GE Universal Remote 20309 User Manual

20309  
Universal Remote  
Instruction Manual  
 
Setup  
Battery Installation  
1. On the back of the remote, push down on the tab and lift the  
cover off.  
2. Match the batteries to the + and - marks inside the battery  
case, then insert 2 AAA Alkaline batteries.  
3. Press the battery cover back into place.  
Battery Saver  
Your remote automatically turns off if the buttons are depressed  
more than 30 seconds. This will save your batteries should your  
remote get stuck in a place where the buttons remain depressed  
(e.g., between the sofa cushions).  
Code Saver  
You will have up to 10 minutes to change the batteries in your  
remote without losing codes you have programmed. However, do  
not press any buttons until batteries are installed in the remote. If  
buttons are pressed without batteries in the remote, all codes will  
be lost.  
Code Setup  
The SETUP button is used to setup the remote. You can  
either setup the remote using the code for your brand of  
product, from the code tables (on separate sheet), or you  
can search through the library of codes until you find a  
code that works for your product. Please refer to “Programming  
with Code Search” page 9 for more information on using the code  
search feature to learn how to search through the library of codes  
for your products. NOTE: You can store any kind of code under any  
mode (except TV). I.E. you can store a VCR code under the CBL/SAT  
button, or a DVD code under the VCR button, etc. However, you can  
only store TV codes under the TV button.  
3
 
Button Functions  
Some buttons on the remote might have functions that are referred  
to by different names on the device you are controlling. E.G. PREV.  
CH may be called RECALL, or ENTER may be called DISPLAY. These  
differences depend on the brand and model of your product. Also,  
this remote can only operate features that exist on your product.  
E.G., your product must have PREV.CH ability for the PREV.CH but-  
ton to operate this feature.  
TV, VCR, etc. selects  
SETUP for  
Red Indicator  
product to be operated.  
setup.  
Lights when any  
button is pressed.  
INPUT for some TVs, press  
repeatedly to select  
from available viewing  
sources (antenna, cable  
box, VCR, etc.).  
PREV.CH Returns to the previously  
selected channel, or DVD repeat toggle.  
REPEAT performs DVD players “A-B  
Repeat” (or RPT A.B) function for repeat  
play of current Chapter or Track.  
RECORD, PLAY, STOP, REW, FF, PAUSE  
VCR control buttons operate your VCR  
even when the remote is set to operate  
the TV. Also operates DVD Scan -/+.  
Note the VCR keys also control DVD  
when in DVD Mode.  
ENTER for some TV models,  
used after direct channel  
number entry to immediately  
change to the selected channel.  
MENU selects the  
on-screen menu.  
GUIDE displays satellite or cable  
on-screen program guide.  
4
 
Button Functions, cont.  
Turns Backlight  
on and off.  
ON•OFF Turns product  
On or Off.  
CHANNEL Up/Down Changes  
the channels TRACK +/- controls  
DVD/CD track selection i.e. DVD/  
CD Track Skip Up/Down (in DVD  
and CD modes).  
INFO/DISPLAY button brings up  
DVD Display or Control Menu for  
Chapter/Track/Title number, Time  
remaining/elapsed indication,  
system information, etc.  
VOLUME UP/DOWN changes  
the volume level of the product,  
normally the TV.  
CC (SUBTITLE) TV Closed  
Caption (if your TV has  
this feature) or DVD  
Subtitle toggle.  
MUTE Turns off the  
TV sound while the  
picture remains.  
NUMBERS enter numbers for  
direct channel selection. Some  
products require ENTER to  
be pressed after channel  
selection.  
Dot used for digital  
channels like 2.3.  
OK Selects menu items for the  
device you are controlling.  
RESUME, AUDIO, ZOOM, ANGLE,  
TITLE controls DVD functions.  
Note: The REC button must be pressed TWICE to record from your VCR. For some brands  
of VCRs, you might need to press the REC button once, then press it again for three  
seconds.  
5
 
