Specifications Information and Replacement Parts Manual
4445-95, 4446-95, 5570-95,
5571-95, 5572-95
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble,
operate or maintain the product described. Protect yourself and others by observing all safety information. The Safety Instructions are contained
in the General Operating Instructions. Failure to comply with the safety instructions accompanying this product could result in personal injury
and/or property damage! Retain instructions for future reference.
Vertical Sealless Sprayer/Washer
Pumps
Refer to form 1608-634-00 for General Operating and Safety Instructions and applicable Warranty.
Description
Vertical sealless sprayer/washer pumps are heavy duty industrial units designed for
OEM, automotive and industrial washing machines, parts cleaners, spray booths and
cooling towers. Pumps are immersion type; pump end must be immersed in liquid,
motor must remain above liquid surface.
All models feature 316 stainless steel semi-open clog resistant impeller, stainless steel
shaft, steel shaft coupling, cast iron base and column, plated steel inlet screen, and a
TEFC (Totally Enclosed Fan Cooled) electric motor. Motor has ball bearings. Heavy-
duty steel universal mounting brackets included. Pump design eliminates a bottom
bearing and a shaft seal on all models. Pumps handle liquids up to a maximum
temperature of 200° F. Maximum ambient temperature 104° F. Liquid viscosity cannot
exceed 100 SSU. These are manual units; no controls are supplied. For use with
nonflammable liquids compatible with pump component materials.
Specifications
DRIVER
NEMA DIS. Outlet
RPM Frame (Inches)*
Weight
(Lbs.)
78
73
165
150
130
Model
HP Power Supply
4445-95
4446-95
3
3
230 VAC, 60 Hz. 1-phase
230 VAC, 60 Hz. 3-phase
3450 56C
3450 56C
1-½
1-½
1-½
1-½
1-½
5570-95 10 230/460 VAC, 60 Hz. 3-phase 3450 184JM
5571-95 7.5 230/460 VAC, 60 Hz. 3-phase 3450 184JM
5572-95
5
230/460 VAC, 60 Hz. 3-phase 3450 184JM
NOTE: Driver data is subject to change without notice, see label on driver for actual specifications.
(*) Standard NPT (female) pipe thread
Performance Chart
GPM of Water at Total Head in Feet
Max.
Model
HP
3
3
60
80
80
*
70
55
55
115
80
25
25
100
90
-
-
100
-
-
50
110
120
130
140
150
Head†
85 ft.
85 ft.
110 ft.
4445-95
4446-95
5572-95
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5
80
5571-95 7.5
5570-95 10
*
*
*
*
140
*
125
162
110
150
90
135
70
120
40
95
-
70
-
40
140 ft.
160 ft.
(*) Operation of pumps beyond range indicated will result in reduced pump life, pump damage and/or motor damage.
(†) Shut-off; convert to psi, multiply by specific gravity and divide by 2.31
Installation
3. Position pump in tank or reservoir.
Position mounting brackets, align
pipe clearance hole with pump
discharge outlet.
(5570 series pumps)
1. (5570 series pumps) Remove
shipping fixture (Ref. No. 19) that
holds the drive shaft to the base
before installing pump.
4. Adjust lower fasteners (Ref. No. 4)
to bottom of mounting brackets.
Secure pump to mounting brackets
with upper fasteners (Ref. No. 4).
(4445 series pumps)
2. Pump must be installed with its
base supporting the entire weight of
the pump.
CAUTION Mounting brackets are
not designed to support the
pump’s weight. Brackets are
designed to prevent tipping.
4. Assemble one piece of sponge tape
(Ref. No. 25) to each clamp bracket
(Ref. No. 24). Attach clamp brackets to
mounting brackets with fasteners
provided (Ref. Nos. 26 and 27). This
will fix the column (Ref. No. 3) in
position.
5. Secure mounting brackets to tank
or reservoir. Install an appropriate
fastener in each hole or slot provided.
6. Install the balance of the system.
5570-250-00
03/2006
3
Repair Parts List
Ref.
Part Numbers For Models:
No.
1
2
3
4
5
Description
Motor
Coupling
Column
Washer
Fastener
4445-95
1626-075-00
4430-143-00
4430-032-09
*
4446-95
1626-076-00
4430-143-00
4430-032-09
*
*
Qty.
1
1
1
4
4
*
6
7
8
Fastener
Washer
Fastener
*
*
*
*
*
*
3
10
7
9
Impeller shim set (See 14)
10
Volute cover
4445-020-09
4440-020-01
1
11
12
13
14
15
Volute spacer plate
Fastener
Shaft
Impeller, Includes 9 & 15
Impeller nut
4445-060-09
*
4445-140-00
4445-010-98
1784-001-00
4445-060-09
*
4445-140-00
4445-010-98
1784-001-00
1
2
1
1
1
16
17
18
19
20
Gasket
4440-300-00
4445-001-95
N/A
N/A
Not available
4440-300-00
4445-001-95
N/A
N/A
Not available
1
1
1
-
Volute base, Includes 18
Debris screen (See 17)
N/A
Shaft support
1
21
Δ
Support plate
Mounting bracket kit
4445-090-09
4420-90
4445-090-09
4420-90
1
1
(Δ) Not shown.
(*) Standard hardware item, available locally.
N/A Not applicable to this model.
4
5570-250-00
03/2006
|