™
Failure to follow these warnings a
could result in seriou
Easy-Entry
Battery Swing
OWNER’S
MANUAL
Model No. __________
Serial No. __________
Dear Customer,
Please fill in the model
and serial numbers
above from the label
beneath the motor
of your new swing.
Never leave child unattended.
Always keep your child in view.
Model No. 1602
Congratulations on your purchase of a
Graco® swing!
Graco is the recognized leader in the
design and manufacture of quality baby
swings. We believe your new Graco®
swing is a wise choice, promising many
hours of enjoyment for your baby.
Before using your swing, please take a
few minutes to read this Owner’s Manual.
The short time you spend reading these
instructions will help you use your swing
properly.
Strings can cause strangulation.
STRANGULATIO
DO NOT place sw
location where th
such as window b
drapes, phone co
DO NOT place items with a string
around your child’s neck, such
as hood strings or pacifier cords.
DO NOT suspend strings over the
swing or attach strings to toys.
Please save your Owner’s Manual
for future use.
Customer Satisfaction
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY.
If you experience any difficulties, please contact the
Customer Service Department.
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call may
be processed quickly and efficiently.
DO NOT USE SWING without the seat cover.
DISCONTINUE USING YOUR SWING should it become
damaged or broken.
© 1999 Graco 132-7-99 IS1651
2
Attaching the Legs
Attaching the Hanger Tubes and Seat
Step 1.
Step 1.
Hold tube
vertically
Move seat back fully forward
onto seat armrests.
Push oval end of the upper
leg sections firmly onto the
four plastic pegs. Hold tube
vertically while pushing in.
Push leg on completely.
Flattened
side
Plastic peg
The seat back must overlap
the armrests.
Step 2.
Seat back
Push the leg tips on the
round ends of the lower leg
sections. (The other ends
have a wire.)
Armrest
Step 3.
Wire end
Put the wire end of lower leg
sections into the round end
of the upper leg sections.
Push the sections together
while twisting lower leg
slightly. This will ensure a
snug fit.
Round
end
(not oval)
Step 2.
Slide hanger tubes into
armrests of seat as shown.
Step 3.
Step 4.
Insert two pin screws
through seat armrests
into the holes in the
hanger tubes and
tighten securely.
CHECK:
Lift swing as shown. If legs
are assembled properly, the
legs will dangle from the
motor unit and not fall off.
IF LEG FALLS:
Step 4.
Holding leg vertically, push
leg firmly up while pushing
the motor unit down.
Insert the hanger tubes
into the hanger brackets
as shown. Metal buttons
should pop out and lock
upon full insertion.
Step 5.
CHECK that the
hanger tubes are
secure in hanger
brackets by pulling
firmly on them.
Open the swing legs
completely. Snap plastic leg
braces onto outside of legs.
The plastic pins inside the
ends of the braces will fit into
the dimples on the legs.
Dimple
It may be necessary to
spread the legs as shown.
Push
Do not use
swing without the leg
braces.
Push
132-7-99 IS1651
5
6
Attaching the Back Brace
Attaching the Seat Belt
Step 1.
Working behind the seat,
snap the four pins in the
ends of the plastic back
brace into the holes in
the hanger tubes.
Thread one end of the
seat belt through the belt
retainer as shown.
Slide adjustment wire
through openings in seat
back, then insert ends
into back brace holes as
shown.
Step 2.
Thread both ends of seat belt
through the buckles as shown.
CHECK that the belt is threaded
correctly by pulling on the seat
belt. The belt should not slip
through the buckle.
Be sure the back brace
is securely attached by
pulling on it.
To release, push in on front of
buckle.
Attaching the Tray
Place one hand on the armrest and slide the tray onto the
hanger tube with other hand. Push sleeve of tray all the
way into the armrest of the seat until you hear it snap.
Attaching the Seat Cover
Step 1.
Sleeve on tray must snap completely into the armrest.
Pull firmly on tray to be sure it is securely attached.
Slide the pocket of the seat
cover over the top of the seat
as shown.
Step 2.
Pull crotch strap and both ends
of the seat belt through the slots
in the seat cover.
Step 3.
Push the elastic loop through
the hole on one side of seat.
Step 4.
Fold cover around bottom of
seat. Then fasten the hook into
the elastic loop on one side as
shown. Repeat on other side.
CAUTION: Be sure the seat
cover at armrest does not
interfere with tray latching.
Push sleeve
all the way
into armrest
7
8
Toy Mounting System
Installing Batteries
Your swing has a toy mounting system in the tray. This
swing model does not come equipped with toys. If you
would like to order toys, please see the enclosed leaflet
for information. Please insert the two plastic covers as
described below to fill the holes in the tray.
NEVER INSERT OR REMOVE THE
BATTERIES WITH BABY IN THE SEAT. THEY COULD
FALL ON BABY IF DROPPED!
Step 1.
With baby out of swing,
open the battery compartment
by gently pressing on the lid at
the ridged area and lifting the
lid.
To Install Covers
To insert a cover into the tray of
your swing, first push one side into
a notch, then push in the other side.
Step 2.
Insert four “D” cells. CHECK
that the batteries are put in
correctly. (Swing will not run if
batteries are put in backwards.)
Step 3.
Using the Tray
Snap the lid closed.
If tray does not latch, check back brace to be sure the
word “REAR” is away from the seat.
Step 1.
