GE Monogram Refrigerator ZIC360N LH User Manual

Installation  
Instructions  
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com  
ZIC360N RH, ZIC360N LH,  
ZICS360N RH, ZICS360N LH  
Built-In Bottom-Freezer  
Refrigerators  
Design Guide  
With Installation Instructions  
®
Monogram.  
We bring good things to life.  
 
Design Guide  
35"  
Case Width  
THE INSTALLATION SPACE  
DIMENSIONS AND  
CLEARANCES  
The finished cutout width must be 35-1/2".  
35-1/2"  
Finished Width  
* Shipping height. The  
height may  
Wall View  
2-5/16"  
be adjusted from  
83-1/2" to 84-1/2" by  
adjusting leveling legs  
and wheels.  
*84"  
7"  
10"  
Electrical  
Area  
74-1/2" From  
84-1/2" max  
83-1/2" min  
Finished  
Floor to Bottom  
of Electrical  
Product Clearances  
24" Cutout Depth  
5"  
These refrigerators are  
equipped with a 2 position  
door stop. The factory set  
130° door swing can be  
adjusted to 90° if clearance  
to adjacent cabinets or  
walls is restricted.  
Opening  
36"  
5"  
Water Supply  
3 1/2"  
Frame to Frame  
Width  
3 1/2"  
Water And Electrical Locations  
The opening must be prepared with the electrical and  
water supply located as shown.  
130° Door Swing  
90° Door Swing  
25"  
Minimum  
to Wall  
The cutout depth must be 24".  
23-7/8"  
Behind  
Frame  
Designed for industry standard flush installation. The  
refrigerator will project forward, slightly beyond  
adjacent cabinetry, depending on your installation.  
Additional Specifications  
36-3/4"  
• A 115 volt 60Hz., 15 or 20 amp power supply is  
required. An individual properly grounded branch  
circuit or circuit breaker is recommended. Install a  
properly grounded 3-prong electrical receptacle  
recessed into the back wall. Electrical must be  
located on rear wall as shown.  
90°  
130°  
4" Minimum  
to Wall  
Allow 25" minimum clearance for a full 130° door  
Note: GFI (ground fault interrupter) is not  
recommended.  
swing. Allow 15" for pan removal.  
4" minimum clearance is required when door swing is  
adjusted to 90°. If the 90° door stop position is used,  
pan access is maintained, but pan removal is re-  
stricted bottom pans.  
• Water line can enter the opening through the floor  
or back wall. The water line should be 1/4" O.D.  
copper tubing between the cold water line and  
water connection location, long enough to extend  
to the front of the refrigerator. Installation of an  
easily accessible shut off valve in the water line is  
recommended.  
See illustrations pages 4 and 5 to determine door  
swing interaction with adjacent cabinets or  
countertops.  
71-1/2" Finished Width  
ZUG2, ZUGSS2 Unified Grille Panel Kit  
• If you are installing two refrigerators, side by side,  
the installation space must be 71-1/2" wide.  
2-5/16"  
Wall View  
24-3/16"  
7"  
Electrical  
7"  
10"  
10"  
Note: Additional cutout width may be required when side panels  
are used. Add side panel thickness to the finished cutout to  
calculate rough-in width.  
84-1/2" max  
83-1/2" min  
Finished  
24" Cutout  
Depth  
74-1/2" From  
Floor to Bottom  
of Electrical  
Opening  
• The water and electrical locations for each product  
must be located as shown.  
• A separate 115V, 60Hz., 15 or 20 amp power supply  
is recommended for each product.  
5"  
5"  
Water Supply  
26"  
Water Supply  
26"  
3-1/2"  
3-1/2"  
3
 
Design Guide  
Refrigerator  
23-7/8" From  
Rear of  
Refrigerator  
1"  
2"  
3"  
Case  
Trim  
3/4"  
1-3/4"  
1-1/2"  
1-1/4"  
2-3/4"  
2-1/2"  
2-1/4"  
1/2"  
1/4"  
1/4"  
1/2"  
3/4"  
1"  
3/4" Overlay  
Panel  
(Nominal Size)  
Door  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
Top View  
130° DOOR SWING  
(factory setting)  
Scale 1:1  
4
 
Design Guide  
Refrigerator  
Case Trim  
23-7/8"  
From Rear of  
Refrigerator  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
1-1/2"  
Door  
3/4" Overlay  
Panel  
(Nominal Size)  
1/4"  
Top View  
1/2"  
90° DOOR SWING  
(optional setting)  
Scale 1:1  
3/4"  
1"  
1-1/4"  
5
 
