  
The remote control cannot be operated unless the batteries are properly loaded inserted.  
When using the remote control, aim it at the remote control sensor on the TV.  
Function introduction  
1
2
1.Press to turn on and off the TV.  
2.USB:Press to launch the USB multimedia mode  
3.Switches the TV sound on or off.  
4.Press repeatedly to cycle through the available  
picture modes.  
USB  
MUTE  
3
PICTURE AUDIO ASPECT SLEEP  
13  
14  
4
5
5.Press to cycle through the different sound mode  
settings  
6.Press to change a channel.  
6
7.Press to display the TV status information on the bottom.  
8.Press to open the on-screen menu  
9.Open the channel list in TV mode.  
15  
16  
RECALL  
INPUT  
7
8
DISPLAY  
MENU  
10.Press CH+ or CH- to go to the next or previous  
channel. Press VOL+ or VOL- to increase or  
decrease the volume.  
11. Play/Pause Stop  
Previous  
Next  
17  
18  
12.Be used in programme edit:  
Red: Delete  
OK  
Green: Rename  
Yellow: Move  
Blue: Skip  
CH.LIST  
VOL-  
EXIT  
CH+  
9
19  
VOL+  
CH-  
13.Press to display the sleep timer option.  
14.To change the picture aspect ratio: Auto,4:3,  
16:9,Zoom, Zoom2.  
15.Press to go to the last viewed channel.  
16.Show the input source menu.  
10  
11  
12  
PLAY/PAUSE STOP  
PREV  
NEXT  
17.Press to confirm selections in an on-screen menu  
or to open a submenu.  
18.To move within the menu.  
19.Exit On Screen Display.  
-9-  
 
TV OPERATION  
1. CHANNEL MENU  
The first item of the MENU is channel menu ( for  
TV source only).  
Delete  
Delete  
You can search channels and edit programs here.  
Press  
to choose the program.  
Press  
and press  
to move, press OK button to confirm,  
to adjust.  
Press red button, the program will delete.  
Rename  
Rename  
Move the cursor to the program, press  
green button to rename the program.  
Auto Tuning  
Sound System  
Manual Tuning  
Programme Edit  
Press  
move the cursor.  
to choose the character. Press  
to  
CHANNEL  
Software Update(USB)  
<
>
Press MENU button to exit edit, Press EXIT to exit  
the menu.  
Note: The TV programs name only can be 5 characters.  
Move  
Move  
Move the cursor to the program, press  
yellow button, it will show yellow cursor, Press  
to move the program.  
1).Auto tuning:  
Search all the TV channels automatically.  
Skip  
Skip  
2). Sound System  
You can change the sound system.  
Press  
to choose the program, press  
blue button to skip this program, The icon  
show on the right side of the program.  
will  
3). Manual tuning:  
You can search the TV channels and fine tune the  
channels, then storage the channels you selected.  
Choose the skipped program, press the blue button  
again, you can cancel the skip, Then the icon  
disappear.  
will  
Manual Tuning  
_
Storage To 2  
+
5). Software update(USB):  
Current CH 2  
Search  
Update the TV set' s software by USB.  
2. PICTURE MENU  
The second item of the MENU is PICTURE MENU.  
You can adjust picture effect here, such as contrast,  
brightness, etc.  
Fine-Tune  
Press  
to move, press OK button to confirm,  
to adjust.  
Frequency 874.37 MHz  
and press  
Save  
MENU  
NOTE:  
Picture Mode  
Standard  
Press red button to storage to channels  
after manual tuning .  
Color Temperature  
Aspect Ratio  
Noise Reduction  
Screen  
4). Program Edit:  
You can Delete, Rename, Move, or Skip any programs.  
PICTURE  
<
>
Programme Edit  
1
2
3
NOTE:  
1).Tint is available in NTSC system only.  
2).There are four color temperature modes  
can be selected, such as medium, warm, cool, and user.  
3).Screen is available in PC mode only, which  
can adjust horizontal position, vertical position,  
size and phase.  
Skip  
MENU  
Delete  
OK  
Rename  
Move  
-10-  
 
