Faber Ventilation Hood INCA PRO 30 RB User Manual

REMOTE WALL CONTROL INSTALLATION INSTRUCTIONS  
WARNING – To reduce the risk of Þre, electric shock and injury to persons, the Remote Wall Control must be  
installed only with Faber range hood models INCA PRO 30 RB or INCA PRO 38 RB, that are marked to indicate  
suitability with this product. Other models cannot be used  
READ AND SAVE THESE INSTRUCTIONS.  
The Installer must leave these instructions with the homeowner.  
The homeowner must keep these instructions for future reference and for local electrical inspectors’ use.  
WARNING  
Risk of electrical shock. Electrical wiring must be done by qualiÞed personnel in accordance with all applicable codes and standards. Turn  
off the power and lock out the service panel before installing, wiring, or servicing this product. To prevent serious injury from electrical  
shock or damage to electrical components - MAKE SURE POWER IS OFF! This unit must be grounded.  
WARNING  
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:  
a. Installation Work And Electrical Wiring Must Be Done By QualiÞed Person(s) In accordance With All Applicable Codes and Standards,  
Including Fire-Rated Construction.  
b. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden wires.  
MAKE YOUR CUT-OUTS.  
WARNING  
• Cut a level 4 11/32” X 3 5/32” hole in to your desired location.  
• Route the electrical cable from the hood to the wall control location.  
black wiring  
Y/G wiring  
INSTALL THE REMOTE WALL CONTROL  
WARNING – To reduce the risk of Þre and electric shock, do not use this  
control in an insulated wall  
• Remove the back metalic panel of the Remote Wall Control by removing the four  
screws.  
• Insert and Þx a cable with four wires (Brown, Black, Red and Green Ground Wire)  
white wiring  
into the knockout hole of the back metalic panel.  
brown wiring  
• Connect the green ground wire from the cable to the green ground screw.  
• Connect the red wire from the cable to the red Remote Wall Control wire with a  
twist-on wire connector.  
• Connect the brown wire from the cable to the white/black Remote Wall Control  
wire with a twist-on wire connector.  
red wiring  
• Connect the black wire from the cable to the two black Remote Wall Control wires  
with a twist-on wire connector.  
• Replace the back metalic panel.  
The twist on wire connector should be suitable for connecting multiple wires of different sizes  
together.  
• Remove the faceplate from the Remote Wall Control by removing two screws.  
• Position the remote control box in a hole so that both face plate mounting tabs are ßush to the  
Þnished wall surface. Fasten it to a wall stud using four screws (not supplied)  
• Reinstall the control faceplate, ensuring not to pinch the wires.  
CONNECTION OF THE REMOTE WALL CONTROL TO THE RANGEHOOD  
To install the rangehood, please refer to the hood installation instructions.  
• Remove the grease Þlters USING TWO HANDS one to hold the Þlter so that it doesn’t fall on  
cooktop and one to turn the knob by pulling the knob out and turning to the left.  
• Remove the entire bottom of the rangehood by pushing your thumbs into the side holes and  
pulling the sides free from the rangehood.  
 

Ericsson Cell Phone TMX 8810 User Manual
Fender Guitar 011 7602 User Manual
Fender Speaker LTB 12 User Manual
Ferris Industries Lawn Mower 5900633 User Manual
Fisher Paykel Refrigerator RX256DT7X1 User Manual
Fisher Price Baby Toy 77702 User Manual
Fisher Price Motorized Toy Car L6348 User Manual
GE Food Warmer JKD915 User Manual
GE Universal Remote 24962 User Manual
GE Waffle Iron 106582 User Manual