Design Guide  
CUSTOMIZATION BASICS:  
Framed Or Overlay Panels, Custom Handles and Accessory Kits  
Models Available  
Overlay panels  
Stainless Steel Wrapped Models:  
ZICS360N RH (right-handed door)  
ZICS360N LH (left-handed door)  
Trimmed models:  
You may also choose to install custom overlay panels  
from your cabinet manufacturer. This design provides a  
seamless appearance which integrates smoothly with  
surrounding cabinetry.  
ZIC360N RH (right-handed door)  
ZIC360N LH (left-handed door)  
Stainless Steel Wrapped Refrigerators  
Stainless Steel wrapped refrigerators have wrapped  
doors and grille panel, beveled edges, and tubular  
stainless steel handles that coordinate with other  
Monogram appliances. These models are shipped  
ready for installation.  
3/4" Overlay Panel  
.10" Thick Spacer Panel  
1/4" Thick Backer Panel  
Standard  
Door Handle  
Trimmed Refrigerators  
Trimmed refrigerators are designed to be customized  
with decorative panels. Field installed custom door and  
grille panels are required.  
Standard supplied handles shown in 3/4" overlay panel position.  
Framed panels  
Door and Drawer Handles  
You may install 1/4" thick custom panels from your  
cabinet manufacturer. The decorative panel slides into  
the factory installed trim. Or, order black, white and  
stainless steel accessory panels from your Monogram  
dealer.  
The standard supplied handles can be adjusted to  
accommodate both framed or overlay panels. Custom  
handles of your choice, supplied by your cabinet maker  
can also be installed. If desired, you may order ZKHCSS2  
Monogram stainless steel tubular handle kit.  
Side Panels  
Side panels must be used whenever the sides of the  
refrigerator will be exposed.  
Standard Door Handle  
Framed Panel  
Standard supplied handles shown in 1/4" panel position.  
Optional Accessory Kits  
Accessory Panels  
• ZKHCSS2: Monogram Tubular Stainless Steel handles  
designed to fit framed or overlay panels.  
White, black and stainless steel accessory panels are  
available from your Monogram dealer. Panels are cut to  
size and ready to install.  
• ZUG2: For side by side installation of two trimmed  
bottom-freezer refrigerators. This kit provides for the  
installation of a unified custom grille panel to span the  
width of two units using a framed or overlay panel.  
• ZUGSS2: For side by side installation of two stainless  
steel wrapped bottom-freezer refrigerators. This kit  
provides a unified stainless steel grille panel to span  
the width of two units.  
ZPBC360–Black, ZPWC360–White,  
ZPSC360–Stainless Steel Panels  
6
 
Design Guide  
1/4" FRAMED PANEL DIMENSIONS  
5/16"  
Trim  
Reveal  
If you choose to install framed panels, they must be  
cut to the dimensions shown. The panels will slide  
into the frame on the door, drawer and grille.  
Door/Drawer  
If the custom panel is less than 1/4" thick and if it fits  
loosely in the door frame, it can be backed up with a  
piece of filler material or foam tape to improve the fit.  
1/4"  
Panel  
IMPORTANT NOTE: Maximum weight for fresh  
food panel is 50 pounds and 30 pounds for freezer  
drawer panel.  
A
Grille Panel  
B
C
Framed Panel Dimensions  
A (Width)  
33-7/8"  
B (Grille Height)  
8-7/8"  
C (FF Height)  
46-1/16"  
D (FZ Height)  
21-7/8"  
1/4" Framed Panel  
Fresh Food  
Panel  
Overlay Panel Dimensions  
A (Width)  
33-7/8"  
32-1/2"  
B (Grille Height)  
C (FF Height)  
46-1/16"  
44-11/16"  
46-5/16"  
D (FZ Height)  
21-7/8"  
20-1/2"  
22"  
1/4" Backer Panel  
0.10" Spacer Panel  
3/4" Overlay Panel  
8-7/8"  
7-5/8"  
9"  
Freezer Drawer  
Panel  
D
34-1/8"  
3/4" OVERLAY PANEL DIMENSIONS  
Overlay Panel  
Door/Drawer  
Overlay  
Panel  
For a more custom appearance, overlay panels may be  
installed on trimmed models. The overlay panel must  
be secured to a 1/4" thick backer panel which slides  
into the trim. A spacer panel 0.10" thick must be placed  
between the overlay and backer panel.  
Spacer Panel  
Backer Panel  
IMPORTANT NOTE: Maximum total weight for  
assembled fresh food panel is 50 pounds and 30  
pounds for freezer drawer panel.  
1/4"  
Backer  
Panel  
.10 Inch  
Spacer  
Assemble the panels with glue and screws.  
• Center the spacer panel on the backer panel, left to  
right and top to bottom. Secure the panels with glue.  
• Center the spacer and backer panel on the overlay  
panel and secure with glue and screws. Screws must be  
countersunk into the backer panel.  
NOTE: Left-to-right offset is not always equal to  
top-to-bottom offset.  
7
 
