Grizzly Kitchen Utensil H7779 User Manual

MODEL H7779  
JERKY SLICER  
INSTRUCTION SHEET  
Inventory (Figure 1)  
Disassembly for Cleaning  
You must disassemble the jerky slicer as shown  
in Figure 2 to clean all individual components  
thoroughly. Disassembly requires a 5mm hex  
wrench to remove the top half of the jerky slicer.  
A. Jerky Slicer................................................. 1  
B. Handle........................................................ 1  
C. Thumbscrew for Handle............................. 1  
D. Clamps ....................................................... 2  
E. Meat Alignment Combs.............................. 2  
You MUST clean, thoroughly rinse, and sani-  
tize all components of this product BEFORE  
and BETWEEN uses. Failure to follow this  
warning may lead to sickness or death!  
A
Figure 2. Required level of disassembly for  
proper cleaning of all components.  
C
B
When removing the crank arm shaft, be aware  
that the end is spring loaded (see Figure 3).  
D
E
This End Spring Loaded  
Figure 1. Model H7779 inventory.  
NOTICE  
The Model H7779 is NOT dishwasher safe!  
Figure 3. Overhead view of blade shafts.  
COPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC.  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
#TR7699 PRINTED IN CHINA  
 
Assembly  
1. Assemble the blade shafts as shown in  
Figure 3. When assembled correctly, the  
spring pushes the flat parts of the blades  
together. When replacing the blades on the  
main shaft (the one connected to the crank  
handle), make sure the beveled edge of the  
blades are facing the spring side. On the  
driven shaft, make sure the beveled sides of  
the blades are facing the gear side.  
2. Fasten the top half of the jerky slicer onto the  
base with the two cap screws.  
Figure 4. Inserting comb.  
3. Install the crank handle and secure it in place  
with the thumbscrew.  
4. Insert the meat alignment combs into each  
side of the slicer, as shown in Figure 4.  
5. Clamp the jerky slicer to the counter or table  
as shown in Figure 5. The maximum counter  
thickness that will work with the provided  
1
clamps is 1 ⁄2  
"
If you need additional help with this assembly, call  
our Tech Support at: (570) 546-9663.  
Operating  
Figure 5. Jerky slicer clamped to counter.  
This jerky slicer will accept pieces of meat up to  
1" thick and up to 434" wide. Cut larger pieces to  
fit before trying to insert them into the slicer. If you  
wedge too large of piece into the slicer, it may  
get stuck or place undue pressure on the cutting  
components.  
Make your kitchen “child  
safe.” Ensure that the jerky  
slicer is inaccessible to chil-  
dren by storing out-of-reach  
or locking it away. Never  
allow children to use this  
jerky slicer without the direct  
supervision of a responsible  
adult.  
To slice meat, insert the piece of meat into the  
opening and turn the handwheel. NEVER INSERT  
FINGERS INTO THE OPENING! If a piece of  
meat becomes stuck, use a fork to remove it or  
remove the top for easier access.  
If you intend to slice different kinds of meat  
at the same time, clean the slicer between  
meat types to avoid cross contamination.  
 
H7779 Parts Breakdown and List  
�  
 
�  
�  
�  
 
 
 
�  
 
��  
 
 
�  
�  
�  
�  
�  
�  
��  
�  
��  
�  
�  
�  
�  
�  
�  
�  
�  
�  
�  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PH7779001 FUNNEL  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
PH7779017 CLAMP  
2
PH7779002 STAINLESS CAP SCREW M6-1 X 12  
PH7779003 STAINLESS FLAT WASHER 6MM  
PH7779004 UPPER HOUSING  
PH7779018 STAINLESS CAP SCREW M6-1 X 10  
PH7779019 GEAR ASSEMBLY  
3
4
PH7779020 PLASTIC GEAR BUSHING 13MM  
PH7779021 SPECIAL STAINLESS WASHER 13MM  
5
PH7779005 STAINLESS PHLP HD SCR M5-.8 X 16  
PH7779006 COMB  
6
PR47M  
EXT RETAINING RING 13MM  
7
PH7779007 DRIVEN SHAFT  
PH7779023 PLASTIC BUSHING 30MM  
PH7779024 PLASTIC BUSHING 29MM  
PH7779025 PLASTIC BUSHING 25MM  
PH7779026 COMPRESSION SPRING  
PH7779027 BUSHING CAP  
8
PH7779008 MAIN SHAFT  
9
PH7779009 CRANK HANDLE  
10  
11  
12  
13  
14  
15  
16  
PH7779010 HANDLE THUMB SCREW  
PH7779011 STAINLESS CAP SCREW M6-1 X 8  
PH7779012 RIGHT LEG  
PH7779028 DRIVEN SHAFT BUSHING  
PH7779029 MAIN SHAFT BUSHING  
PH7779030 BLADE  
PH7779013 BASE  
PH7779014 STAINLESS CAP SCREW M5-.8 X 10  
PH7779015 LEFT LEG  
PH7779031 PLASTIC BUSHING 40MM  
PH7779016 LOWER HOUSING  
 

Gravely Lawn Mower 785006 User Manual
Gravely Lawn Mower 915146 ZT34 User Manual
Hamilton Beach Air Cleaner 840088700 User Manual
Hans Grohe Plumbing Product 06094000 User Manual
HeadsetUSA Portable Speaker PAS 400 User Manual
Honeywell Video Gaming Accessories TrueSTEAM User Manual
Hotpoint Microwave Oven 6665 User Manual
HP Hewlett Packard Grill Accessory 3300 3400 User Manual
HP Hewlett Packard MP3 Player M8201R User Manual
IFB Appliances Washer AW60 9021 User Manual