FieldServer Computer Drive FS 8700 84 User Manual

A Sierra Monitor Company  
Driver Manual  
(Supplement to the FieldServer Instruction Manual)  
FS-8700-84 Lutron eLumen  
APPLICABILITY & EFFECTIVITY  
Effective for all systems manufactured after May 1, 2001  
 
FS-8700-84_Lutron_eLumen Manual  
Table of Contents  
4.1.26. System Control Commands containing no Parameters: Toggle system  
variable value....................................................................................................................... 20  
4.1.27. System Control Commands containing no Parameters: Output temp scene  
21  
4.1.28. System Control Commands containing no Parameters: Select scene in  
area  
22  
4.1.29. System Control Commands containing no Parameters: Timeclock new  
schedule 23  
4.1.30. System Control Commands containing no Parameters: Set timeclock...... 23  
4.1.31. System Control Commands containing no Parameters: Enable  
wallstation(s)......................................................................................................................... 24  
4.1.32. System Control Commands containing no Parameters: Disable  
wallstation(s)......................................................................................................................... 24  
4.1.33. System Control Commands containing no Parameters: Simulate  
wallstation(s) switch press ................................................................................................. 25  
4.1.34. System Control Commands containing no Parameters: Simulate  
wallstation(s) switch release.............................................................................................. 26  
4.1.35. System Control Commands containing no Parameters: Stop scene ramp  
down  
26  
4.1.36. System Control Commands Containing Parameters: Toggle zone............ 27  
4.1.37. System Control Commands Containing Parameters: Fade zone(s) to level  
27  
4.1.38. System Control Commands Containing Parameters: Ramp zone(s) up ... 28  
4.1.39. System Control Commands Containing Parameters: Ramp zone(s) down  
28  
4.1.40. System Control Commands Containing Parameters: Pommel or pulse  
zone(s Toggle zone) ........................................................................................................... 29  
4.1.41. System Control Commands Containing Parameters: Flash zones aka  
“Multi level ( Flash or Warn or Chase )........................................................................... 30  
4.1.42. System Control Commands Containing Parameters: Ramp scene zones  
up  
4.1.43. System Control Commands Containing Parameters: Ramp scene zones  
down 31  
30  
4.1.44. System Control Commands Containing Parameters: Select system  
scene(s) using override times............................................................................................ 31  
4.1.45. System Control Commands Containing Parameters: Set system variable  
value  
32  
4.1.46. Listening to switch presses and releases: Enabling switch presses and  
releases reporting................................................................................................................ 32  
4.1.47. Listening to switch presses and releases: Disabling switch presses and  
releases reporting................................................................................................................ 32  
4.1.48. Listening to switch presses and releases: Listening to switch presses and  
releases 33  
4.1.49. Active read on startup: Retrieving names....................................................... 34  
Appendix A. Data Tables..................................................................................................... 35  
Appendix B. Revision History............................................................................................ 36  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 1 of 36  
1.  
Lutron eLumen Description  
The Serial Lutron eLumen driver allows the FieldServer to transfer data to and from  
devices over RS-232 or RS-485 using eLumen protocol. The FieldServer can only be  
used operationally as a Lutron Client driver. Any existing Lutron Server drivers are for  
FieldServer testing purposes only and cannot be used to emulate a Lutron eLumen  
system.  
The driver supports the following 3 panels: GRAFIK5000, GRAFIK6000 and  
GRAFIK7000. The hardware for all 3 panels is identical. The only differences are limits  
in the database. GRAFIK5000 has only 1 CSD link and can have a max of 128 zones.  
GRAFIK6000 has 3 CSD links with 512 zones. GRAFIK7000 has 6 links with 512  
zones and can communicate with other processors.  
The FieldServer eLumen driver implements the following functionality:  
ƒ Status monitoring of eLumen system data and parameters.  
ƒ System Control of eLumen.  
Status monitoring is achieved by sending status requests to the eLumen system.  
Retrieved status data are collected and stored in FieldServer Data Arrays that allow  
access by other protocols.  
System Control Commands can be configured in the FieldServer to address any groups  
of Areas, Zones or Scenes. A mechanism is provided by which the parameters are set  
before the command is triggered using the upstream protocol.  
Commands are provided to read the names of Areas, Zones and Scenes from the  
eLumen to facilitate access by SCADA systems.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 2 of 36  
2.  
Driver Scope of Supply  
1.01  
Supplied by FieldServer Technologies for this driver  
FieldServer Technologies  
PART #  
Description  
FS-8915-10  
FS-8917-02  
FS-8700-84  
UTP cable (7 foot) for RS-232 use  
RJ45 to DB9F connector adapter  
Driver Manual.  
1.02  
Provided by the Supplier of 3rd Party Equipment  
2.1.1.  
Required 3rd Party Hardware  
Part #  
Description  
Lutron Panel  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 3 of 36  
3.  
Hardware Connections  
The FieldServer is connected to the Lutron eLumen as shown in connection drawing.  
