Fujitsu Printer FTP 642MCL001 User Manual

24V DRIVE, HIGH SPEED LINE THERMAL PRINTER  
4” MECHANISM, WITH OR WITHOUT CUTTER  
FTP-642MCL001/002  
FTP-642MCL301/302  
OVERVIEW  
FTP-642MCL/FTP-622DCL Series is an ultra high speed line thermal  
printer driven by 24 VDC, printing on 4-inch wide paper (112 mm/114  
mm) .  
This printer is compact and light weight, and the design allows easy  
head maintenance, head cleaning and head replacement.  
This printer is suitable for a variety of applications, such as POS  
terminals, ticket machines, coupon machines, label printers, medical  
instruments, etc. A printer with a specially designed cutter is also  
available.  
FTP-642MCL001  
HIGHLIGHTS  
• Ultra high speed printing  
It can print at 80 mm/s (640 dotlines/s) maximum by using Fujitsu  
Components' unique head drive control.  
• Compact and lightweight  
This printer has a low profile of only 20 mm, and a light weight of  
approximately 125 g.  
• Low power consumption  
The peak current for head driving is approximately 4.1 A (at 80  
mm/s printing speed, 50% printing ratio).  
FTP-622CU101  
• Easy head access  
It is designed for easy head cleaning and head replacement.  
• Paper auto loading function  
Thermal paper can be loaded without head-up lever operation.  
• ESC/POSTM*1 Commands  
The commands conform to ESC/POSTM.  
• Auto Cutter  
Printer with auto cutter (full cut/partial cut ) is also available.  
• UL Recognized  
File No.E171434  
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.  
FTP-622DCL001  
1
 
FTP-642MCL001/002/301/302  
(Continued)  
Item  
Specifications  
Part number  
Interface  
FTP-642MCL001/002  
FTP-642MCL301/302  
Centronics (ESC/POSTM), RS232C  
24VDC ± 5%, Voltage  
2
Current : average*  
(
): Peak  
For head  
1.61 (2.03) A (at 80 mm/s printing speed, 25% printing ratio)  
1.17 (2.03) A (at 50 mm/s printing speed, 25% printing ratio)  
1.08 (1.16) A (at 30 mm/s printing speed, 25% printing ratio)  
Power supply  
For motor  
24VDC ± 5%, 1.0 A maximum  
24VDC ± 5%, 1.0 A maximum  
For cutter  
----------  
For logic  
5VDC ± 5%, 0.5 A maximum  
138 (W) × 48 (D) × 20 (H) mm (excluding lever)  
131 (W) × 89 (D) × 24 (H) mm  
approximately 125 g  
Mechanism (cutter)  
Interface board  
147 (W) × 69 (D) × 42 (H) mm (w/cutter)  
Dimension  
Weight (Mechanism+Cutter)  
Mechanism  
approximately 450 g (w/cutter)  
Pulse durability : 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard  
driving method)  
Wear resistance  
: 50 km (at 25% printing ratio)  
Expected life  
Cutter  
----------  
3 × 105 cuts  
3
Operating temperature 0 to +50°C*  
Environmental  
conditions  
Operating humidity  
Storage temperature  
Storage humidity  
Head temperature  
Paper out/Mark detect  
Head-up  
20 to 85% RH (no condensation)  
–20 to +60°C (excluding paper)  
5 to 95% RH (no condensation)  
By thermistor (applied energy control, abnormal temperature detection)  
By photointerrupter  
Detection  
By microswitch  
For front insertion use (112 mm width) : FTP-040PU001, FTP-040P0701  
For rear insertion use (114 mm width) : FTP-040P0020, FTP-040P0702  
*Recommended papers  
Recommended thermal sensitive paper  
· Oji paper  
· NIPPON paper  
· MITSUBISHI paper Mills  
: PD150R, PD160R, PD170R  
: TF50KS-E,TF60KS-E,TF60KJ-R  
: P220VBB-1, AFP-235  
*1: There may be exceptions.  
*2: 24 VDC, minimum head resistance.  
*3: Guarantee: +5°C ~+40°C.  
3
 
FTP-642MCL001/002/301/302  
DIMENSIONS  
Mechanism  
PAPER INSERTION(MCL001)  
HEAD UP LEVER(AT HEAD DOWN)  
20.1  
CENTER OF PAPER  
PAPER  
INSERTION  
(MCL002)  
HEAD CONNECTOR  
106.4(POSITIONING HOLE PITCH)  
+
1
71.8–  
65.7  
Unit: mm  
(137.5)  
Mechanism with cutter  
3—M 3(FIXING HOLE FROM UPPER SIDE)  
CENTER OF PAPER  
MCL301  
PAPER  
INSERTION  
MCL302  
PAPER  
INSERTION  
93.0  
106.4(POSITIONING H0LE)  
73.0  
147  
71.8±1  
(75.3)  
(80.6)  
Note: all dimensions are nominal value.  
Unit: mm  
4
 