Design Guide  
ZUG2 GRILLE PANEL DIMENSIONS  
SIDE PANELS  
The ZUG2 unified grille panel kit provides for the  
installation of a framed or overlay grille panel.  
Side panels must be used whenever the sides of the  
refrigerator will be exposed. The 1/4" side panels will  
slip into the side case trim. Order the side panels  
from the cabinet manufacturer.  
A
B
Grille Panel  
24"  
Framed Panel Dimensions  
* Depending on  
installation height.  
A (Width)  
69-7/8"  
B (Height)  
8-7/8"  
1/4" Framed Panel  
Overlay Panel Dimensions  
A (Width)  
69-7/8"  
68-1/2"  
B (Height)  
8-7/8"  
7-5/8"  
9"  
1/4" Backer Panel  
0.10" Spacer Panel  
3/4" Overlay Panel  
*84"  
70-1/8"  
Overlay Panel  
*3" to 4"  
2-9/16"  
Spacer Panel  
Backer Panel  
Assemble the overlay panels in the same manner as  
the door and drawer panels.  
8
 
Installation Instructions  
TOOLS REQUIRED  
MATERIALS REQUIRED  
• Tinsnips to cut banding  
• Stepladder  
• Bucket  
• Level  
• Appliance Hand Truck  
• Tubing cutter  
• 35" long 2x4 for Anti-Tip support  
• Copper water line tubing  
• Water shut-off valve (optional but recommended)  
• Custom panels for fresh food door, freezer drawer  
and grille panel  
• Screws to secure refrigerator to cabinetry.  
• 7/16" open-end wrench  
• #2 Phillips screwdriver  
• Drill and appropriate bits  
• 5/16", 7/16" socket  
• Safety glasses  
FLOORING  
For proper installation, this refrigerator must be  
placed on a level surface of hard material that is at  
the same height as the rest of the flooring. This  
surface should be strong enough to support a fully  
loaded refrigerator, or approximately 700 lbs.  
• 1-1/4" open end wrench  
• Pliers  
HARDWARE SUPPLIED  
• Water filter bypass plug  
• Anti-Tip brackets  
NOTE: Protect the finish of the flooring. Cut a large  
section of the cardboard carton and place under the  
refrigerator where you are working.  
• Special 3M Dual Lock adhesive strips for 1/4" side  
panels  
• 1/4" nut and ferrule  
GROUNDING THE REFRIGERATOR  
IMPORTANT - (Please read carefully)  
have it replaced with a properly grounded 3-prong wall  
outlet.  
FOR PERSONAL SAFETY, THIS APPLIANCE MUST  
BE PROPERLY GROUNDED.  
DO NOT, UNDER ANY  
CIRCUMSTANCES, CUT  
OR REMOVE THE THIRD  
(GROUND) PRONG  
The power cord of this appliance is equipped with a  
three-prong (grounding) plug which mates with a  
standard three-prong (grounding) wall receptacle to  
minimize the possibility of electric shock hazard from  
this appliance.  
FROM THE POWER CORD.  
DO NOT USE AN ADAPTER PLUG TO CONNECT  
THE REFRIGERATOR TO A 2-PRONG OUTLET.  
Have the wall outlet and circuit checked by a quali-  
fied electrician to make sure the outlet is properly  
grounded.  
DO NOT USE AN EXTENSION CORD WITH THIS  
APPLIANCE.  
Where a standard 2-prong wall outlet is encountered,  
it is your personal responsibility and obligation to  
9
 