Configure the eLumen according to manufacturer’s instructions  
FS-8917-02  
LUTRON SERIAL  
RS-232 INTERFACE  
PART # 470-784  
8917-02 WIRE LIST  
CAT 5 CABLE  
FS-8915-10  
FUNCTION  
RX  
FROM  
TO  
COLOUR  
WHITE  
BROWN  
YELLOW  
GREEN  
RED  
BLACK  
ORANGE  
BLUE  
RJ45-01  
RJ45-02  
RJ45-03  
RJ45-04  
RJ45-05  
RJ45-06  
RJ45-07  
RJ45-08  
DB9M-02  
DB9M-08  
DB9M-06  
DB9M-05  
CTS  
DSR  
GND  
GND  
DTR  
RTS  
TX  
DB9M-04  
DB9M-07  
DB9M-03  
Serial  
Power OK  
(408)-262-2299  
Tx  
EIA232  
Rx Tx  
Rx  
-
+
Ethernet  
USB  
EIA485  
LUTRON ELUMEN RS-232  
CONNECTION DIAGRAM  
FS-B2010  
BASE NAME:  
FILE NAME: FS-T28700-84 .VSD  
DATE: 11/12/04  
BY: MC  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 4 of 36  
120V 15A  
Dedicated Control  
Feed  
Wallstation link  
To control stations  
To dimmer panels  
eLumen  
Processor  
Aux Link (RS-485)  
User Interface link  
Dimmer panel link  
Inter-processor link  
Serial  
Power OK  
Tx  
EIA232  
Rx Tx  
Rx  
-
+
Ethernet  
USB  
EIA485  
FS-B2010  
(408)-262-2299  
LUTRON ELUMEN RS-485  
CONNECTION DIAGRAM  
BASE NAME:  
FILE NAME: FS-T28700-84 .VSD  
DATE: 11/12/04  
BY: MC  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 5 of 36  
4.  
Configuring the FieldServer as a Lutron eLumen Client  
For a detailed discussion on FieldServer configuration, please refer to the FieldServer  
Configuration Manual. The information that follows describes how to expand upon the  
factory defaults provided in the configuration files included with the FieldServer (See  
“.csv” sample files provided with the FieldServer).  
This section documents and describes the parameters necessary for configuring the  
FieldServer to communicate with a Lutron eLumen Server  
1.03  
Data Arrays/Descriptors  
The configuration file tells the FieldServer about its interfaces, and the routing of  
data required. In order to enable the FieldServer for Lutron eLumen  
communications, the driver independent FieldServer buffers need to be declared in  
the “Data Arrays” section, the destination device addresses need to be declared in  
the “Client Side Nodes” section, and the data required from the Servers needs to be  
mapped in the “Client Side Map Descriptors” section. Details on how to do this can  
be found below.  
Note that in the tables, * indicates an optional parameter, with the bold legal value  
being the default.  
Section Title  
Data_Arrays  
Column Title  
Function  
Legal Values  
Up to 15 alphanumeric  
characters  
Data_Array_Name  
Provide name for Data Array  
Float, Bit, UInt16,  
SInt16, Packed_Bit,  
Byte, Packed_Byte,  
Swapped_Byte  
Provide data format. Each Data  
Array can only take on one  
format.  
Data_Array_Format  
Data_Array_Length  
Number of Data Objects. Must  
be larger than the data storage  
area required by the Map  
Descriptors for the data being  
placed in this array.  
1-10,000  
Example  
// Data Arrays  
Data_Arrays  
Data_Array_Name,  
Area_status,  
Zone_list,  
Data_Format,  
UInt16,  
UInt16,  
Data_Array_Length  
64  
64  
10  
Zone_pars,  
UInt16,  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 6 of 36  
1.04  
Client Side Connection Descriptions  
Section Title  
Connections  
Column Title  
Function  
Specify which port the  
device is connected to the  
FieldServer  
Legal Values  
P1-P8, R1-R21  
Port  
Protocol  
Baud*  
Parity*  
Specify protocol used  
Specify baud rate  
Specify parity  
eLumen  
9600 – Vendor limitation  
None  
Data_Bits*  
Stop_Bits*  
Specify data bits  
Specify stop bits  
Specify hardware  
handshaking  
8
1
Handshaking*  
Poll _Delay*  
None  
Time between internal polls 0-32000 seconds, 1 second  
Example  
// Client Side Connections  
Connections  
Port, Protocol,  
Baud, Parity, Data Bits, Stop Bits, Poll_Delay  
9600, None, None, 1, 0.100s  
P1,  
eLumen,  
1.05  
Client Side Node Descriptors  
Section Title  
Nodes  
Column Title  
Function  
Legal Values  
Up to 32 alphanumeric  
characters  
Node_Name  
Node_ID  
Provide name for node  
The eLumen processor  
address - only decimal values  
allowed e.g. 11 hex has to be  
entered as 17.  
0-255  
Protocol  
Port  
Specify protocol used  
eLumen  
P1-P8, R1-R21  
Specify which port the device is  
connected to the FieldServer  
Specifies the eLumen  
Node_type  
Hex, decimal  
command and data format  
1
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction manual for  
details of the ports available on specific hardware.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 7 of 36  
Example  
// Client Side Nodes  
Nodes  
Node_Name,  
LUT_GRF6_0,  
Node_ID, Protocol,  
17, eLumen,  
Connection, Node_type  
P1,  
hex  
1.06  
Client Side Map Descriptors  
The driver uses Map Descriptors with Lutron commands to build poll messages that  
will be sent to the eLumen system. Example Map Descriptors are shown in the next  
section. Note the following in the use of Map Descriptors for the Lutron driver:  
Lutron command  
Every Map Descriptor must have a Lutron command specified so the driver will know  
which command to send to the eLumen.  
