Chamberlain Home Security System RWA310R User Manual

®
Model RWA310R  
Wireless Pedestrian & Vehicle Alert  
Base Station Switches:  
Switch #1:  
Overview  
The Alert uses a Passive Infra-Red sensor to detect  
movement of people and vehicles, while allowing  
small animals to pass through undetected.  
OFF  
ON  
Buzzer Off  
Buzzer On (Default)  
OFF  
ON  
Switch #2:  
1
2
Carton Inventory  
OFF  
ON  
Long Buzz  
Short Buzz (Default)  
Programming Additional PIR Motion Sensors: The  
Base Station can learn the code of up to 3 additional  
PIR Motion Sensors, responding with unique buzzes.  
To program additional PIR Motion Sensors see Step 6.  
Swivel Bushing  
Passive Infra-Red (PIR)  
Motion Sensor  
Base Station  
Rubber Pads  
Clear Memory: Press and hold the Learn Button on  
the Base Station until 3 beeps are heard.  
AC Adapter  
Sun/Rain Shield  
Mounting Plate  
PIR Motion Sensor Assembly  
& Test  
Step 1  
Operation & Features  
Base Station  
Mute/Off  
Button  
Antenna  
Relay Output  
Contacts  
AC Adapter  
Attach PIR Motion Sensor box to mounting plate with  
large silver screw. Tighten screw until PIR Motion  
Sensor stays in place when repositioned.  
Learn Button  
Base Station Switch #1  
Base Station Switch #2  
On/Off: To turn Base Station off hold down the Mute  
Button until it powers down. The Base Station can be  
turned on by pressing the Mute Button.  
Step 2  
Mute: Press and release the Mute Button to put the  
Base Station into Sleep Mode for one hour. After an  
hour it will activate automatically.  
Battery: The AA Alkaline batteries (not provided) in  
the PIR Motion Sensor will last up to 2 years  
depending on use (Lithium batteries recommended  
for colder environments). If Base Station battery  
(optional) is low, it will beep every few minutes.  
Replace with 9-Volt battery (not provided). For peak  
performance inspect batteries annually and replace  
as needed.  
Install 4 AA Alkaline batteries (not provided). (Lithium  
batteries recommended for colder environments.)  
Test light will flash.  
1
 
PIR Motion Sensor Installation  
Troubleshooting  
The PIR Motion Sensor lights up, but the Base  
Station does not respond.  
Step 7  
The PIR Motion Sensor must be programmed to Base  
Station (See Step 6).  
Ensure Base Station is on and is not muted.  
If the green power light is not lit or is flashing, press  
the Mute Button on the top of the Base Station to  
wake it up.  
If the green power is illuminated, look at the two small  
white Base Station switches next to the Learn Button.  
The #1 Dip Switch should be down, towards the  
circuit board. If it is up, the Base Station has been  
muted. If the Base Station signals when you press the  
Learn Button, it is not muted.  
Mount PIR Motion Sensor  
horizontally on solid surface  
500 mm off the ground and within  
400 m of Base Station (rotate  
sensor to access screw holes). Unit  
should be able to swivel as needed. Attach sun/rain  
shield.  
NOTE: Keep PIR Motion Sensor antenna away from  
metal objects. Do not mount PIR Motion Sensor in  
direct sunlight, near moving tree branches, or in the  
path of a sprinkler system.  
The Alert is not getting expected transmission  
range.  
Keep both antennas vertical and keep PIR Motion  
Sensor antenna away from trees and metal objects.  
Ensure Base Station is in clearest possible sight of  
the PIR Motion Sensor. The less objects between the  
devices, the longer the range.  
PIR Motion Sensor is detecting motion only part  
of the time.  
To detect cars, it is best to mount PIR Motion Sensor  
at height of car’s motor and have it between 1-2 m  
from the road. Swivel sensor as needed.  
Vehicle Alert Installation: For cars, the best  
mounting position is about 500 mm high, between  
1-2 m back, and angled to see the back of car after  
passing the sensor.  
The Alert is giving false alarms.  
Check for moving tree branches or insects in sensor  
window. PIR sensor can also be triggered by light  
shining directly in sensor window, such as reflected  
sunlight, or motion in front of a light source.  
It is possible that condensation has built up on the  
sensor. Wipe condensation from PIR Motion Sensor  
with cotton swab. Let it sit inside for a few hours,  
open to the air, without the batteries and it should  
correct itself.  
1-2 m  
500 mm  
Advanced Features  
Check Sensor Switches on PIR Motion Sensor. See  
Switch Settings.  
Base Station beeps every ten minutes.  
The battery in the Base Station is low. Replace with  
9-Volt battery.  
COM (Common)  
Base Station is not very loud.  
N/O (Normally Open)  
An accessory such as a bell, buzzer or light can be  
attached to the relay switch. The relay switch can  
handle up to 24 Vac at 10 amps. The accessory  
device will need a separate power supply.  
-
-
ACCESSORY  
NOTE: The manufacturer is not responsible for any  
radio or TV interference caused by unauthorized  
modifications to this equipment. Changes or  
modifications not expressly approved by the  
manufacturer could void the user’s authority to  
operate the equipment.  
The Base Station has a relay which can activate other  
devices such as a doorbell, buzzer or light. The relay  
switch can handle up to 24 Vac at 10 amps. The  
accessory device will need a separate power supply.  
The accessories can be purchased at any  
electronics store.  
3
 
© 2008, The Chamberlain Group Inc.  
All Rights Reserved  
114A3673  
 

BenQ Cell Phone M555C User Manual
Black Box Outdoor Cart UCCDL18H User Manual
Black Decker Hot Beverage Maker DK35 User Manual
Blomberg Washer 8629 wze40 User Manual
BRK electronic Network Card ADF Adapter User Manual
Broan Ventilation Hood 678 User Manual
Brother Fax Machine MFC J450DW User Manual
Casio Calculator fx 570ES PLUS User Manual
Casio Video Game Keyboard LK200ES1A User Manual
Char Broil Fryer 7101366 User Manual