Installation Instructions  
• Remove the four 7/16"  
bolts securing the straps  
to the skid.  
STEP 1 REMOVE PACKAGING  
CAUTION:  
Refrigerator is much heavier at the  
top than at the bottom – be careful when moving.  
When using a hand truck, handle from side only.  
CAUTION:  
DO  
NOT ATTEMPT TO  
ROLL UNIT OFF SKID.  
PRUDENCE:  
Le réfrigérateur est beaucoup plus  
Remove  
Tie-Downs  
lourd en haut qu'en bas. Il faut être prudent lors des  
déplacements. Si un diable est utilisé, il faut soulever  
le réfrigérateur sur le côté seulement.  
PRUDENCE:  
IL  
NE FAUT PAS ESSAYER  
DE FAIRE ROULER LE  
RÉFRIGÉRATEUR POUR  
L'ENLEVER DE LAY  
PALETTE.  
• Carefully cut banding at the top and bottom, remove  
outer carton.  
• Slide out back corner posts (2).  
• Support blocks on the bottom of the refrigeration  
case must be removed before sliding unit off skid or  
damage will occur. Carefully, tilt refrigerator and  
slide blocks out from beneath, slide unit off skid.  
• Remove toekick. Set aside for final installation.  
• Slide carton off top of cabinet.  
NOTE: IT IS NOT NECESSARY TO LAY CABINET  
DOWN IN ORDER TO REMOVE SKID!  
• The unit is secured to the skid with 4 slotted tie-down  
straps. Remove the four 5/16" bolts from the base  
channels in the tie-downs.  
STEP 2 INSTALL WATER LINE  
• A cold water supply is required for automatic ice-  
maker operation. The water pressure must be be-  
tween 40 and 120 p.s.i.  
• Route 1/4" OD copper tubing between house cold  
water line and the water connection location.  
• Copper tubing should be long enough to extend to  
the front of the refrigerator. Allow enough tubing to  
accommodate bend leading into the water line  
connection.  
Floor  
Copper Tubing  
Compression Nut  
Shut off the main water supply.  
Turn on the nearest faucet long enough to clear the  
Saddle Type  
Shutoff Valve  
line of water.  
• Install a shut-off valve between the icemaker water  
valve and cold water pipe in a basement or cabinet.  
The shut-off valve should be located where it will be  
easily accessible.  
Packing Nut  
NOTE: It is best to install the valve into a vertical water  
pipe. If you install the valve into a horizontal water  
pipe, make the connection at the top or side, to  
avoid drawing off any sediment from the water pipe.  
Outlet Valve  
Ferrule  
(Sleeve)  
• Drill a 1/4" hole in the water pipe.  
NOTE: Saddle type shut-off valves are included in  
many water supply kits. Before purchasing, make sure  
a saddle type valve complies with your local plumbing  
codes.  
• Fasten the shut-off valve to the pipe with pipe clamp.  
• Tighten the clamp screws until the sealing washer  
begins to swell. Do not over tighten.  
• Place a compression nut and ferrule (sleeve) onto the  
end of the tubing and connect it to the shut-off valve.  
Make sure the tubing is fully inserted into the valve  
and ferrule is tightened.  
• Turn on the main water supply and flush debris. Run  
about a quart of water through the tubing into a  
bucket. Shut off water supply at the shut-off valve.  
NOTE: Commonwealth of Massachusetts Plumbing  
Codes 248CMR shall be adhered to. Saddle valves  
are illegal and use is not permitted in Massachusetts.  
Consult with your licensed plumber.  
10  
 
Installation Instructions  
STEP 4 INSTALL ANTI-TIP  
BRACKETS  
STEP 2A WATER LINE  
INSTALLATION WITH A REVERSE  
OSMOSIS SYSTEM  
WARNING:  
ANTI-TIP PRECAUTIONS  
The refrigerator is top-heavy and must be secured to  
prevent the possibility of tipping forward.  
Skip this step when not using an RO System  
If the water supply to the refrigerator is from a  
Reverse Osmosis Water System use the refrigerator’s  
filter bypass plug. Using the refrigerator’s water  
filtration cartridge with the RO filter can result in  
hollow ice cubes.  
ATTENTION:  
Le réfrigérateur est beaucoup plus lourd en haut et il  
faut le maintenir en place pour éviter la possibilité de  
son basculement vers l'avant.  
PRECAUTIONS CONTRE LES  
BASCULEMENTS  
• Cut a 2" x 4" x 35" block and secure the block to  
the mounting brackets provided using #12 or #14  
wood screws.  
Mounting Bracket  
2 x 4 Cut  
To 35" Length  
Filter Bypass Plug  
Installation  
Height  
From Floor  
Wood Screws Mounted into  
Vertical Wood Studs  
STEP 3 INSTALL SIDE PANELS  
• Secure the bracket with wood block to the back wall  
so that it is 84" (or your installation height) from the  
finished floor. See illustration.  
Skip this step when not using side panels  
If you are using 1/4" side panels, they should be  
inserted into the case trim. Fasten the panels to the  
refrigerator with the 3M Dual Lock adhesive strips  
(provided) before setting refrigerator in place.  
Brackets  
Required  
Soffit  
Brackets  
Not Required  
Beneath a  
Soffit  
Block  
Height  
From  
Floor  
to  
Bottom  
of Wood  
Block  
Side View  
• Screws must penetrate at least one inch into vertical  
wall studs.  
• Gently push refrigerator into the opening with  
hands against front corners.  
Important Note: When the refrigerator is installed under a soffit or if  
there is not enough height for this method of security, brackets cannot  
be used. Proceed to step 5 to level the refrigerator and then to step 6 to  
secure refrigerator to cabinets. The refrigerator must be secured to  
prevent tipping.  
11  
 