Unlatch the tray by squeezing
the two latches under the tray at
the same time, and lift up the
tray. Be careful not to let the
tray hit your baby when lifting or
closing the tray.
Starting Swing
CHECK that all parts are securely fastened together
before using the swing.
Step 1.
Step 2.
Open tray and seat belt. Place baby in the seat. (If your
child is very small, you may want to use rolled-up blankets
as a prop.)
To latch tray, push down firmly.
Tray must be
latched at all times when baby
is in the swing. Pull up on
tray to be sure it is latched.
Step 2.
Place crotch strap between
child’s legs and snap both
side buckles to the center
buckle. Adjust belt as needed to
get a snug fit around your child.
Reclining Back—
Four Positions
Step 3.
Close the tray. CHECK that tray is
latched by lifting up on the tray.
Pull adjustment wire upward
and pull seat backward to
recline seat. Extra pressure
is needed to go from third
position to full recline.
Do not depend
on the tray or seat belt alone to
hold your baby. Always secure
your baby with both the seat
belt and tray when your baby
is in the swing.
For upright position, simply lift
back of seat forward.
132-7-99 IS1652
9
10
Step 4.
FOR SAFE BATTERY USE:
Adjust the control switch to
medium setting.
Do not remove or insert the batteries with
baby in swing. The batteries could fall on
baby if dropped.
Step 5.
Keep the batteries out of children’s reach.
PUSH SWING SEAT TO START. BE SURE YOU PUSH IT
UP HIGH ENOUGH FOR THE MOTOR TO GET A GOOD
START.
Any battery may leak battery acid if mixed with
a different battery type, if inserted incorrectly
(put in backwards) or if all batteries are not
replaced or recharged at the same time.
Observe the swinging motion for a minute. It takes time for
your swing to adjust to a new setting.
Any battery may leak battery acid or explode
if disposed of in fire or an attempt is made to
charge a battery not intended to be recharged.
Never recharge a battery of one type in a
recharger made for a battery of another type.
For a lower speed, push the control switch toward “low.”
•
•
For a higher speed, push the control switch toward “high.”
A small, quiet baby will swing higher on each setting than a
larger, more active baby.
Discard leaky batteries immediately. Leaky
batteries can cause skin burns or other per-
sonal injury. When discarding batteries, be
sure to dispose of them in the proper manner,
according to your state and local regulations.
Indicator Light-
ON/OFF light comes on
when swing is turned on.
Always remove batteries if the swing is not going to be used
for a month or more. Batteries left in the unit may leak and
cause damage.
Recommended Type Batteries–Size D
Your seat may be stopped at any time the motor is
running without damaging the motor. Push swing
to restart.
!
Rechargeables–Use and recharge according to
!
manufacturer’s instructions.
!
Disposables–Alkaline.
!
NEVER mix battery types.
If your swing motor stops operating by itself, a
protective device may have been activated. Turn
off motor, wait three minutes, then restart swing.
Change batteries when swing ceases to operate satisfactorily.
Caring for Your Battery Powered Swing
Problem: Possible Reasons for Problem:
Swing
won't
operate
1. No batteries in swing.
2. Batteries dead.
3. Speed setting too low.
4. Batteries in backwards—check “+” and “-”.
5. Corrosion on battery terminals. Rotate batteries
in place against terminals, or clean with
sandpaper or steel wool if corrosion is severe.
6. Baby leaning too far forward.
7. Baby grabbing swing legs. (Discontinue use.)
8. Seat not pushed high enough for a good start.
9. Protective device activated. (Turn off motor,
wait 3 minutes, then restart swing.)
Seat
1. Control setting too low.
doesn't
swing
very
2. Blanket hanging down, causing increased
wind resistance.
3. Batteries too weak.
high
4. Baby leaning too far forward.
5. Baby too heavy or too active. (Discontinue use.)
6. Soft carpet (swings higher on hard floors).
If you still have problems, call our toll-free
number, 1-800-345-4109.
11
12
Replacement Parts
Instructions for ordering swing parts:
Complete form below. Your swing model number MUST
be included on the form to ensure proper replacement
parts. Your model number can be found on a sticker
beneath the swing motor. Payment must accompany
your order.
Parts List:
Price:*
Motor unit..................... $25.00
Hanger tube ................ $13.00 (each)
Plastic seat................... $20.00
with strap & buckle
Cloth seat cover........... $14.00
Seat belt ...................... $15.00
Hardware...................... $15.00
Plastic leg brace........... $15.00 (each)
Adjustment wire............ $17.00
Back brace................... $17.00
Upper leg section......... $17.00 (each)
Lower leg section......... $17.00 (each)
Leg tips (set of 4)......... $15.00
Tray.............................. $12.00
* Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions or if you need any part
not listed, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P. O. BOX 100, MAIN STREET
ELVERSON, PA 19520
Model Number SHIP TO:
(Must be filled in)
Name
Motor unit
Hanger tube
Plastic seat
Address
with strap & buckle
Cloth seat cover
Seat belt with buckle
Hardware
Plastic leg brace
Adjustment wire
Back brace
City, State, Zip
(
)
Telephone
Check enclosed
Upper leg section
Lower leg section
Leg tips (set of 4)
Tray
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Total:
Shipping
& handling:
$5.00 Account #:
6% sales tax
(PA only):
Expiration date:
Signature:
Total amount
due:
132-7-99 IS1652
13
|