FTP-642MCL001/002/301/302  
Interface board  
130.8  
120.7  
116.8  
87.6  
19.1  
5.1  
5.1  
CN2**  
CN5  
CN3  
4—ø3.6  
CN10  
CN11*  
CN13  
5.1  
5.1  
43.2  
86.4  
105.4  
120.7  
*CN11 on FTP-622DCL011/111 & 622DSL011/012/112 only  
**CN2 on FTP- 622DSL only  
Unit: mm  
5
 
FTP-642MCL001/002/301/302  
CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM  
1. Thermal Head  
Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent  
Board side: PHR-16 (J.S.T.) or equivalent  
No. Signal Comment  
1
2
VH  
VH  
Power for head  
Power for head  
3
GND Head ground  
4
GND Head ground  
5
STB1 Print enable signal 1  
STB2 Print enable signal 2  
STB3 Print enable signal 3  
6
7
8
TH*1  
STB4 Print enable signal 4  
LAT Print data latching signal  
Temperature detection  
9
10  
11  
12  
13  
14  
15  
16  
STB5 Print enable signal 5  
VDD Power for logic  
CLK  
DIN  
Data transmission clock  
Print data output signal  
GND Head ground  
VH Power for head  
*1: Symbol: " " means a negative logic signal  
Thermal head heat sink  
Motor  
Head up level  
1, 2, 3, ......................................15, 16  
Connector Pin No.  
2. Motor connectors  
3. Sensor connectors  
Motor side : PHR-4 (J.S.T.) or equivalent  
Board side : B4B-PH-K-S (J.S.T.) or equivalent  
Sensor  
: PHR-5 (J.S.T.) or equivalent  
Board side : B5B-PH-K-S (J.S.T.) or equivalent  
No. Signal Comment  
No. Signal Comment  
1
2
3
4
B
B
A
A
Stepping motor coil excitation  
Stepping motor coil excitation  
Stepping motor coil excitation  
Stepping motor coil excitation  
1
2
3
4
5
VSEN Power for paper sensor  
PHE Photo interrupter emittor  
PHK Photo interrupter cathode  
SW1 Head up detect switch 1  
SW2 Head up detect switch 2  
6
 
FTP-642MCL001/002/301/302  
4. Cutter  
Mech side : EHR-4 (J.S.T.) or equivalent  
Board side : B4B-EH (J.S.T.) or equivalent  
No Cable Color  
Name  
1
2
3
4
White  
White  
Red  
Home position 1  
Home position 2  
Motor energizing signal M+  
Motor energizing signal M-  
Black  
FUNCTION  
ITEM  
ITEM  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Test printing  
8.  
Cutter trouble detection  
Motor power save  
Paper-out detection  
9.  
10.  
11.  
12.  
13.  
14.  
Paper near end detection  
Mark detection  
Head-up detection  
MCU trouble detection  
Power on/off sequence protection  
Motor protection  
Abnormal temperature detection of thermal head  
Blown fuse detection  
Abnormal voltage detection of head  
Hardware timer  
INTERFACE, COMMAND, OPTIONS  
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and  
Options.  
Europe  
Japan  
Fujitsu Components Europe B.V.  
Diamantlaan 25  
2132 WV Hoofddorp  
Netherlands  
Fujitsu Component Limited  
Gotanda-Chuo Building  
3-5, Higashigotanda 2-chome, Shinagawa-ku  
Tokyo 141, Japan  
Fujitsu Components  
International  
Headquarter  
Offices  
Tel: (31-23) 5560910  
Fax: (31-23) 5560950  
Tel: (81-3) 5449-7010  
Fax: (81-3) 5449-2626  
Asia Pacific  
North and South America  
Fujitsu Components America, Inc.  
250 E. Caribbean Drive  
Sunnyvale, CA 94089 U.S.A.  
Tel: (1-408) 745-4900  
Fujitsu Components Asia Ltd.  
102E Pasir Panjang Road  
#04-01 Citilink Warehouse Complex  
Singapore 118529  
Tel: (65) 6375-8560  
Fax: (1-408) 745-4970  
Fax: (65) 6273-3021  
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered  
trademarks of their respective owners. Rev. 11/15/2004.  
7
 

Fostex Portable Speaker FW405N User Manual
Frigidaire Film Camera FHWC3025M S W B User Manual
Fujitsu Air Conditioner AOU12RL2 User Manual
Fundex Games Board Games My MASH Destiny Diary Game User Manual
Garmin GPS Receiver 18X User Manual
Garmin GPS Receiver TBM850 User Manual
GE Double Oven 49 4540 User Manual
Gefen TV Cables ext hdboost 141 User Manual
GE Freezer FCM5SU User Manual
GE Monogram Oven ZSC1201 User Manual