Function  
Map Descriptor functions must be correctly specified to implement the functionality  
embodied by the specific Lutron command, e.g. a command to retrieve area status  
requires a read Map Descriptor whereas a command to toggle zones requires a  
write Map Descriptor.  
DA_Area_Names, DA_Scene_Names, DA_Zone_Names, xxx_Offset  
These are user Map Descriptor fields needed to retrieve area, scene and zone  
names from the eLumen. Please refer to the Map Descriptor examples.  
Link, Area, Link_station, Switch, Zone, Sys_var, Panel  
These are user Map Descriptor fields that must be used as needed with a specific  
Lutron command. Please refer to the Map Descriptor examples.  
DA_Lut_List, DA_Lut_List_Offset  
Lutron commands that allow multiple areas, zones, etc to be specified in one  
command e.g. Toggle zones use the areas or zones in the Data Array specified by  
DA_Lut_List at an offset specified by DA_Lut_List_Offset to build the poll message.  
The list must be filled in before the command is triggered by writing into the Data  
Array specified by Data_Array_Name.  
DA_Lut_Parms, DA_Lut_Parms_Offset  
Lutron commands that use parameters such as delay and fade cycles use the  
parameters at the offset as specified by these Map Descriptor fields. Parameters  
must be filled in together with the list data if applicable before triggering the  
command by writing into the Data Array specified by Data_Array_Name. Please  
refer to the Map Descriptor examples.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 8 of 36  
4.1.1.  
FieldServer Related Map Descriptor Parameters  
Column Title  
Function  
Name of this Map  
Descriptor  
Name of Data Array  
where data is to be  
stored in the  
Legal Values  
Up to 32 alphanumeric  
characters  
Map_Descriptor_Name  
Data_Array_Name  
One of the Data Array  
names from “Data Array”  
section above  
FieldServer  
0 to maximum specified in  
“Data Array” section  
above  
ARS, RDBC, WRBC,  
WRBX, AWT  
Starting location in  
Data Array  
Data_Array_Location  
Function  
Function of Client  
Map Descriptor  
4.1.2.  
Driver Related Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
One of the node names  
specified in “Client Node  
Descriptor” above  
Name of Node to fetch  
data from  
Node_Name  
Specifies the command  
to be sent to the  
eLumen.  
A list of commands is  
provided in Appendix A.  
GRAFIK_command  
0–11 for  
GRAFIK_command:  
ena_wallstation,  
dis_wallstation,  
sim_ws_sw_press,  
sim_ws_sw_rls,  
Link  
Wallstation link number  
0-31 for  
GRAFIK_command:  
wallstation_status,  
switch_status,  
GRAFIK system area  
number  
Wallstation on link’s  
number  
Wallstation switch  
number  
GRAFIK system zone  
number  
Area  
0–511  
0–31  
Link_station  
Switch  
Zone  
0–31  
0–511  
GRAFIK system variable  
number  
GRAFIK panel number  
Sys_var  
Panel  
0–65535  
0–511  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 9 of 36  
Column Title  
Function  
Legal Values  
Any Data Array name. If  
not listed under Data  
Arrays the driver will  
auto-create the Data  
Array.  
Name of Data Array that  
contains a list of zones  
or areas, etc, needed to  
build the poll message.  
DA_Lut_List  
The offset into the  
DA_Lut_List Data Array  
where the driver will  
retrieve the list data  
when building the poll  
message.  
0 to the maximum offset  
into the DA_Lut_List  
Data Array.  
DA_Lut_List_Offset  
DA_Lut_Parms  
Any Data Array name. If  
not listed under Data  
Arrays the driver will  
auto-create the Data  
Array.  
Name of Data Array  
containing parameters  
needed to build the poll  
message.  
The offset into the  
DA_Lut_Parms Data  
Array where the driver  
will retrieve the  
parameters when  
building the poll  
message.  
0 to the maximum offset  
into the DA_Lut_Parms  
Data Array.  
DA_Lut_Parms_Offset  
DA_Area_Names  
Any Data Array name. If  
not listed under Data  
Arrays the driver will  
auto-create the Data  
Array.  
Name of Data Array  
where retrieved area  
names will be stored.  
The offset into the  
DA_Area_Names Data  
DA_Area_Names_Offset Array where retrieved  
0 to the maximum offset  
into the  
DA_Area_Names Data  
Array.  
area names will be  
stored.  
Any Data Array name. If  
not listed under Data  
Arrays the driver will  
auto-create the Data  
Array.  
Name of Data Array  
where retrieved scene  
names will be stored.  
DA_Scene_Names  
The offset into the  
DA_Scene_Names Data  
Array where retrieved  
scene names will be  
stored.  
0 to the maximum offset  
into the  
DA_Scene_Names Data  
Array.  
DA_Scene_Names_Offs  
et  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 10 of 36  
Column Title  
Function  
Legal Values  
Any Data Array name. If  
not listed under Data  
Arrays the driver will  
auto-create the Data  
Array.  
Name of Data Array  
where retrieved zone  
names will be stored.  
DA_Zone_Names  
The offset into the  
DA_Zone_Names Data  
Array where retrieved  
zone names will be  
stored.  
0 to the maximum offset  
into the  
DA_Zone_Names Data  
Array.  
