GE Door 19214 User Manual

reference). Remove the old chime.  
2. Install new chime  
a. Remove the front cover from the chime.  
b. Pull the pushbutton and transformer wires through the slot in the base of chime.  
c. Mark the 4 holes using the base as a template with the arrow pointing up.  
d. If using the screw anchors, drill 4 - 5/32”holes and insert the plastic screw anchors.  
Otherwise drill a 3/64” pilot hole for the screws.  
Chime Tune Setting  
The following instructions explain how to  
change the tune on the wired chime.  
1. Remove the chime cover and locate the  
two 3 position dip switches shown below.  
Wired Chime  
Installation Instructions for  
Wired Chime  
Front Door Dip Switch  
e. Mount the chime base using the 4x25mm screws.  
f. Attach the two wires from each pushbutton as shown in the wiring diagram. For each push  
button, one wire should be connected to the “Common” screw and one wire should be  
connected to the “Front” or “Rear” screw.  
g. Attach the wires from the chime transformer to the “transformer connections” as shown in  
the wiring diagram. (There is no polarity requirement).  
h. Slide the front cover on the back plate of the chime.  
Power Requirement: 16VAC @ 180mA  
maximum  
Rear  
Door  
Button  
Front  
Door  
Button  
Wiring Diagram  
Rear Door Dip Switch  
Chime  
2. Select the desired chime sound from  
the table below.  
Included hardware:  
(1) Chime  
(4) Plastic screw anchors  
(4) 4x25mm screws (for anchors)  
Chime Sound Table  
Position  
1
2
3
Required Tools:  
Westminster  
Ding Dong  
Knock  
Bronze Chime  
Cuckoo Clock  
Foghorn  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
Wire stripper/cutter, small flat blade  
screwdriver, Phillips screwdriver, drill,  
and drill bit (5/32”)  
Removing Front Cover  
The following instructions explain how to  
remove the front cover of the wired  
chime.  
Gong  
For technical support contact Jasco  
Products Company at 1-800-654-8483  
Made in China  
ON: Switch On (up)  
OFF: Switch Off (down)  
1. With the cover face down hold the  
front cover while sliding the back plate  
to the left.  
2. Using your finger gently pry up on the  
back cover plate. The back plate with  
the paper product label should come  
away easily.  
Hecho en China  
WARNING: Do not exceed 16VAC  
input to the chime.  
is a trademark of General Electric Company and is used under license to  
Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114.  
Installation  
1. Remove the cover from the old door  
chime, disconnect the transformer and  
Rev. 08-13-08  
 
19214-2  
pushbutton wires (label them fo  
r

Eclipse Fujitsu Ten Car Stereo System CD3100 User Manual
Eizo Computer Monitor HD 2411W User Manual
Everpure Water Dispenser Sparkling Chilled Water Dispenser User Manual
EVGA Computer Hardware 132 BL E758 User Manual
Firstech LLC Two Way Radio 2W900FMR 2ND 5P User Manual
Frigidaire Washer FAFS4272LA User Manual
Fujitsu Network Card MB2142 03 User Manual
Furuno Telephone FS 5070 User Manual
GE Clothes Dryer GLD4600 50 60N User Manual
GE Monogram Cooktop ZEU30R User Manual