HP Hewlett Packard Network Router J8753A User Manual

Quick Start Guide  
5991-2113  
ProCurve Secure Router 7203dl  
J8753A  
Eth 0/2  
ProCurve 7203dl  
Slots  
Secure Router  
1
2
3
J8753A  
Stat  
Stat  
Stat  
Bkp  
Tx  
Bkp  
Tx  
Act  
Power  
Fault  
Test  
Rx  
Rx  
Console  
dl  
wide  
Eth 0/1  
dl  
dl  
INSTALL THE INTERFACE MODULE  
CONNECT TO THE PROCURVE SECURE ROUTER 7203DL CONSOLE  
1. Verify the unit is not connected to a power source.  
Before connecting to the ProCurve Secure Router 7203dl Console interface you will need the  
following items: VT100 terminal or PC (with VT100 terminal emulation software) and the serial  
cable (5184-1894) supplied with your router. (This is the same console cable used in other  
ProCurve switches such as the 5300xl series.)  
2. (Optional) To install the backup module, carefully align the P1 connector on the interface  
module with the J1 connector on the backup module. Using only fingertip pressure to  
ensure that neither circuit board bends or flexes, firmly seat the connectors. Secure the  
backup module to the interface module using the supplied screws and standoff posts.  
1. Connect the DB-9 (female) connector of your cable to the DB-9 DTE (male) Console  
interface on the front panel of the unit.  
3. Slide the interface module into the option slot until the module is firmly positioned  
against the chassis.  
2. Connect the loose end of the cable to the VT100 terminal or PC (with terminal emulation  
software).  
4. Secure the screws at both edges of the module.  
3. Open a VT100 terminal session to the ProCurve Secure Router 7203dl using the  
following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to  
activate the HP Command Line Interface.  
5. To install the wide module, align the module with the wide slot and slide the module into  
the chassis until it is firmly positioned against the backplane connectors. Secure by  
tightening the screws.  
4. Enter enable at the > prompt.  
GROUND THE ROUTER  
5. Enter the password when prompted or press <Enter> if you have not yet set a  
password.  
1. Strip one end of the ground wire to the length required for the ring terminal. (Ground wire  
and ring terminal are supplied by the user. For more detailed grounding specifications,  
please refer to the ProCurve Secure Router Installation Guide.)  
2. Crimp the ground wire to the ring terminal, using a crimp tool of the appropriate size.  
3. Attach the ring terminal to the chassis as shown in the figure to the right.  
4. Connect the other end of the ground wire to a suitable grounding point at your site.  
5. Apply power to the unit.  
For information on installing the Encryption and Compact Flash modules  
please refer to the ProCurve Secure Router Installation Guide included in  
Note  
your router shipment.  
61195890L1-13B, April 2005  
 
Copyright 2005 Hewlett-Packard Development Company, LP  

Graco Marine Radio 117256 Series C User Manual
Graco MP3 Player Accessories 3A2079A User Manual
Grizzly Grinder G2790 User Manual
Harbor Freight Tools Nail Gun 97520 User Manual
Honeywell Oven PW 6000 User Manual
Honeywell Photo Scanner 2020 User Manual
Hotpoint Freezer HT303NI User Manual
HQ Automobile Parts HQ 402 0606 User Manual
Husqvarna Chainsaw 235 User Manual
Husqvarna Trimmer 235FR User Manual