DA_Zone_Names_Offse  
t
Start and end numbers  
of area name to be  
retrieved with  
Area_Names_Start  
Area_Names_End  
0–511  
get_names cmd  
Start and end numbers  
of scene name to be  
retrieved with  
Scene_Names_Start  
0–32,768  
0–511  
Scene_Names_End  
Zone_Names_Start  
get_names cmd  
Start and end numbers  
of zone name to be  
retrieved with  
Zone_Names_End  
get_names cmd  
Length of Map  
Descriptor. The length is  
an indication of the  
number of data elements  
this Map Descriptor is  
responsible for updating.  
It is used in the overall  
points calculation of the  
FieldServer.  
See example Map  
Descriptors for individual  
lengths per Map  
Descriptor.  
Length  
4.1.3.  
Column Title  
Scan_Interval  
Timing Parameters  
Function  
Legal Values  
0s to 32000s  
Rate at which data is polled  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 11 of 36  
4.1.4.  
System Monitor Command – Time Now  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Length  
Time_now, 5s, Time_now, 0, rdbc, LUT_GRF6_0, time_now,  
1
Data storage in Data Array  
Position from offset Description:  
0
Minutes from midnight  
4.1.5.  
System Monitor Command – Astro Times  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
Astro_times, 5s, Astro_times, 0, rdbc,  
GRAFIK_command, Length  
LUT_GRF6_0, astro_times,  
2
Data storage in Data Array  
Position from offset  
Description:  
0
1
Sunrise minutes from midnight  
Sunset minutes from midnight  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 12 of 36  
4.1.6.  
System Monitor Command – Date  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Length  
Date, 5s, Date, 0, rdbc, LUT_GRF6_0, date,  
4
Data storage in Data Array  
Position from offset  
Description:  
0
1
2
3
Month ( 1-12 )  
Day of month ( 1-31 )  
Year ( 0-99 )  
Day of week ( 1-7, 1=Sunday )  
4.1.7.  
System Monitor Command – Code Revision Level  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Length  
Code_rev,  
5s,  
Code_rev,  
0,  
rdbc,  
LUT_GRF6_0, code_rev_level,  
1
Data storage in Data Array  
Position from offset  
0
Description  
Code revision level  
4.1.8.  
System Monitor Command – Bootcode Revision Level  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Length  
Bootcode_rev,  
5s,  
Bootcode_rev,  
0,  
rdbc,  
LUT_GRF6_0, bootcode_rev_level,  
1
Data storage in Data Array  
Position from offset  
0
Description  
Bootcode revision level  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 13 of 36  
4.1.9.  
System Monitor Command – Serial Number  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Length  
Serial_num, 5s, Serial_num, 0, rdbc, LUT_GRF6_0, serial_no,  
1
Data storage in Data Array  
Position from offset  
0
Description  
Serial number  
4.1.10.  
System Monitor Command – Area Status  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Area, Length  
Area_sts_00,  
Area_sts_01,  
1s,  
1s,  
Area_status,  
Area_status,  
0,  
2,  
rdbc,  
rdbc,  
LUT_GRF6_0, Area_status,  
LUT_GRF6_0, Area_status,  
0,  
1,  
2
2
Data storage in Data Array  
Position from offset  
Description  
0
1
System scene on status  
Sequence running status  
Note: This command stores 2 data values. To prevent overlaps, remember to increment Data_Array_Offset by 2 when referencing the same Data  
Array with other Map Descriptors.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 14 of 36  
4.1.11.  
System Monitor Command – Timeclock Status  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Tclk_sts_00,  
Tclk_sts_01,  
Scan_Interval, Data_Array_Name,  
Data_Array_Offset, Function, Node_Name,  
GRAFIK_command,  
Area, Length  
1s,  
1s,  
Tclk_status,  
Tclk_status,  
0,  
4,  
rdbc,  
rdbc,  
LUT_GRF6_0, timeclock_status,  
LUT_GRF6_0, timeclock_status,  
0,  
1,  
4
4
Data storage in Data Array  
Position from offset  
Description  
Schedule number  
0
1
2
3
Next event type (1 = no more events, 2 = timeclock disabled, 3 = astronomic event, 4 = realtime event )  
Next event time ( minutes past midnight )  
Next script  
Note: This command stores 4 data values. To prevent overlaps, remember to increment Data_Array_Offset by 4 when referencing the same Data  
Array with other Map Descriptors.  
4.1.12.  
System Monitor Command – Zone Intensity  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zn_int_00,  
Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Zone, Length  
1s,  
1s,  
Zone_int,  
Zone_int,  
0,  
1,  
rdbc,  
rdbc,  
LUT_GRF6_0, zone_intensity,  
LUT_GRF6_0, zone_intensity,  
0,  
1,  
1
1
Zn_int_01,  
Data storage in Data Array  
Position from offset  
0
Description  
Zone intensity ( 0-127 )  
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data  
Array with other Map Descriptors.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 15 of 36  
4.1.13.  
System Monitor Command – Request Panel Emergency Status  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Panel, Length  
Pnl_emerg_sts_00,  
Pnl_emerg_sts_511,  
1s,  
1s,  
Pnl_emerg_sts,  
Pnl_emerg_sts,  
0,  
511,  
rdbc,  
rdbc,  
LUT_GRF6_0, pnl_emerg_status,  
LUT_GRF6_0, pnl_emerg_status,  
0,  
511,  
1
1
Data storage in Data Array  
Position from offset  
Description  
0
Panel emergency status  
0 = normal; 1 = override  
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data  
Array with other Map Descriptors.  
4.1.14.  
