EverFocus Security Camera EQH5102 User Manual

EQH5102 1080p Mini Box Camera  
User’s Manual  
** Lens not included.  
Copyright © EverFocus Electronics Corp,  
Release Date: July, 2012  
 
Safety Notice  
Federal Communication Commission Interference Statement  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates uses and  
can radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the interference by one of the  
following measures:  
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
-
Consult the dealer or an experienced radio/TV technician for help.  
FCC Caution: Any changes or modifications not expressly approved by the party responsible for  
compliance could void the user's authority to operate this equipment.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
ATTENTION! This is a class A product which may cause radio interference in a domestic  
environment; in this case, the user may be urged to take adequate measures.  
This Product is RoHS compliant.  
Your EverFocus product is designed and manufactured with high quality materials and  
components which can be recycled and reused. This symbol means that electrical and  
electronic equipment, at their end-of-life, should be disposed of separately from your  
household waste. Please, dispose of this equipment at your local community waste  
collection/recycling centre. In the European Union there are separate collection systems for  
WEEE  
used electrical and electronic product.  
Please, help us to conserve the environment we live in!  
ii  
 
Contents  
1. INTRODUCTION ........................................................................................ 1  
1.1 PACKING LIST .............................................................................................................. 1  
1.2 FEATURES .................................................................................................................. 1  
2. OVERVIEW ............................................................................................... 2  
3. INSTALLATION .......................................................................................... 2  
3.1 LENS INSTALLATION AND ADJUSTMENT .............................................................................. 2  
3.2 TOP / BOTTOM-MOUNT ............................................................................................... 3  
4. BASIC CONNECTION .................................................................................. 3  
5. CONFIGURATION IN THE OSD MENU.......................................................... 3  
5.1.1 EXPOSURE.............................................................................................................................. 4  
6. SPECIFICATIONS .................................................................................... 10  
7. APPENDIX ............................................................................................. 11  
7.1 OSD MENU STRUCTURE............................................................................................... 11  
iii  
 
EQH5102 1080p Mini Box  
Camera  
1. Introduction  
The EQH5102 is an HDcctv indoor mini box camera. Based on a progressive scan CMOS sensor for  
HD 1080p resolution 100% digital images, it delivers vastly superior video quality compared to  
traditional CCTV images. This superior resolution not only captures more critical evidentiary  
information, but the inherent ability for megapixel video also extends the area of coverage,  
expedites completion of investigations, resolves complaints and reduces both capital and  
operational costs.  
No major upgrade to the IT network is required to deploy this powerful technology; HDcctv  
cameras communicate at digital speeds up to 1.5 Gb/s over existing or new coaxial cable (RG59 or  
other types for longer distances), using industry standard BNC connectors.  
The EQH5102 allows flexible choices of megapixel manual & DC iris control lenses with C / CS  
mount for outstanding coverage in a wide range of demanding surveillance environments while  
delivering stunning HD image quality.  
1.1 Packing List  
Camera body x 1  
Power Pigtail Cable x 1  
User Manual x 1  
Lens Cover x1  
C-mount lens adapter x 1  
1.2 Features  
Real time HDcctv 1080p HD video over coax for superlative image detail  
1/3” 2.1 megapixel Color Progressive CMOS sensor  
CS/C mount, manual and DC iris control for flexible choice of HD Megapixel lenses  
Provides 3D DNR/ DSS to improve image clarity, particularly in low light scenes  
Electronic Lens Shading Compensation to offset diminished light transmission through lens  
periphery for uniform image illumination  
CTB [Contrast Boost] to deliver properly exposed images despite bright light sources, deep  
shadows and/or unbalanced lighting in the same scene  
Supports Digital Zoom/ BLC [Back Light Compensation]/ HSMASK [Highlight Suppression  
Mask]/ Privacy Zones (up to 32)  
DPC [Defect Pixel Correction] Dead pixel compensation for increased clarity and extended  
service life  
SD TV Out for aim and focus using a standard hand held test monitor  
1
 
