Chief Manufacturing Indoor Furnishings FSR Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
SMALL FLAT PANEL STATIC WALL MOUNT  
Model: FSR Series  
Specifications:  
Designed for installation on single wood studs or  
drywall (1/2" minimum thickness); either option  
provides ±1/2" lateral shift.  
Weight capacity of 45 lbs (20 kg) for wood stud or  
drywall installation.  
BEFORE YOU BEGIN  
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed using  
the instructions provided. Failure to read, thoroughly understand, and follow all instructions can result in serious  
personal injury, damage to equipment, or voiding of factory warranty.  
If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing  
at 1-800-582-6480 or 952-894-6280.  
8804-000290  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE 700  
SAVAGE, MINNESOTA 55378 USA  
©2006 Chief Manufacturing  
01/06  
 
Installation Instructions  
Model: FSR Series  
TOOLS REQUIRED FOR INSTALLATION  
PARTS  
Drill  
After unpacking carton, inspect and verify contents (See  
Figure 1). If any listed parts are missing or damaged,  
contact Chief Customer Service at 1-800-582-6480.  
1/8" drill bit (wood stud installation)  
3/8" drill bit (drywall installation)  
Hammer (drywall installation)  
Phillips screwdriver, #2  
NOTE: Other tools may be required depending on your  
Table 1: Parts  
method of installation.  
Item  
10  
Description  
Qty  
2
PLATE, Wall  
20  
ANCHOR, Hollow Wall, #10-24  
WASHER, Flat, Standard Machine Screw, #10  
4
30  
4
40  
SCREW, Phillips Pan Head Sheet Metal,  
#10 x 2-1/2"  
2
(20)  
(10)  
(30)  
(40)  
Figure 1: Parts  
3
 
 
Model: FSR Series  
Installation Instructions  
INSTALL MOUNT TO DRYWALL  
INSTALLATION  
The FSR may be installed on either a single wood stud,  
or drywall (1/2" minimum thickness).  
WARNING: Drywall must be 1/2" minimum thickness.  
Failure to provide adequate structural strength for this  
unit can result in serious personal injury or damage to  
equipment!  
INSTALL MOUNT TO SINGLE WOOD STUD  
1. Determine approximate mounting location, keeping in  
mind the display size.  
1. Determine approximate mounting location, keeping in  
mind the display size.  
2. Use a stud sensor to locate applicable wood stud.  
Mark location with a pencil.  
2. Level plate (10) at desired height and, using plate (10)  
as a template, mark the location of the four anchor  
holes (one in each corner slot).  
3. Level plate (10) at desired height and, using plate (10)  
as a template, mark the location of upper and lower  
pilot holes. Ensure marks are in the center of wood  
stud.  
NOTE: Mount can provide ±1/2" of lateral shift by using  
WARNING: ELECTRICAL SHOCK HAZARD! Drilling  
into electrical wires or cables can cause DEATH or  
SERIOUS PERSONAL INJURY! ALWAYS make  
certain area behind mounting surfaces is free of  
electrical wires and cables before drilling or installing  
mount fasteners.  
mount holes on either side of vertical centerline.  
WARNING: ELECTRICAL SHOCK HAZARD! Drilling  
into electrical wires or cables can cause DEATH or  
SERIOUS PERSONAL INJURY! ALWAYS make  
certain area behind mounting surfaces is free of  
electrical wires and cables before drilling or installing  
mount fasteners.  
3. Drill anchor holes using a 3/8" drill bit. Ensure holes  
are straight and completely through drywall.  
4. Insert anchor (20) into anchor hole and seat with  
gentle tapping from hammer. Anchor barbs should be  
fully engaged in drywall (See Figure 3).  
4. Drill pilot holes using a 1/8" drill bit. Ensure pilot holes  
are straight.  
5. Using Phillips screwdriver, insert screw (40) through  
washer (30), plate (10), and drywall (not shown) and  
install into pilot holes (See Figure 2).  
Drywall  
Pilot  
Holes  
(2 places)  
(30)  
(2 places)  
Anchor barb  
Not collapsed  
Figure 3: Drywall Anchor  
Collapsed  
(40)  
(2 places)  
Wood  
Stud  
5. Using Phillips screwdriver, tighten anchor screw until  
anchor has fully collapsed against back side of  
drywall.  
(10)  
NOTE: Anchor screw will feel tight until anchor begins to  
collapse. Screw will then turn easier for many  
turns. Screw will feel tight when anchor has fully  
collapsed.  
Figure 2: Installation to Single Wood Stud  
6. Repeat steps 4. and 5. for remaining anchors.  
6. Repeat for remaining screw (40).  
7. Tighten both screws (40) securely.  
7. Remove and retain anchor screws from anchors (20).  
NOTE: Anchors (20) may come with small washers which  
may be left on the screw or discarded. These  
small washers do NOT replace washers (30).  
8. Using Phillips screwdriver, insert anchor screws  
through washers (30) and plate (10) and install into  
4
 
   
Installation Instructions  
Model: FSR Series  
collapsed anchors (20). Tighten until secure (See  
Button location for  
100mm x 100mm  
pattern (4 places)  
(20)  
(4 places)  
(30)  
(4 places)  
Button location for  
75mm x 75mm  
pattern (4 places)  
Anchor Screw  
(4 places)  
NOTE: Display not shown for clarity.  
(10)  
Figure 6: Install Display to Plate  
3. Close latching flag by rotating flag counterclockwise  
on plate (10) (See Figure 7).  
Figure 4: Installation to Drywall  
INSTALL DISPLAY TO MOUNT  
NOTE: An optional padlock may be used to secure  
latching flag.  
NOTE: Proper interface must be attached to display. See  
instructions that come with interface assembly.  
1. Open latching flag by rotating flag clockwise on plate  
Latching  
Flag  
(10)  
NOTE: Display not shown for clarity.  
Latching  
Flag  
Figure 7: Close Latching Flag  
(10)  
4. Connect cables to display as required.  
REMOVE DISPLAY FROM MOUNT  
Figure 5: Open Latching Flag  
1. Disconnect all cables from display.  
2. Lift and maneuver display such that all buttons fit into  
button openings on plate (10). Lower display firmly  
into place. Ensure each button has fully seated in its  
button opening (See Figure 6).  
2. Open latching flag by rotating flag clockwise on plate  
3. Lift and maneuver display mounting buttons out of  
button openings.  
NOTE: Mounting buttons are shown in the 100mm x  
100mm pattern. Plate (10) will also accomodate  
a 75mm x 75mm pattern.  
5
 
       
Model: FSR Series  
Installation Instructions  
6
 

Blaupunkt Car Stereo System RCR 126 User Manual
Bogen Car Stereo System FMR User Manual
Bosch Appliances Digital Camera LTC 0610 User Manual
Boston Acoustics Stereo Equalizer PRO60 User Manual
Broan Ventilation Hood RME50000 User Manual
Canon All in One Printer 3478B001AA User Manual
Canon Camera Flash 420 EZ User Manual
Carrier Heat Pump 50EZ User Manual
Casio Calculator CE T100 User Manual
Casio Watch MA0607 EC User Manual