System Monitor Command – System Variable Value  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Scan_Interval, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, Sys_var, Length  
Sys_var_00,  
Sys_var_01,  
1s,  
1s,  
Sys_vars,  
Sys_vars,  
0,  
1,  
rdbc,  
rdbc,  
LUT_GRF6_0, sys_var_val,  
LUT_GRF6_0, sys_var_val,  
0,  
1,  
1
1
Data storage in Data Array  
Position from offset  
0
Description  
System variable value  
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data  
Array with other Map Descriptors.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 16 of 36  
4.1.15.  
System Monitor Command – Wallstation Status  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Wall_st_sts_0000,  
Wall_st_sts_0001,  
Scan_Interval,  
1s,  
1s,  
Data_Array_Name,  
Wall_st_sts_00,  
Wall_st_sts_00,  
Data_Array_Offset,  
0,  
32,  
Function,  
rdbc,  
rdbc,  
Node_Name,  
LUT_GRF6_0,  
LUT_GRF6_0,  
GRAFIK_command,  
wallstation_status,  
wallstation_status,  
link,  
0,  
0,  
link_station,  
0,  
1,  
Length  
32  
32  
Data storage in Data Array  
Position from offset  
0-31  
Description  
All switches on station and their priority.  
Note: This command stores 32 data values. To prevent overlaps, remember to increment Data_Array_Offset by 32 when referencing the same  
Data Array with other Map Descriptors.  
Implementation note: The wallstation status command retrieves the status of all 32 switches defined on a wallstation. If you only want to retrieve  
the status of a few individual switches, rather only use the switch status Map Descriptor as described below.  
4.1.16.  
System Monitor Command – Switch Status  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Sw_sts_000,  
Sw_sts_001,  
Scan_Interval,  
1s,  
1s,  
Data_Array_Name,  
Sw_sts_00,  
Sw_sts_00,  
Data_Array_Offset,  
0,  
1,  
Function,  
rdbc,  
rdbc,  
Node_Name,  
LUT_GRF6_0,  
LUT_GRF6_0,  
GRAFIK_command,  
switch_status,  
switch_status,  
link,  
0,  
0,  
link_station,  
0,  
0,  
switch,  
0,  
1,  
Length  
1
1
Data storage in Data Array  
Position from offset  
Description  
0
Switch status and priority  
Note: This command stores 1 data value. To prevent overlaps, remember to increment Data_Array_Offset by 1 when referencing the same Data  
Array with other Map Descriptors.  
Implementation note: The switch status command only retrieves the status of one switch on a wallstation. To retrieve other switch statuses, use  
additional switch status Map Descriptors or else use the wallstation status Map Descriptor to retrieve the status of all 32 switches. When using  
both wallstation status and switch status Map Descriptors in the same configuration, it is not permissible to have the target Data Arrays overlap.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 17 of 36  
4.1.17.  
System Control Commands containing no Parameters: – Halt Zone  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zone_halt,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
0,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
halt_zone,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-63  
Description  
Zone(s) to halt  
Note: After setting up the zone numbers to halt in the DA_Lut_List Data Array, trigger this command by writing the number of zones to halt into the  
Data Array specified by Data_Array_Name at an offset specified by Data_Array_Offset.  
4.1.18.  
System Control Commands containing no Parameters: – Stop Scene Ramp Up  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Stop_scn_rmp_up,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
1,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
stop_scene_ramp_up,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area(s) with scenes to stop ramp up  
Note: After setting up the area numbers to stop scene ramps in the DA_Lut_List Data Array, trigger this command by writing the number of areas  
into the Data Array specified by Data_Array_Name at an offset specified by Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 18 of 36  
4.1.19.  
System Control Commands containing no Parameters: – Select System Scene(s)  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Sel_scene,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
2,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
sel_scene,  
DA_Lut_List,  
Scene_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-63  
Description  
System scenes to select  
4.1.20.  
System Control Commands containing no Parameters: – Disable Timeclock until Enabled  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Dis_tck_u_e,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
3,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
dis_tclk_u_e,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area timeclocks to disable  
4.1.21.  
System Control Commands containing no Parameters: – Disable timeclock until end of day or  
enable issued  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Dis_tck_u_eodoe,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
4,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
dis_tclk_u_eodoe,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area timeclocks to disable  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 19 of 36  
4.1.22.  
catchup  
System Control Commands containing no Parameters: – Re-enable timeclock with complete  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_Name,  
GRAFIK_command, DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset, Length  
0,  
Rnbl_tck_cup,  
Lut_triggers,  
5,  
awt,  
LUT_GRF6_0, rnbl_tclk_catchup,  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area timeclocks to re-enable  
4.1.23.  
event  
System Control Commands containing no Parameters: – Re-enable timeclock and do previous  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Rnbl_tck_doprev,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
6,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
rnbl_tclk_do_prev_evt,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area timeclocks to re-enable  
4.1.24.  
System Control Commands containing no Parameters: Standard re-enable timeclock  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Std_tck_rnbl,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
7,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
std_tclk_rnbl,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area timeclocks to re-enable  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 20 of 36  
4.1.25.  
System Control Commands containing no Parameters: Run script(s)  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Run_script,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
8,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
run_script,  
DA_Lut_List,  
Script_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-63  
Description  
Numbers of scripts to run  
4.1.26.  
System Control Commands containing no Parameters: Toggle system variable value  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Toggle_sys_var,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
9,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
toggle_sys_var_val,  
DA_Lut_List,  
Var_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Numbers of system variables to toggle  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 21 of 36  
4.1.27.  