EQH5102 1080p Mini Box Camera  
2. Overview  
No. Name  
Descriptions  
Connects to a HD device using a 75 Ohm BNC-type  
coaxial cable.  
1
2
3
HDcctv Output  
Use the joystick to configure the settings in the OSD  
menu.  
OSD Menu Joystick  
Screwless Terminal Strip  
Connects to a 12VDC power, RS-485 and MD (Motion  
Detect) source.  
4
5
Power LED  
Glows red then power is present.  
Grounding Stud  
Ensuring a good grounding when used.  
Connects to a SD CVBS monitor for setting image aim and  
focus.  
6
Test-Out  
3. Installation  
3.1 Lens Installation and Adjustment  
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use  
a lens with aperture ratio of F/1.2 or lower. Please refer to the following reference steps.  
CS-Mount Lens:  
1. Remove the cover cap from the camera body.  
2. Install the lens into the camera body.  
3. Adjust the lens using the Focus / Zoom Screws.  
2
 
EQH5102 1080p Mini Box Camera  
If you are using a DC Auto Iris lens:  
1. Remove the cover cap from the camera body.  
2. Install the lens into the camera body.  
3. Connect the DC cable to the DC Auto Iris Lens Connector.  
4. Lock the Focus Screw.  
C-Mount Lens:  
1. Remove the cover cap from the camera body.  
2. Install the lens into the camera body using the supplied C-mount lens adapter.  
3. Adjust the lens using the Focus / Zoom Screws.  
Warning: Installing a C-mount lens without the C-mount lens adapter may damage the  
camera sensor.  
3.2 Top / Bottom-Mount  
You can use a mounting bracket and screw it on the top of the camera body to suspend the  
camera, or on the bottom of the camera body to support the camera.  
4. Basic Connection  
1. Connect the camera to an HD device, such as an HDcctv DVR, to display the image.  
2. Connect the camera to a 12VDC power source using the supplied Power Cable. You can  
optionally use the supplied Power Pigtail Cable or a power adapter to connect the Power Cable  
to the power source. The power LED will be lit in red.  
3. Connect the camera to a CVBS portable monitor for setting image aim and focus before  
mounting the camera.  
5. Configuration in the OSD Menu  
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD  
menu. For details on the OSD menu structure, see OSD Menu Structure in Appendix.  
3
 
EQH5102 1080p Mini Box Camera  
5.1 OSD Menu  
Press the Enter / Confirm button on the Joystick. The Setup Menu in the OSD appears.  
5.1.1 EXPOSURE  
Press the Enter / Confirm button to enter the submenu.  
BRIGHTNESS  
Use the and buttons to increase or decrease the screen brightness from 0 to 20.  
MODE  
Indoor  
Select this mode when the color temperature of the video image is similar to that found in  
indoor environments (around 5100 to 5300°K).  
Outdoor  
Select this mode when the color temperature of the video image is similar to that found in  
outdoor environments (around 3,000°K to 3,200°K)  
LENS  
You can select the type of the lens. Two types are available: Manual and DC. By default, the  
DC type lens is selected.  
4
 
EQH5102 1080p Mini Box Camera  
Shutter  
Use the and buttons to adjust the shutter speed. The options include: 1/25 ~ 1/60000,  
FLK, and AUTO. Any selection other than AUTO and 1/25 will disable the DSS function.  
DSS (Digital Slow Shutter)  
DSS is used to maintain a vivid screen image by automatically boosting low light levels. The  
value is between x2 ~ X4 and OFF.  
AGC (Auto Gain Control)  
The higher the AGC value, the brighter the screen, but the level of noise will also be increased.  
The options include: 0~10.  
5.1.2 COLOR  
Press the Enter / Confirm button to enter the submenu.  
AWB (Auto White Balance)  
This mode can be used to view areas with a color temperature range. Use the and   
buttons to select the AWB options. The options include: AUTO, AUTO EXTN, PRESET, MANUAL  
COLOR TEMP, R-GAIN and B-GAIN.  
AUTO – Around 2500 to 9500°K  
AUTO EXTN (Extension) – Around 2300 to 10800°K  
PRESET – Use a pure white background to preset the white balance value.  
MANUAL COLOR TEMP – Use the and buttons to adjust the speed. The options  
include: LOW, MIDDLE and HIGH  
R-GAIN and B-GAIN –The options include: 0~20.  
CHROMA  
Use the and buttons to increase or decrease the CHROMA from 0 to 20.  
R-OFFSET/B-OFFSET  
Use the and buttons to increase or decrease the Red and Blue offset from 0 to 20.  
5
 