DVD Functions  
This remote has several dedicated buttons used for DVD functions.  
The descriptions may vary from your original remote descriptions.  
SCAN+ and SCAN- buttons control the speed of Fast Forward and  
Reverse Playback respectively.  
SKIP (Channel Up & Down) buttons respectively locate the succeed-  
ing or preceding Chapters or Tracks on a disc.  
SUBTITLE (CC) Turns the subtitles on or off.  
TITLE Brings up the DVD Title Menu screen.  
REPEAT A-B button performs DVD players “A-B Repeat” (or RPT A.B)  
function for repeat play of current Chapter or Track.  
INFO/DISPLAY button brings up DVD Display or Control Menu for  
Chapter/Track/Title number, Time remaining/elapsed indication,  
system information, etc.  
MENU brings up the DVD disc Menu screen - use with the UP,  
DOWN, LEFT & RIGHT navigation buttons.  
OK button is used for on-screen Menu selection. Note some DVD  
players require the Play button to be used.  
EXIT Exit On-Screen Menus and/or Return to previous On-Screen  
selection.  
PLAY button is used to start Disc playback and for Menu selection  
on some DVD players.  
STOP button stops Disc playback.  
PAUSE button pauses Disc playback - press PLAY to resume.  
OPEN/CLOSE Opens or closes the disc tray.  
GUIDE/PROG Program the playback order of chapters or tracks on  
your disc.  
AUDIO selects the audio language or sound during disc playback.  
SETUP/INPUT brings up the DVD Players Setup Menu.  
RESUME Continues disc playback from where you stopped (if sup-  
ported by your DVD player).  
ANGLE selects the viewing angle during disc playback.  
ZOOM Zoom or enlarge a specific area of the screen.  
Note, not all DVD Players support all the functions described above.  
6
 
SAT Functions  
GUIDE/PROG button displays on-screen Satellite Channel Guide.  
CHANNEL+ and CHANNEL- buttons perform the “Page+” and  
Page-” function for on-screen Guide Menus used by some Satellite  
systems.  
INFO/DISPLAY button brings up Satellite Display screen for current  
Channel and system information.  
MENU brings up the Satellite Menu screen - use with the UP,  
DOWN, LEFT & RIGHT navigation buttons.  
OK button is used for on-screen Menu selection.  
EXIT button is used to Exit or Clear on-screen Menu displays.  
INPUT/SETUP button performs the Satellite TV/SAT function.  
7
 
Direct Code Entry  
1. Press and hold the SETUP button until the red indicator  
stays on, then release the SETUP button.  
2. Press and release the desired mode button (TV, VCR,  
etc.). The red indicator blinks, then stays lit.  
3. Enter the 4 digit code from the code tables (on  
separate sheet). Note: after  
a valid code entry, the red  
indicator turns off. For an  
invalid code, the red indicator  
flashes.  
4. With your device on, press  
ON•OFF. If the device turns  
off, no further programming  
is required. Note: If some  
buttons do not operate your  
equipment, try one of the  
other codes for your brand.  
Write your codes down here for easy reference later.  
Device  
Device stored  
Code  
TV  
TV  
DVD  
VCR  
CBL/SAT  
AUDIO  
AUX  
8
 
Code Search  
If your device does not respond after you have tried all the codes  
for your brand, or if your brand is not listed, try searching for your  
code by following these steps.  
1. Manually turn on the device (TV, VCR, etc.) to be  
controlled.  
2. Press and hold the SETUP button until the red indicator  
stays on, then release the SETUP button.  
3. Press and quickly release the desired mode button  
(TV, VCR, etc.). The red indicator blinks off once.  
4. Press the ON•OFF button repeatedly (up to 300  
times) until the device to be controlled turns off.  
The red indicator blinks off with each button press.  
5. Press and release ENTER to install the code.  
Most users will store VCR codes under the VCR button,  
Cable codes under CABLE, etc. If (for example) you want to store a  
VCR code under CABLE, first follow the procedure for Direct Code  
Entry (page 8) and press CABLE in step 2 of Direct Code Entry, then  
enter ANY VCR code in step 3 of Direct Code Entry. Then follow the  
steps above for Code Search.  
Note: If the device does not have a CHANNEL UP button, use PLAY  
(VCR only) or POWER instead. Code Search starts from the currently  
stored 4 digit number under that mode. Sometimes the first code  
that “works” with your device may only allow limited functionality  
(e.g. the MENU button might not work). There may be a code that  
performs more functions. Continue the code search process until  
the best code is found.  
9
 
Using Your Remote  
Code Identification  
The Code Identification Feature allows you to identify the 4 digit  
library code stored under your device key. For example, if you want  
to find out what 4 digit code is stored under your TV device key,  
follow the six steps below:  
1. Press and hold the SETUP button until the red indicator  
stays on. Release the SETUP button.  
2. Press and release the desired mode button (TV, VCR,  
etc.). The red indicator blinks, then stays lit.  
3. Press and release the SETUP button. The red  
indicator blinks once and remains lit.  
4. To find the first digit for the code stored under the  
mode key pressed in step 2, press each numeric key  
from 0-9 in turn. The number that causes the indicator  
light to blink is the first digit  
in your code.  
5. To find the second digit,  
repeat step 4, this time when  
the red indicator blinks off  
this is the second digit.  
6. Repeat step 4 to find the third  
and fourth digits.  
10  
 