TV OPERATION  
3. SOUND MENU  
The third item of the MENU is the SOUND  
MENU.  
OSD Language  
English  
Restore Factory Default  
You can adjust the sound effect here such as  
treble, bass, balance etc.  
Blue Screen  
OSD Blend  
Press  
to move, press OK button to confirm,  
to adjust.  
OPTION  
<
>
and press  
Sound Mode  
Balance  
Standard  
Auto Volume  
Surround Sound  
NOTE:  
SOUND  
<
>
Restore factory default will clear all the programs  
and Reset all the settings to default value.  
6. USB FUNCTION  
You must enter the Source menu first,then choice the  
USB and press OK button,the USB menu will appear.  
Input Source  
Note:  
Auto volume: only available when the input  
signal volume is too large or distortion.  
TV  
YPBPR  
PC  
4. TIME MENU  
HDMI1  
HDMI2  
AV  
The forth item of the menu is the TIME MENU  
You can adjust the clock, power on/off time,  
sleep time etc.  
Press  
to move, press OK button to confirm,  
to adjust.  
USB  
and press  
OK  
Clock  
Off Time  
On Time  
Sleep Timer  
Auto Sleep  
TIME  
<
>
USB 2.0  
PHOTO  
MUSIC  
MOVIE  
TEXT  
NOTE:  
Within 15 minutes there is no signal, the TV  
will auto sleep.  
Once you power off the TV set by AC, the clock time  
will be reset.  
Please make sure that the USB device have plugged in  
the slot. There are four type media item can be selected,  
such as photo, music, Movie and text. Select the type  
media item by pressing  
the disk selection menu.  
, press OK button to enter  
5. OPTION MENU  
The fifth item of the MENU is the OPTION MENU.  
You can adjust the OSD language, Restore factory  
default, Blue Screen or OSD Blend.  
In the movie mode, when you use FB, FF function, The  
audio may be pause in several seconds to synchronize  
the audio signal and video signal.  
In text mode, press  
to make page up and page down.  
NOTE:  
When the USB device isn't supported, it may be that the  
power of the USB device isn't enough.  
-11-  
 
TV OPERATION  
Press  
to select the function icon, press OK button to  
confirm the function.  
1/1  
Press  
NOTE:  
or EXIT button to exit the control bar.  
You can adjust the audio track, subtitle, or program in  
the Info menu while Playing the video file.  
Choose the Info icon and press OK can display the Info  
MENU.  
Return  
C
Sample1.ts  
Press the  
to select the right disk and press OK to  
Resolution: 720x576  
display media files and folder list or choose Return to  
back to the media type selection menu.  
AudioTrack:  
Subtitle:  
1/2  
1/3  
1/6  
Program:  
1/1  
Size:  
30574 KBytes  
Resolution: 688x412  
R
AudioTrack: 1/2  
Subtitle:  
1/3  
1/5  
Program:  
Size: 511457 KBytes  
M
Sample1.ts  
Sample2.ts  
Close  
Sample1.ts  
Sample3.ts  
Sample4.ts  
Select the media file by pressing  
or  
, then  
the preview frame will pop up. Press the button  
to play the media file in full screen. When the  
media file (photo, music, Movie or text type) is  
playing, press the OK or Info button can display the  
control bar.  
Music function need to put music and picture in the  
same folder.  
-12-  
 
TV OPERATION  
Hotel Mode:  
Please press source key first,and then press number key  
“1001” to enter into Hotel Mode.  
HotelModeOperation  
OFF  
OFF  
100  
TV  
Hotel Mode Operation  
Panel key lock  
Maxvolume  
Start Source  
Start Channel  
1
Setup Menu display  
Input source change  
Save To USB  
Yes  
Yes  
Load  
Volume default  
0
Hotel Mode Operation: Set Hotel mode on/off.  
Panel key lock : Keypad will be locked, when Key Lock  
mode is on.  
Max volume: Set max volume limitted.This option allows  
you to set the Max Volume Level.  
Start SourceChoose source, the options as follow:  
TV/YPBPR/PC/HDMI1/HDMI2/AV/USB, press the or ►  
button to select the desired source.  
Start Channel : In TV mode, you can select a channel  
number to be set as the TV present channel. Press the or  
button to select the desired channel number .  
Setup Menu display :Main menu lock , main menu will not  
display when set to “No”  
Input source change : Source lockyou can't change the  
source, when set to “No”  
Save To USB: Backup all TV setting data to USB disk.  
(backup file named DATABASE.bin)  
Load: Restore this data to TV from USB disk. When  
restore is executedthe TV will reboot.  
Volume default : Power on default volume, press the or  
button to select the desired volume.  
-13-  
 
TROUBLE SHOOTING  
Trouble phenomenon  
Picture  
Audio  
Inspection  
antenna position, direction  
or connection  
Snow  
Noise  
antenna position, direction  
or connection  
Ghost  
Normal audio  
Noise  
electronic equipment,car/  
motorcycle,fluorescent light  
Interfere  
Volume(inspect wether the  
mute function on the remote  
control are started , or audio  
system are correct or not)  
Normal Picture  
Mute  
Power cord is not inserted  
Power switch is not opened  
Contrast and brightness/volume  
setup  
No picture  
No color  
Mute  
Press standby key on the remote  
control for inspecting  
Normal audio  
color control  
Normal audio  
or weak  
retune channel  
Scramble  
No color  
Audio system  
Noise  
Special ExplanationThe accessories such as remote control is not belongs  
to the guarantee。  
-14-  
 
 

Graco Baby Accessories PD261467A User Manual
Graco High Chair 3630 User Manual
Grandstream Networks Telephone Accessories GXW 400X FXS User Manual
Grizzly Nail Gun H5527 User Manual
HannsG Flat Panel Television HG281 User Manual
Havis Shields Automobile Accessories KK C VAK User Manual
Honeywell Satellite Radio STR93D User Manual
HP Hewlett Packard Spreader 918 User Manual
Husqvarna Chainsaw 1100 CD User Manual
Igloo Water Dispenser MWC496 User Manual