EQH5102 1080p Mini Box Camera  
5.1.3 IMAGE  
Press the Enter / Confirm button to enter the submenu.  
SHARPNESS  
Use the and buttons to increase or decrease the SHARPNESS from 0 to 10.  
MIRROR/FLIP  
Turn it on to reverse/ flip the image.  
DZOOM  
Turn it on to set up the zoom level  
PRIVACY  
Enter the submenu to set up the privacy masks; up to 31 zones can be created:  
ON ZONE NO: Use the and buttons to select the zone from 0 to 31.  
X, Y-POS, SIZ: Enter the submenu to set up the position or size of the privacy mask zone.  
COLOR: Press to select a color for the selected privacy mask zone.  
TRANS: Press to select the transparency of mask zone.  
SHADING  
Turn it on to offset diminished light transmission through lens periphery for uniform image  
6
 
EQH5102 1080p Mini Box Camera  
illumination.  
DAY&NIGHT  
The options include MODE, AGC THRS, DELAY. A submenu can be entered if you select MODE.  
MODE – Use the and buttons to select AUTO, COLOR and B&W. Switches to a B&W  
feed in low light conditions and then switches back to a Color feed in the daytime.  
AGC THRS –Use the and buttons to select the AGC Threshold from 0 to 20.  
DELAY – Set up the delay time in 0,5,10 and 30 seconds for the camera to switch between  
Day and Night.  
HLMASK  
Turn it on to select the level and color of the masking effect.  
CTB (Contrast Boost)  
Turn it on to deliver properly exposed images despite bright light sources, deep shadows  
and/or unbalanced lighting in the same scene.  
GAMMA  
Use the and buttons to increase or decrease the GAMMA from 0.45 to 0.75.  
5.1.4 BLC  
Press the Enter / Confirm button to enter the submenu.  
MODE  
7
 
EQH5102 1080p Mini Box Camera  
Use the and buttons to select OFF and BLC.  
BLC OSD, POS and SIZ  
Select OFF to disable the BLC function, or select ON to enable the BLC function and for further  
setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION”  
sign displayed on the screen. Use the direction buttons to move the area to the desired  
position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on  
the screen. Use the direction buttons to adjust the size for the area.  
5.1.5 3D-DNR  
Press the Enter / Confirm button to enter the submenu.  
Switch to HIGH, MIDDLE, LOW and OFF to enable or disable noise reduction on dynamic  
recordings.  
5.1.6 MOTION  
Press the Enter / Confirm button to enter the submenu.  
8
 
EQH5102 1080p Mini Box Camera  
RESOLUTION  
Use the and buttons to increase or decrease the RESOLUTION level from 0 to 4.  
SENSITIVITY  
Press to set up the sensitivity for the motion detection function.  
WINDOW TRANS  
Press to select the transparency of motion detect zone.  
WINDOW USE, POS and SIZ  
Select OFF to disable this function, or select ON to enable and for further setup. After  
selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign  
displayed on the screen. Use the direction buttons to move the area to the desired position.  
Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen.  
Use the direction buttons to adjust the size for the area.  
5.1.7 SYSTEM  
Press the Enter / Confirm button to enter the submenu.  
DEFECT DET  
Press to select the DPC (Defective Pixel Correction) level of defect detector. Please notice; do  
not use this function without cover the lens. The camera will automatically correct pixel  
defects. Misoperation will cause the abnormal image.  
9
 
EQH5102 1080p Mini Box Camera  
CAM TITLE  
Switch to On and then enter the submenu to set up a camera name displayed on the screen.  
RS-485  
Use the and buttons to select ID, BAUDRATE, PROTOCOL and ID DISPLAY. The default of  
protocol is EVF-1 (EverFocus).  
Version  
Press to display the firmware version of the camera.  
DOUT  
There are 4 options including 1080p 30FPS NTSC, 1080p 25FPS PAL, 720p 60FPS NTSC and  
720p 50FPS PAL  
Language  
Select a language for the OSD text. Options include English, French, German, Simplified  
Chinese, Korean and Japanese.  
6. Specifications  
Camera  
Pickup Device  
Image Pixels  
Resolution  
1/3” Panasonic 2.1 megapixel Color Progressive CMOS sensor  
1920(H) x 1080(V)  
Digital:1080p(30/25), 720p(60/50)  
Color: 0.4 lux, BW: 0.1 lux,  
Sensitivity  
Color DSS: 0.1 lux, BW DSS: 0.025 lux  
Digital(HDcctv Output): BT.1120, HDcctv/HD-SDI: BNC connector  
Analogue(Test Out): NTSC/PAL CVBS(w/o WDR): BNC connector  
More than 50 dB (AGC OFF)  
Video Output  
S/N Ratio  
Lens  
DC/Manual  
AGC  
0-20 steps  
Shutter Speed  
AUTO/MANUAL(1/25(30)~1/60,000sec)  
10  
 