Installation Instructions  
STEP 6 SECURE REFRIGERATOR  
STEP 5 LEVEL REFRIGERATOR  
TO CABINETRY  
All models have 4-point leveling. The front is sup-  
ported by leveling legs, the rear is supported by  
adjustable wheels. Both are accessible from the front  
of the refrigerator.  
Whenever possible, perform this step for anti-tip  
security, or when anti-tip brackets cannot be used.  
The refrigerator must be secured to prevent tipping.  
• To level the back of the refrigerator, turn the 7/16"  
hex nut located above the front wheels. Turn  
clockwise to raise or counterclockwise to lower the  
refrigerator.  
• Raise the grille panel to access case trim.  
• Drill hole in trim and drive screw through the trim  
into adjacent cabinet.  
• For front leveling, use a 1-1/4" open-end wrench.  
• Adjust height of refrigerator to match installation  
cutout opening 83-1/2 to 84-1/2". The refrigerator  
should be level and plumb with cabinetry.  
• Follow the same procedure on the opposite side.  
Drive Screws  
Through Case Trim and Into  
Adjacent Cabinets  
Hex Nut Adjusts  
Rear Wheels  
Leveling Leg  
12  
 
Installation Instructions  
STEP 7 ADJUST DOOR SWING  
STEP 8 INSTALL GRILLE PANEL  
NOTE: This refrigerator has a 2-position door stop.  
When space does not allow the door to swing open  
fully to 130°, you may change the door swing to a 90°  
opening. Skip this step if door opening is satisfactory  
for your installation situation.  
• Raise the grill panel to stop position.  
Raise  
Grille  
Panel  
Loosen  
Side  
Loosen  
Side  
Trim  
• Lift the grille panel to access the wire cover trim.  
• Remove screws on both sides of the wire cover trim  
and lift off.  
• Use pliers to unscrew door stop and reinstall into  
the 90° position.  
Trim  
Screw  
Screw  
Adjust Nut Below  
Spring to Accommodate  
Panel Weight  
Remove  
Wire Cover  
Trim Screws  
• Loose screws on side trim behind frame. Remove  
bottom trim.  
• Slide panel over the metal baker panel and into the  
trim.  
• If necessary, tap with a wood block until panel slips  
under the top trim piece.  
Pin Location For  
Pin Location  
90° Door  
as Shipped  
Swing  
130° Door Swing  
• Reassemble bottom trim. Tighten screws.  
• Adjust the hinge spring to accommodate the panel  
weight, if necessary.  
• Reinstall the wire cover trim.  
13  
 
Installation Instructions  
Right hand models shown. Use the same instructions for  
left hand models.  
STEP 9 INSTALL FRAMED PANELS  
IF YOU ARE INSTALLING OVERLAY PANELS, GO  
TO STEP 9A.  
Handle  
Trim  
Door Trim  
Refrigerator  
Door  
Use Front Holes  
to Secure Trim  
Standard supplied handle shown  
in 1/4" panel position.  
Use Rear Holes  
to Secure Handle  
Install door and drawer panels:  
• Open door to 90°. Remove the 4 Phillips head screws  
from the door handle.  
• Remove handle. Retain all screws.  
• Remove 4 screws holding trim, lift off trim. Retain  
screws.  
• There are two sets of holes in the handle side trim.  
Replace handle side trim by installing the original  
screws in the FRONT screw holes.  
• Secure the handle to the door using the REAR screw  
holes.  
• Slide framed panel into the door trim.  
• Follow the same procedures to install the drawer panel.  
Custom handles  
If you are using custom handles, the handle must be  
properly secured to the panel before sliding the panel  
into the trim.  
• The cabinet manufacturer will supply the custom  
handle and hardware.  
• Secure the door/drawer trim using both the FRONT  
and REAR screw holes. Discard supplied handle.  
14  
 