Using Your Remote, cont.  
Controlling Devices with Separate Power On and Off Buttons  
Some GE, RCA and ProScan models require you to press the device  
button for more than one second to turn the device on and the  
POWER button to turn the device off.  
Controlling Combo Devices  
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will  
require you to set up two different Mode buttons to control both  
parts of the Combo device. For example, if you have a TV/DVD  
Combo, you might need to set up one code under the TV button to  
control the TV part AND a separate code (under any other Mode  
button) to control the DVD part.  
VCR/DVD Punch-Through  
This remote allows the 6 VCR transport buttons (i.e. PLAY, PAUSE,  
STOP, FF, REWIND, and REC) to Punch-Through control from any  
Mode programmed with TV, SAT or Cable codes to the last VCR, or  
DVD programmed Mode you used. This feature will not operate if  
the programmed TV, SAT or Cable code has its own VCR transport  
button control e.g. a TV Combo, SAT/PVR, etc.  
11  
 
Using Your Remote, cont.  
Volume/Mute Control and Punch-Through  
This remote lets you select which device Mode controls your  
Volume/Mute buttons. The remote is initially set for all device  
Modes to use their own Volume/Mute control if present. If the  
programmed code has no Volume/Mute operation of its own then  
those buttons will punch-through control to the TV Mode device  
without needing to change to TV Mode.  
Any Mode chosen for Volume/Mute control MUST have its own  
Volume/Mute function or the Volume/Mute buttons will do  
nothing.  
Setting ALL Volume/Mute Control to any one Mode  
This routine can set all Modes to “punch-through” to any one  
chosen Mode for Volume/Mute button control without the needing  
to change to that Mode.  
1. Press and hold the SETUP button until the red indicator  
turns on, then release the button.  
2. Press and hold the MUTE button until the red indicator  
blinks off, then release the button.  
3. Press and release the desired Mode button (TV, VCR,  
etc.) for Volume/Mute control, the red indicator blinks  
then stays on.  
4. Press and release the MUTE button and the red  
indicator turns off. The red indicator will blink rapidly  
for three seconds if the Mode you have selected has no  
Volume/Mute control.  
All other Modes will now punch-through to your chosen Mode for  
Volume/Mute control.  
12  
 
Using Your Remote, cont.  
Setting any Mode to use its own Volume/Mute Control  
This routine can set any Mode to use only its own Volume/Mute  
control. Note - If your chosen Mode has no Volume/Mute functions  
of its own then the Volume/Mute buttons will do nothing.  
1. Press and hold the SETUP button until the red indicator  
turns on, then release the button.  
2. Press and hold the MUTE button until the red indicator  
blinks off, then release the button.  
3. Press and release the desired Mode button (TV, VCR,  
etc.), the red indicator blinks then stays on.  
4. Press and release the VOLUME- (Down) button, the  
red indicator blinks then stays on.  
5. Press and release the MUTE button and the red  
indicator turns off.  
Your chosen Mode will now use its own Volume/Mute  
control.  
13  
 
Troubleshooting  
Remote does not operate your product.  
Press the mode button of the product you want to control.  
Program the remote with a new code.  
Install new batteries. (You might have to reprogram your  
remote after installing new batteries.)  
Remote may not be compatible with your product.  
Remote does not operate some features of your product.  
Sometimes a particular code might operate some features but  
not all. Try programing remote with a new code.  
Remote may not be able to operate all features of your product  
or button names might be different than your product.  
Red Indicator blinks after you program a product code.  
Remote did not accept the code.  
Try to program the code again or try a different code.  
If you lose your codes or programming instructions, you can find  
14  
 
90 Day Limited Warranty  
Jasco Products Company warrants this product to be free from  
manufacturing defects for a period of ninety days from the original  
date of consumer purchase. This warranty is limited to the repair  
or replacement of this product only and does not extend to  
consequential or incidental damage to other products that may be  
used with this unit. This warranty is in lieu of all other warranties  
express or implied. Some states do not allow limitations on how  
long an implied warranty lasts or permit the exclusion or limitation  
of incidental or consequential damages, so the above limitations  
may not apply to you. This warranty gives you specific rights, and  
you may also have other rights which vary from state to state. If  
unit should prove defective within the warranty period, return  
prepaid with dated proof of purchase to:  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114  
15  
 
20309  
Universal Remote  
Instruction Manual  
Jasco Products Company  
10 E. Memorial Road  
Oklahoma City, OK 73114  
Made in China  
20309-03/09  
 

ELAN Home Systems VCR V883 User Manual
Five Star Ranges Ventilation Hood FSH301 BL User Manual
Frigidaire Washer 134533800A User Manual
Furman Sound Stereo Equalizer RR 131 User Manual
GE Air Conditioner AGE07AJ User Manual
GE Dishwasher 165D4700P207 User Manual
Gefen Switch EXT DPKVM 841 User Manual
GE Oven JKS10DP User Manual
Gianni Industries Door EB 262 User Manual
Global Machinery Company Impact Driver ATI2K User Manual