ELECTRIC 3⁄16" CROWN STAPLER
MODEL H3119
INSTRUCTION MANUAL
COPYRIGHT © OCTOBER, 2002 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
NOTICE
Safety Instructions
1. KEEP ALL SAFETY DEVICES IN
6. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear protective
hair covering to contain long hair.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from winch
before operation.
7. ALWAYS USE SAFETY GLASS-
ES. Also use face or dust mask if
cutting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
3. KEEP CHILDREN AWAY. All chil-
dren should be kept at a safe dis-
tance from winch.
4. DO NOT USE UNDER THE INFLU-
ENCE OF DRUGS OR ALCOHOL.
5. NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
8. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL.
H3119 Electric 3⁄16" Crown Stapler
-1-
Safety Instructions For Power Tools
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
9. USE PROPER EXTENSION CORD
for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
No list of safety guidelines can be
complete. Operating this tool may
require additional safety precau-
tions specific to your working
environment. Failure to use rea-
sonable caution while operating
this tool could result in serious
personal injury.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
H3119 Electric 3⁄16" Crown Stapler
-2-
INTRODUCTION
We are pleased to provide this manual with
Commentary
the Model H3119. It was written to encour-
age safety considerations and guide you
through general operating procedures and
maintenance. This manual represents our
effort to produce the best documentation
possible.
The specifications, details, and pho-
tographs in this manual represent the
Model H3119 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Lack of familiarity with this manual
could cause serious personal injury.
Spend a sufficient amount of time
becoming familiar the contents of
this manual, including all the safety
warnings.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
We are proud to offer the Grizzly Model
H3119 Electric 3⁄16" Crown Stapler. This
model is part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoy-
able operation and proof of Grizzly’s com-
mitment to customer satisfaction.
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
The Model H3119 is a high powered elec-
tric stapler capable of firing 20 gauge, 3⁄16"
1
crown staples in lengths ranging from ⁄4
"
9
to ⁄16". The quick loading magazine holds
85 staples and the weight is 3.25 lbs.
E-Mail: [email protected]
The Model H3119 is best suited for instal-
lation of carpet, insulation, ceiling tiles,
cabinets and HVAC systems.
H3119 Electric 3⁄16" Crown Stapler
-3-
OPERATION
Getting Started
Using The Stapler
Please take the time to become familiar
with this instruction manual. The informa-
tion contained will allow you to get the
maximum enjoyment and use from your
new tool.
DO NOT pull the trigger until the tip
of the stapler is against the surface
to be stapled. The stapler does NOT
have a safety mechanism.
Loading The Stapler
1. Be sure the stapler is loaded and the
The Model H3119 can hold up to 85 sta-
ples in the quick loading magazine.
magazine is closed securely.
2. Wear safety glasses when using the
To load the stapler:
stapler
1. Unplug the tool from the power
source!
3. Plug the stapler into a 110V power
source.
2. Press the silver lever while sliding back
4. Place the tip of the stapler against the
on the staple magazine.
workpiece and pull the trigger.
3. Point the tip of the stapler upward to
reveal the stapler loading area. The
loading area consists of a groove or
channel that runs along the bottom of
the stapler.
Avoid repeatedly shooting staples
into the exact same location without
moving the tip of the stapler. A staple
could become jammed in the tip of
the stapler.
4. Load a stick of 20 gauge 3⁄16" crown
1
9
staples ⁄4" to ⁄16" long into the loading
area.
5. Slowly slide the staple magazine back
into the closed position until the silver
lever latches in the closed position.
H3119 Electric 3⁄16" Crown Stapler
-4-
Clearing Jammed Staples
Maintenance
Staple jams are an inevitable part of oper-
ating any stapler.
Unplug the stapler from the power
source before performing any mainte-
nance!
To clear a jammed stapler:
Cleaning The Stapler
1. Unplug the tool from the power
source!
While wearing safety glasses, periodically
clean the stapler with compressed air. DO
NOT use flammable products to clean the
stapler.
2. Open the staple magazine and remove
all un-jammed staples.
3. The jammed staple may be easily
removed at this time; otherwise, the
stapler tip will need to be disassem-
bled.
4. To disassemble the tip, use an allen
wrench to remove the three allen head
cap screws from the face of the tip.
5. Once the screws are removed and the
staple magazine is open, the tip piece
should pull away from the stapler.
Gasoline or petroleum products used
to clean the tool could explode caus-
ing serious personal injury. DO NOT
use gasoline or petroleum products
to clean the tool.
6. The jammed staple should now be
easy to remove.
7. Once the jammed staple is removed,
re-assemble the stapler.
H3119 Electric 3⁄16" Crown Stapler
-5-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
H3119 Electric 3⁄16" Crown Stapler
-6-
REF PART #
DESCRIPTION
CYLINDER CAP ASSEMBLY
PLUNGER
REF PART #
DESCRIPTION
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PH3119001
PH3119002
PH3119003
PH3119004
PH3119005
PH3119006
PH3119007
PH3119008
PH3119009
PFH27
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
PH3119029
PH3119030
PH3119031
PH3119032
PH3119033
PH3119034
PSB41
SPRING
BASE
PIN
MAGAZINE SUPPORT
PIN
PLUNGER BLADE
PLUNGER RET. WASHER
RETURN SPRING
CLIP
E-CLIP
SUPPORT SPACER
SCREW 10-24 X 1/2"
LOCK NUT 10-32
POWER SUPPLY
LOCK WASHER #6
PHLP HD SCR 6-32 X 3/8"
INSULATION SLEEVING
LOCK NUT 6-32
FUSE HOLDER
LOCATOR RING
HANDLE (RIGHT)
FLAT HD ALLEN SCR 8-32 X 3/4"
LOCK NUT 8-32
CAP SCREW 8-32 X 7/8"
FLAT HD ALLEN SCR 8-32 X 1-5/16"
HANDLE (LEFT)
RING
PLN10
PH3119037
PLW08
PLN09
PS36
PSB67
PH3119040
PLN11
PFH28
PH3119014
PH3119015
PH3119016
PH3119017
PSB38
PH3119042
PSB69
CAP SCREW 6-32 X 3/8"
CORD ASSEMBLY
SWITCH PROTECTOR
SWITCH ASSEMBLY
CONTACT PIN
COIL/WASHER ASSEMBLY
STAPLER BODY
SCREW 10-32 X 3/8"
BUMPER
PH3119044
PH3119045
PH3119046
PH3119047
PH3119048
PH3119049
PLW01
PH3119019
PH3119020
PH3119021
PSB68
NOSE RETAINER
CLAMP
SPRING
TRIGGER BRACKET
LOCK WASHER 5/16"
HEX NUT 5/16"-24
SPRING
CAP SCREW 10-32 X 1/2"
SCREW 10-24 X 3/4"
PIN
PSB33
PN20
PH3119024
PH3119025
PH3119026
PH3119027
PH3119028
PH3119052
PH3119053
PH3119054
PH3119055
PH3119056
PH3119057
NOSE
CONTACT BUTTON
TRIGGER
PIN
PUSHER
RETAINING RING
TRIGGER PIN
MAGAZINE BASE
CARRYING CASE (NOT SHOWN)
H3119 Electric 3⁄16" Crown Stapler
-8-
NOTES
H3119 Electric 3⁄16" Crown Stapler
-9-
NOTES
H3119 Electric 3⁄16" Crown Stapler
-10-
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #___________________________ Serial #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT NAIL
|