Installation Instructions  
Right hand models shown. Use the same instructions for  
left hand models.  
STEP 9A INSTALL OVERLAY PANELS  
Door Trim  
Handle  
Trim  
Refrigerator  
Door  
Move  
Forward  
For 3/4"  
Panel  
Use Front Holes  
to Secure Handle  
Use Rear Holes  
to Secure Trim  
Supplied handle shown in the  
overlay panel position.  
Install door and drawer panels:  
• Open door to 90°. Remove the 4 Phillips head screws  
from the door handle.  
• Remove handle. Retain all screws.  
• Remove 4 screws holding trim, lift off trim. Retain  
screws.  
• There are two sets of holes in the handle side trim.  
Replace handle side trim by installing the original  
screws in the REAR screw holes.  
• Secure the handle to the door using the FRONT screw  
holes.  
• Slide overlay panel into the door trim.  
• Follow the same procedures to install the drawer panel.  
Custom handles  
If you are using custom handles, the handle must be  
properly secured to the panel before sliding the panel  
into the trim.  
• The cabinet manufacturer will supply the custom  
handle and hardware.  
• Secure the door/drawer trim using both the FRONT  
and REAR screw holes. Discard supplied handle.  
15  
 
Installation Instructions  
STEP 12 START ICEMAKER  
STEP 10 CONNECT WATER SUPPLY  
Check to be sure that refrigerator power cord is not  
plugged into the wall outlet.  
Power Switch  
Feeler Arm  
• Flip the switch to I (ON). The icemaker will begin  
operation automatically.  
• Be sure nothing interferes with the sweep of the  
feeler arm.  
• Discard the first full bucket of ice cubes.  
• To turn the icemaker off, set the switch to O (OFF).  
House  
Water Supply  
Refrigerator  
Water Supply  
• Locate and bring copper tubing to the front of the  
cabinet.  
• Turn the water on to flush debris from line. Run  
about a quart of water through tubing into a bucket,  
then shut-off water.  
• Slip a 1/4" nut and ferrule (provided) over both  
ends of the copper tubing. Insert tube into the  
union fitting on the unit and tighten nut to union.  
• Turn on the water to check for leaks.  
STEP 13 INSTALL TOEKICK  
• Locate the supplied toekick (shipped taped to  
the side of the refrigerator). Install with 2 screws  
provided, adjust to desired height and tighten screws.  
• A custom toekick can be installed to match or  
complement the surrounding cabinetry. Use the  
supplied toekick as a template to cut out the notch  
and vent holes.  
Note: Make sure excess tubing length does not  
interfere with drawer closing or toekick installation.  
Supplied Toekick  
1/4" or Thicker Toekick  
STEP 11 CONNECT POWER  
• Connect refrigerator power cord plug to a properly  
grounded receptacle, accessible through the top  
left side of the grille opening.  
Important: The vented toekick must remain unob-  
structed for proper air circulation and refrigerator  
operation.  
Raise  
Grille  
Panel  
Electrical  
Outlet  
Sabbath / Light  
Switch  
• Check to make sure power to refrigerator is on by  
opening refrigerator door to see if interior lights  
are on.  
• The temperature controls are preset at 37°F for the  
fresh food section and 0°F for the freezer.  
• Allow 24 hours to stabilize before making  
adjustments.  
16  
 
Notes  
17  
 
Notes  
18  
 
Notes  
19  
 
Note: While performing installations described in this book,  
safety glasses or goggles should be worn.  
TM  
For Monogram local service in your area, call  
1-800-444-1845.  
Note: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
Pub. No. 49-60136  
Dwg. No. 164D4371P001  
(N.D. 729A) 11/01  
®
Monogram.  
General Electric Company  
Louisville, KY 40225  
75260  
 

Cooper Lighting Indoor Furnishings 1463 User Manual
Craftsman Blower 358799431 User Manual
Craftsman Lawn Mower 107289860 User Manual
Cuisinart Gas Grill CGG 180 User Manual
Delta Electronics Network Card TDV User Manual
Dixon Lawn Mower 27 KOH 968999588 User Manual
Dynex CRT Television DX 60D260A13 User Manual
Elation Professional Work Light Event MH User Manual
GE Dishwasher EDW2020 User Manual
GE Oven JKP30DP User Manual