Chief Manufacturing Indoor Furnishings PAC501 User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
IN-WALL ENCLOSURE  
Spanish Product Description  
German Product Description  
Portuguese Product Description  
Italian Product Description  
Dutch Product Description  
French Product Description  
PAC501  
 
Installation Instructions  
PAC501  
DIMENSIONS  
[657.2]  
2X 25.88  
ELECTRICAL CUTOUT  
[581]  
2X 22.88  
DESIGNED TO FIT A SINGLE GANG  
RACO 590, STEEL CITY CY ½ OR  
SIMILAR STYLE ELECTRICAL BOX  
[30.2]  
[148.6]  
2X 5.85  
2X R1.19  
[50.8]  
2X 2.00  
[304.8]  
2X 12.00  
[17.5]  
2X R.69  
[457.2]  
2X 18.00  
[97.9]  
3.85  
[711.2]  
2X 28.00  
[47.6]  
4X 1.88  
[101.6]  
2X 4.00  
[304.8]  
2X 12.00  
[508]  
20.00  
[458.2]  
18.04  
GROUNDING SCREW CONNECTIONS  
[50.8]  
2X 2.00  
[24.9]  
.98  
MEASUREMENTS IN: [MILLIMETERS]  
INCHES  
[762]  
30.00  
3
 
PAC501  
Installation Instructions  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
4
 
Installation Instructions  
PAC501  
TOOLS REQUIRED FOR INSTALLATION  
3/16"  
PARTS  
Grounding screw and washer  
installed at factory  
Earthing symbol IEC 60418 No. 5019  
affixed adjacent to grounding terminal.  
A (1)  
B (1)  
G (4)  
F (10)  
C (8)  
08 x 1/2"  
M7 x 40mm  
E (1)  
M7  
D (4)  
M7 x 50mm  
5
 
PAC501  
Installation Instructions  
INSTALLATION  
Wood Studs  
WARNING: IMPROPER INSTALLATION CAN RESULT IN  
DEATH OR SERIOUS PERSONAL INJURY! This accessory  
should be installed by qualified personnel.  
Site Preparation  
Locate and Prepare Mounting Site  
1. Identify a suitable wall location for the in-wall enclosure.  
IMPORTANT ! : The PAC-501 is designed for in-wall  
installation spanning a minimum of three wood studs, 16"  
on center. Installation of PAC-501 in 2x4 wall results in  
nearly direct contact with vertical studs and back wall.  
Inadequate space will remain for electrical wires/cables,  
plumbing, ductwork, or insulation. Locate installation  
accordingly.  
(A)  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL WIRES OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surfaces is free  
of electrical wires and cables before cutting, drilling, or  
installing fasteners.  
Figure 1  
Frame Housing  
The exposed portion of the center wood stud must be removed  
and the resulting cavity completely framed with wood. The  
following steps are suggested. The actual procedure is  
dependent upon the specific installation.  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surfaces is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
WARNING: STRUCTURAL FAILURE HAZARD! FAILURE  
TO TAKE ADEQUATE PRECAUTIONS CAN LEAD TO  
DEATH OR SERIOUS INJURY! Ensure removal of center  
stud will not cause unacceptable loss of structural strength.  
Consult a qualified building contractor and applicable building  
codes.  
2. Using a stud sensor, locate and mark studs.  
3. Center and level housing between marked studs.  
1. Remove exposed portion of center wood stud flush with  
upper and lower drywall edges.  
4. Using housing as a template, draw pencil line completely  
around housing. (See Figure 1)  
Support  
Blocks  
5. Cut drywall on outside edge of line and remove.  
Horizontal Framing  
Top View  
Wood  
Screws  
(5 places)  
(Typical for each  
support block)  
Figure 2  
6
 
Installation Instructions  
PAC501  
2. Cut four 8" long support blocks out of 2x4 wood.  
3. Using three #10 x 2-1/2" countersunk wood screws (not  
provided), attach each support block to the studs (See  
Figure 2)  
NOTE: Ensure screws are far enough from block end to  
prevent interference with framing screws installed in  
Step 5.  
(A)  
4. If necessary, cut rectangular hole in horizontal framing to  
accomodate the PAC-501 electrical box.  
5. Attach horizontal framing to each support block with two  
#10 x 2-1/2" countersunk wood screws (not provided).  
(See Figure 2)  
In-Wall Enclosure Installation  
1. Install junction box (B) into the PAC-501 (A) using four  
08 x 1/2" Phillips pan head tap screws (F). (See Figure 3)  
(A)  
Figure 4  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL WIRES OR  
CABLES CAN CAUSE DEATH OR SERIOUS  
PERSONAL INJURY! ALWAYS make certain area behind  
mounting surfaces is free of electrical wires and cables  
before cutting, drilling, or installing fasteners.  
5. Drill four 3/16" diameter pilot holes in studs at side mounting  
holes. (See Figure 5)  
(D) x 4  
6
(F) x 4  
(B)  
(G) x 4  
Figure 3  
2. Connect electrical wiring.  
3. Route audio/visual cables into housing.  
4. Center PAC-501 in opening and insert into opening. Align  
front of box with front face of wall. (See Figure 4)  
x
x 4  
5
Figure 5  
6. Attach the PAC-501 to side studs using four M7 x 50mm  
Allen head connector screws (D) and mounting spacers (G)  
using an M4 Allen head drill bit (E). (See Figure 5)  
NOTE: The PAC-501 has 1/2" total clearance between the two  
studs. The spacers allow side to side adjustment.  
7
 
PAC501  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
Chief Manufacturing, a division of  
Milestone AV Technologies  
+31 (0)40 2668615  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8807-000073 Rev A  
¤2008 Milestone AV Technologies  
10/08  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
 

Black Box Computer Accessories BLACK BOX CAT5 5e 6 LAN Performance Verifier User Manual
Black Decker Planer 7698 User Manual
Blodgett Ventilation Hood VIB3870 1 User Manual
Bosch Appliances Home Security System 0 User Manual
Bose Headphones Acoustic Noise Cancelling Headset User Manual
Briggs Stratton Portable Generator 030242 0 User Manual
Brother Sewing Machine 342Fi User Manual
Canon All in One Printer 6570 User Manual
Canon Printer Accessories ip4200 CISS User Manual
Cisco Systems Network Card 3522 BRI User Manual