EQH5102 1080p Mini Box Camera  
Digital Slow Shutter(DSS)  
Brightness  
On/Off(x4)  
0-20  
BLC  
On/Off  
Contrast Boost(CTB)  
Day&Night  
On/Off  
Auto/Color/B&W  
Auto/Auto extn/Preset/Manual  
Auto White Balance  
Digital Noise Reduction(DNR) Off/Low/Middle/High  
Mirror  
On/Off  
Flip  
On/Off  
Sharpness  
0 - 10 steps  
On/Off  
Lens Shading Compensation  
Digital Zoom  
Privacy Mask  
Motion Detection  
0 - 96 steps  
32 Zones, Programmable  
On/OffSwith Output, Screwless terminal connector)  
2400~115200> baud, ID 1~255, Protocols: Pelco-D/P, EverFocus  
EVF-1; Screwless terminal connector  
RS - 485  
Language  
English/French/German/Simplified Chinese/Japanese  
12VDC, Screwless terminal connector  
12VDC: 2W max.  
Power Source  
Power Comsumption  
Operating Environment  
Dimensions(L x W x H)  
Weight  
0°C~45°C/32°F~113°F (20%~80% Humidity)  
89 x 46 x 48mm /3.5” x1.8” x1.9”  
0.193kg/0.434lbs  
Certifications  
FCC / CE  
7. Appendix  
7.1 OSD Menu Structure  
The default value is marked with a star “*”.  
No  
Main  
Sub Menu  
Sub Menu / Function  
.
1
EXPOSURE BRIGHTNESS  
1~20 (default=6)  
INDOOR*, OUTDOOR  
MANUAL, DC*  
MODE  
LENS  
11  
 
EQH5102 1080p Mini Box Camera  
AUTO*  
SHUTTER  
MANUAL  
1/25~1/60000  
FLK  
DSS  
OFF, X2, X3, X4*  
0~10 (default=10)  
AUTO*  
AGC  
AUTO extn  
PRESET  
AWB  
MANUAL COLOR TEMP  
R-GAIN  
LOW, MIDDLE, HIGH  
2
3
COLOR  
IMAGE  
0~20  
0~20  
B-GAIN  
CHROMA  
R-OFFSET  
B-OFFSET  
SHARPNESS  
MIRROR  
FLIP  
0~20 (default=7)  
0~20 (default=12)  
0~20 (default=5)  
0~10 (default=6)  
ON, OFF*  
ON, OFF*  
D-ZOOM  
0~96 (default=0)  
OFF*  
ON ZONE NO  
ZONE UP  
X-POS  
0~31  
ON, OFF  
0~60  
PRIVACY  
Y-POS  
0~40  
X-SIZ  
0~60  
Y-SIZ  
0~40  
COLOR  
TRANS  
0~4  
SHADING  
ON*, OFF  
AUTO*  
COLOR  
B&W  
NODE  
DAY&NIGHT  
AGC THRS  
MARGIN  
DELAY  
0~20 (default=10)  
0~20 (default=)  
0, 5*, 10, 30 SEC  
OFF*  
HLMASK  
LEVEL  
0~20 (default=10)  
ON  
COLOR BLK*/WHT/YEL/CYN/GRN/MAG/RED/BLU  
12  
 
EQH5102 1080p Mini Box Camera  
CTB  
ON, OFF*  
GAMMA  
MODE  
0.45*, 0.5, 0.55, 0.65, 0.75  
OFF*, BLC  
BLC OSD  
BLC POS-X  
BLC POS-Y  
BLC SIZ-X  
BLC SIZ-Y  
ON, OFF*  
0~20 (default=7)  
0~20 (default=7)  
0~20 (default=5)  
0~20 (default=5)  
4
5
BLC  
3D-DNR  
HIGH, MIDDLE*, LOW, OFF  
OFF*  
RESOLUTION  
0~4 (default=1)  
0~20 (default=10)  
0~6 (default=3)  
ON, OFF*  
SENSITIVITY  
WINDOW TRANS  
6
MOTION  
WINDOW USE  
ON  
X-POS  
0~60 (default=4)  
0~40 (default=6)  
0~60 (default=15)  
0~40 (default=20)  
000~255 (default=26)  
Y-POS  
X-SIZ  
Y-SIZ  
DEFECT DET  
CAM TITLE  
DPC LEVEL  
OFF*  
STRING SET  
ON  
POSITION  
ID  
1~255 (default=1)  
BAUDRATE 2400, 4800, 9600*, 19200, 38400, 57600, 115200  
PROTOCOL PELCO-D, PELCO-P, EVF-1*  
ID DISPLAY ON, OFF  
RS-485  
7
SYSTEM  
DOUT SCALE  
DOUT  
FULL*, COMP  
720P, 1080P*  
FORMAT  
DOUT FPS  
FREQ  
50, 60 ,25*, 30  
50*, 60 HZ  
CVB  
PAL*, NTSC  
LANGUAGE  
RESET  
English, Simplified Chinese, Japanese, Korean, French, German  
PUSH, PUSHING  
13  
 
