Instructions - Parts
Circulation and
Return Tube Kits
309852E
ENG
For recirculation of polyurethane materials from proportioner to 55 gal. (200
liter) fluid supply drums.
4000 psi (27.6 MPa, 276 bar) Maximum Fluid Working Pressure
Description
Carbon Steel
Stainless Steel
Return Tube Kit
246477
246978
24E379
24D106
Circulation Kit
Circulation Kit With Moisture-Lok Hose
24D107
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
™
246978 Kit shown installed in Reactor proportioning
system. Some parts shown are not included in kit.
TI3465a
Circulation Kit
Circulation Kit
1. Install two return tube
kits, page 2
2. Connect circulation kit
Remove fittings from elbows (A, B) at the pro-
portioner fluid manifold. Only used with 24697
For 246978: Screw reducing nipples (104) into
elbows. Connect one end of hoses (102) to
each nipple.
CAUTION
To prevent cross-contamination of fluid, mark A com-
ponent (ISO) connections with red tape. Mark B com-
ponent (RES) connections with blue tape. Do not
interchange or cross-connect A component and B
component parts.
For 24E379 and 24D107: Connect elbows (105)
to the proportioner fluid manifold. Connect fitting
(106) to return tube. Connect one end of hoses
(102) to each elbow.
E
Connect other end of A side hose (102) to
elbow (E) of A component return tube kit.
Repeat for B side hose.
106
102
Ref.
No.
101
Part No. Description
Qty
2
2
102 † H45010 HOSE, fluid; nylon; 1/2 in. (13 mm)
ID; 1/2 npsm(fbe); 10 ft (3.05 m)
◆ 262176 HOSE, B; 1/4 in. (6.35 mm) ID; (10
ft (3.05 m)
2
2
TI15106a
★ 262239 HOSE, B; 1/4 in. (6.35 mm) ID; (10
ft (3.05 m)
104 † 162449 NIPPLE, reducing; 1/2 x 1/4 npt
105 ◆ 122311 FITTING, elbow; 9/16-18 JIC 06 x
1/4 npt
2
2
★ 122786 FITTING, elbow; 9/16-18 JIC 06 x
1/4 npt
2
106 ◆ 124151 FITTING, 9/16-18 JIC 06 x 1/2 npt
★ 124152 FITTING, 9/16-18 JIC 06 x 1/2 npt
2
2
† 246978 Circulation Kit only.
◆ 24E379 Circulation Kit only.
★ 24D107 Circulation Kit only.
246978 Circulation Kit
24E379 and 24D107 Circulation Kit
A
105
104
102
102
B
104
105
102
102
TI15107a
TI3510a
309852E
3
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 309852
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MIINNEAPOLIS, MN 55440-1441
Copyright 2003, Graco Inc. is registered to ISO 9001
Revised 04/2010
|