System Control Commands containing no Parameters: Output temp scene  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name,  
Data_Array_Offset,  
10,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
output_temp_scene,  
DA_Lut_List,  
Op_Tmp_Scene,  
DA_Lut_List_Offset,  
0,  
Length  
1
Output_tmp_scn,  
Lut_triggers,  
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
Zone 0  
1
2
Intensity 0  
Fade 0  
3
Delay 0  
4
5
6
Zone number 1  
Intensity 1  
Fade 1  
7
Delay 1  
..  
..  
60  
61  
62  
63  
Zone 15  
Intensity 15  
Fade 15  
Delay 15  
Note: 1 to 16 temp scenes may be selected by this command. To trigger this command, write the number of temp scenes to output into the Data  
Array specified by Data_Array_Name at Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 22 of 36  
4.1.28.  
System Control Commands containing no Parameters: Select scene in area  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Sel_scn_in_area,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
11,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
sel_scene_in_area,  
DA_Lut_List,  
Sel_Scn_Area,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
2
3
Area 0  
Scene 0  
Area 1  
Scene 1  
..  
..  
30  
31  
Area 15  
Scene 15  
Note: 1 to 16 area scenes may be selected by this command. To trigger this command, write the number of area scene pairs into the Data Array  
specified by Data_Array_Name at Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 23 of 36  
4.1.29.  
System Control Commands containing no Parameters: Timeclock new schedule  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Tck_new_sched,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
12,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
tclk_new_schedule,  
DA_Lut_List,  
Clk_sched,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0
1
2
3
..  
Description  
Area tclk 0  
Schedule 0  
Area tclk 1  
Schedule 1  
..  
60  
61  
62  
63  
Area tclk 30  
Schedule 30  
Area tclk 31  
Schedule 31  
Note: 1 to 32 new schedules may be started by this command. To trigger this command, write the number of area timeclocks into the Data Array  
specified by Data_Array_Name at Data_Array_Offset.  
4.1.30.  
System Control Commands containing no Parameters: Set timeclock  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Set_tck,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
13,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
set_tclk,  
DA_Lut_List,  
Set_tclk,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
2
3
4
5
Hour ( 0-23 )  
Minutes ( 0-59 )  
Month ( 1-12 )  
Day of month ( 1-31 )  
Year ( 0 – 99 )  
Day of week ( 1-7, 1=Sunday )  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 24 of 36  
4.1.31.  
System Control Commands containing no Parameters: Enable wallstation(s)  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Enable_ws,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
14,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
ena_wallstation,  
DA_Lut_List,  
Ctrl_ws_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
..  
Link number ( 0-11 ) of Station ID 0  
Station on link ( 0-31 ) of Station ID 0  
..  
62  
63  
Link number ( 0-11 ) of Station ID 31  
Station on link ( 0-31 ) of Station ID 31  
Note: 1 to 32 station ids may be used to enable wallstations. To trigger the command, write the number of station IDs into the Data Array specified  
by Data_Array_Name at Data_Array_Offset  
4.1.32.  
System Control Commands containing no Parameters: Disable wallstation(s)  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Disable_ws,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
15,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
dis_wallstation,  
DA_Lut_List,  
Ctrl_ws_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
..  
Link number ( 0-11 ) of Station ID 0  
Station on link ( 0-31 ) of Station ID 0  
..  
62  
63  
Link number ( 0-11 ) of Station ID 31  
Station on link ( 0-31 ) of Station ID 31  
Note: 1 to 32 station ids may be used to disable wallstations. To trigger the command, write the number of station IDs into the Data Array specified  
by Data_Array_Name at Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 25 of 36  
4.1.33.  
System Control Commands containing no Parameters: Simulate wallstation(s) switch press  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Ws_sw_press,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
16,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
sim_ws_sw_press,  
DA_Lut_List,  
Sim_sw_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
Link number ( 0-11 )  
Station of link ( 0-31 ) of Switch ID 0  
2
3
4
..  
Switch on station ( 0-31 ) of Switch ID 0  
Station of link ( 0-31 ) of Switch ID 1  
Switch on station ( 0-31 ) of Switch ID 1  
..  
63  
64  
Station of link ( 0-31 ) of Switch ID 31  
Switch on station ( 0-31 ) of Switch ID 31  
Note: 1 to 32 switch ids may be used in a single command. To trigger the command, write the number of switch IDs into the Data Array specified  
by Data_Array_Name at Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 26 of 36  
4.1.34.  
System Control Commands containing no Parameters: Simulate wallstation(s) switch release  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Ws_sw_rls,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
17,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
sim_ws_sw_rls,  
DA_Lut_List,  
Sim_sw_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
Description  
0
1
Link number ( 0-11 )  
Station of link ( 0-31 ) of Switch ID 0  
2
3
4
..  
Switch on station ( 0-31 ) of Switch ID 0  
Station of link ( 0-31 ) of Switch ID 1  
Switch on station ( 0-31 ) of Switch ID 1  
..  
63  
64  
Station of link ( 0-31 ) of Switch ID 31  
Switch on station ( 0-31 ) of Switch ID 31  
Note: 1 to 32 switch ids may be used in a single command. To trigger the command, write the number of switch IDs into the Data Array specified  
by Data_Array_Name at Data_Array_Offset.  
4.1.35.  