EverFocus Electronics Corp.  
EverFocus Taiwan:  
EverFocus Europe - Germany:  
Albert-Einstein-Strasse 1, D-46446  
Emmerich, Germany  
12F, No.79, Sec. 1, Shin-Tai Wu Road,  
Hsi-Chih, Taipei, Taiwan  
TEL: +886 2 2698 2334  
TEL: +49 2822 93940  
FAX: +886 2 2698 2380  
FAX: +49 2822 939495  
EverFocus China - Beijing:  
EverFocus China - Shenzhen:  
4F, No. 2, D4 Building, Wan Yelong  
Industrial Park, Tangtou Road, Shiyan,  
Baoan, Shenzhen, Guangdong 518101, China  
TEL: +86 755 2765 1313  
Room 609, Technology Trade Building,  
Shangdi Information Industry Base,  
Haidian District, Beijing 100085, China  
TEL: +86 10 6297 3336~39  
FAX: +86 10 6297 1423  
FAX: +86 755 2765 0337  
EverFocus USA - California:  
1801 Highland Avenue, Unit A, Duarte, CA 91010,  
USA  
EverFocus USA - New York:  
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA  
TEL: +1 631 436 5070  
TEL: +1 626 844 8888  
FAX: +1 631 436 5027  
FAX: +1 626 844 8838  
EverFocus Japan:  
EverFocus Europe - UK:  
5F, Kinshicho City Building, 2-13-4  
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan  
TEL: +81 3 5625 8188  
Unit 12, Spitfire Business Park,  
Hawker Road, Croydon Surrey, CR0 4WD, UK  
TEL: +44 20 8649 9757 / +44 845 430 9999  
FAX: +44 20 8649 9907  
FAX: +81 3 5625 8189  
EverFocus India:  
Suite 803, Housefin Bhavan, C-21, Bandra Kurla  
Complex, Bandra (East), Mumbai 400051, India  
TEL: +91 22 6128 8700  
FAX: +91 22 6128 8705  
Ihr EverFocus Produkt wurde entwickelt  
und hergestellt mit qualitativ  
hochwertigen Materialien und  
Komponenten, die recycelt und wieder  
verwendet werden können.  
Dieses Symbol bedeutet, dass  
elektrische und elektronische Geräte am  
Ende ihrer Nutzungsdauer vom  
Hausmüll getrennt entsorgt werden  
sollen.  
Your EverFocus product is designed  
and manufactured with high quality  
materials and components which can  
be recycled and reused.  
This symbol means that electrical and  
electronic equipment, at their  
end-of-life, should be disposed of  
separately from your household  
waste.  
Please, dispose of this equipment at  
your local community waste  
collection/recycling centre.  
Bitte entsorgen Sie dieses Gerät bei  
Ihrer örtlichen kommunal
Sammelstelle oder im Recycling Centre.  
Helfen Sie uns bitte, die Umwelt zu  
erhalten, in der wir leben!  
In the European Union there are  
separate collection systems for used  
electrical and electronic product.  
Please, help us to conserve the  
N
 

Echo Trimmer 670 200 User Manual
Eclipse Fujitsu Ten Car Stereo System CD8445 User Manual
Electro Voice Portable Speaker Musicaster II User Manual
Eton Portable Radio Mini300PE User Manual
Eton Radio G4000A User Manual
FEIN Power Tools Grinder WSG 12 70E User Manual
Fisher Price Doll 73397 User Manual
Frymaster Cooktop 17EC User Manual
GE Headphones 28105EE1 User Manual
GE Range 4164D2966P234 User Manual