System Control Commands containing no Parameters: Stop scene ramp down  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Stop_scn_rmp_dn,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
18,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
stop_scene_ramp_dn,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
Length  
1
DA_Lut_List data setup  
Position from DA_Lut_List_Offset  
0-31  
Description  
Area(s) with scenes to stop ramp down  
Note: After setting up the area numbers to stop scene ramps in the DA_Lut_List Data Array, trigger this command by writing the number of areas  
into the Data Array specified by Data_Array_Name at an offset specified by Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 27 of 36  
4.1.36.  
System Control Commands Containing Parameters: Toggle zone  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Toggle_zone,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
19,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
toggle_zone,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to toggle  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
Fade cycles  
4.1.37.  
System Control Commands Containing Parameters: Fade zone(s) to level  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Fade_to_level,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
20,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
fade_zone,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to fade to level  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
2
Level to fade to ( 0-127 )  
Fade cycles  
Delay cycles  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 28 of 36  
4.1.38.  
System Control Commands Containing Parameters: Ramp zone(s) up  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Rmp_zones_up,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
21,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
ramp_zones_up,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to ramp up  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
Initial rate step size  
Repeat rate step size  
4.1.39.  
System Control Commands Containing Parameters: Ramp zone(s) down  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Rmp_zones_up,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
22,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
ramp_zones_down,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to ramp down  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
Initial rate step size  
Repeat rate step size  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 29 of 36  
4.1.40.  
System Control Commands Containing Parameters: Pommel or pulse zone(s Toggle zone)  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Pulse_zone,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
23,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
pulse_zone,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to pommel or pulse  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
2
3
4
5
Delay1 cycles  
Intensity1 ( 0-127 )  
Fade1 cycles  
Delay2 cycles  
Intensity2 ( 0-127 or 255 )  
Fade2 cycles  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 30 of 36  
4.1.41.  
System Control Commands Containing Parameters: Flash zones aka “Multi level ( Flash or  
Warn or Chase )“  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Flash_zone,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
24,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
flash_zone,  
DA_Lut_List,  
Zone_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Zone_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
Zone(s) to flash  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
2
3
4
5
6
7
Delay1 cycles  
Intensity1 ( 0-127 )  
Fade1 cycles  
Delay2 cycles  
Intensity2 ( 0-127 )  
Fade2 cycles  
Delay2 cycles  
Repeat ( 0-255 )  
4.1.42.  
System Control Commands Containing Parameters: Ramp scene zones up  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Rmp_scn_zns_up,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
25,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
ramp_scene_zones_up,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Area_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-31  
System area numbers  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
2
Unaffected intensity ( 0-128 )  
Initial rate step size  
Repeat rate step size  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 31 of 36  
4.1.43.  
System Control Commands Containing Parameters: Ramp scene zones down  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Rmp_scn_zns_dn,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
26,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
ramp_scene_zones_dn,  
DA_Lut_List,  
Area_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Area_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-31  
System area numbers  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
1
2
Unaffected intensity ( 0-128 )  
Initial rate step size  
Repeat rate step size  
4.1.44.  
times  
System Control Commands Containing Parameters: Select system scene(s) using override  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Sel_scene_oride,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
27,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
sel_scene_override,  
DA_Lut_List,  
Scene_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Scene_pars,  
DA_Lut_Parms_Offset,  
0,  
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-63  
System scene numbers  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
0
1
Description  
Fade cycles  
Delay cycles  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 32 of 36  
4.1.45.  
System Control Commands Containing Parameters: Set system variable value  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Set_sys_var,  
Data_Array_Name,  
Lut_triggers,  
Data_Array_Offset,  
28,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
set_sys_var_val,  
DA_Lut_List,  
Var_list,  
DA_Lut_List_Offset,  
0,  
DA_Lut_Parms,  
Var_pars,  
DA_Lut_Parms_Offset,  
0
Length  
1
DA_Lut_List setup  
Position from DA_Lut_List_Offset  
Description  
0-31  
System variable numbers  
DA_Lut_Parms setup  
Position from DA_Lut_Parms_Offset  
Description  
0
New value  
4.1.46.  
Listening to switch presses and releases: Enabling switch presses and releases reporting  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Ena_sw_lsn,  
Data_Array_Name,  
Sw_lsn_trigger,  
Data_Array_Offset,  
0,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
enable_sw_listen,  
length  
1
Note: To enable the reporting of switch presses and releases, write any value into the Sw_lsn_trigger Data Array at offset specified by  
Data_Array_Offset.  
4.1.47.  
Listening to switch presses and releases: Disabling switch presses and releases reporting  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Dis_sw_lsn,  
Data_Array_Name,  
Sw_lsn_trigger,  
Data_Array_Offset,  
1,  
Function,  
awt,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
disable_sw_listen,  
length  
1
Note: To disable the reporting of switch presses and releases, write any value into the Sw_lsn_trigger Data Array at offset specified by  
Data_Array_Offset.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 33 of 36  
4.1.48.  
Listening to switch presses and releases: Listening to switch presses and releases  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Raw_sw_sts_00,  
Data_Array_Name,  
Raw_sw_sts_00,  
Data_Array_Offset,  
0,  
Function,  
passive,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
raw_sw_status,  
link  
0
Switch press and release status storage Data Array format  
Position from Data_Array_Offset  
Description  
0
1
..  
Station0, Switch0, status  
Station0, Switch1, status  
..  
31  
32  
63  
..  
Station0, Switch31, status  
Station1, Switch0, status  
Station1, Switch31, status  
..  
1022  
1023  
Station31, Switch30, status  
Station31, Switch31, status  
Note: You have to set up a separate Map Descriptor for every link to be monitored for switch presses and releases.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 34 of 36  
4.1.49.  
Active read on startup: Retrieving names  
Warning: Only one (1) active read on startup Map Descriptor may be used.  
The retrieval of area, scene and zone names is done with a single active read on startup (ars ) Map Descriptor. Enter the  
start and end numbers for the names you want to retrieve from the eLumen. The names will be stored sequentially in the  
indicated Data Arrays  
// Client side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Get_Names,  
Function,  
ars,  
Node_Name,  
LUT_GRF6_0,  
GRAFIK_command,  
get_names,  
DA_Area_Names,  
Area_Names,  
DA_Area_Names_Offset,  
0,  
Area_Names_Start,  
0,  
Area_Names_End,  
511,  
DA_Scene_Names_Offset,  
0,  
Scene_Names_Start,  
0,  
Scene_Names_End,  
50,  
DA_Zone_Names,  
Zone_Names,  
DA_Zone_Names_Offset,  
0,  
Zone_Names_Start,  
0,  
Zone_Names_End,  
511,  
Length  
1
Area names storage format  
Position from DA_Area_Names_Offset Description  
0
Area (name_start) name  
40  
80  
Area (name_start+1) name  
Area (name_start+2) name  
..  
40 * name_end  
Area (name_end) name  
Scene names storage format  
Position from DA_Scene_Names_Offset Description  
0
Scene (name_start) name  
40  
80  
Scene (name_start+1) name  
Scene (name_start+2) name  
..  
40 * name_end  
Scene (name_end) name  
Zone names storage format  
Position from DA_Zone_Names_Offset Description  
0
Zone (name_start) name  
40  
80  
Zone (name_start+1) name  
Zone (name_start+2) name  
..  
40 * name_end  
Zone (name_end) name  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 35 of 36  
Appendix A. Data Tables  
Table of Legal Values for Commands to be sent to the eLumen  
pnl_emerg_status  
wallstation_status  
switch_status  
Area_status  
timeclock_status  
zone_intensity  
sys_var_val  
time_now  
astro_times  
date  
run_script  
toggle_sys_var_val  
output_temp_scene  
sel_scene_in_area  
tclk_new_schedule  
set_tclk  
ena_wallstation  
dis_wallstation  
sim_ws_sw_press  
sim_ws_sw_rls  
toggle_zone  
code_rev_level  
bootcode_rev_level  
serial_no  
fade_zone  
ramp_zones_up  
ramp_zones_down  
pulse_zone  
halt_zone  
stop_scene_ramp_up  
stop_scene_ramp_dn  
sel_scene  
flash_zone  
ramp_scene_zones_up  
ramp_scene_zones_dn  
sel_scene_override  
set_sys_var_val  
get_names  
dis_tclk_u_e  
dis_tclk_u_eodoe  
rnbl_tclk_catchup  
rnbl_tclk_do_prev_evt  
std_tclk_rnbl  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 
FS-8700-84_Lutron_eLumen Driver Manual  
Page 36 of 36  
Appendix B. Revision History  
Driver Doc.  
Date  
Resp Format  
Comment  
Ver.  
1.00  
1.00  
Rev.  
0
1
05/10/02  
06/27/02  
Initial version  
Updated with awt Map Descriptor function  
Updated get_names function using one  
ars Map Descriptor  
06/28/02  
1.00  
2
Updated switch status and wallstation  
status mapdesc descriptions. Added  
length column to all mapdesc examples.  
Added stop scene ramp down command.  
Added request panel emergency status  
command.  
08/14/02  
1.00  
3
09/23/02  
12/31/02  
1.01  
1.02  
0
0
03/18/02  
08/20/03  
1.03  
1.03  
0
1
Updated max area number to 511  
Releasing  
DUR0262, removed extra rows in Select  
Scene in Area data setup table.  
Major manual reformat – DUR0479  
Changed document name – DUR0468.  
Updated Description – 0469  
Added RS-485 functionality – DUR0481  
Changed protocol and description name  
to ELUMEN. Some formatting updates.  
DUR0468  
Further changes as sanctioned by DR.  
Connection diagram updated to show  
correct adapter, wire list tidied up. Info  
on RS-485 connection requested from  
DR.  
11/07/03  
1.03  
2
10/20/04 Meg Meg  
11/11/04 Meg Meg  
1.03  
3
1.04  
1.04  
0
1
11/12/04 Meg Meg  
Connection drawings updated according  
to data from customer and comments  
from Mac. Formatting and common  
documentation errors eliminated.  
Releasing  
12/17/04 Meg Meg  
1.04  
1.04  
2
3
1/6/05  
JD  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
 

Dyson Water Dispenser DC29 User Manual
Eclipse Fujitsu Ten GPS Receiver AVN 20D User Manual
Eizo Computer Monitor S2133 User Manual
Electro Voice Speaker EVI 15 User Manual
Fisher Price Motorized Toy Car 78477 User Manual
Frigidaire Microwave Oven FGBM205KB User Manual
Fujioh Ventilation Hood BUF 04J User Manual
Gemini CD Player CDX 1250 User Manual
Gigabyte Computer Hardware GA K8NS User Manual
Gitzo Camcorder Accessories GT1540 User Manual