Printed in Japan 2006/2(CL.K) 284-8050-01
CCD Camera Power Supply Box
4. Mounting Procedure
CAA-188-210
Installation Instructions
4-1. Mounting the CCD Camera Power Supply Box
Mount the CCD camera power supply box in a location such as under a seat using either
the supplied tapping screws (ø4 x 12) or velcro.
1. Precautions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
■ Mounting Using Tapping Screws
■ Mounting Using Velcro
CCD camera
power supply box
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ø4✕12
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
CCD camera
power supply box
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician
for help.
ø4✕12
INFORMATION FOR USERS:.
Velcro
CHANGES OR MODIFICATIONSTO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL
VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
* Thoroughly wipe any dirt from the mounting
surface.
* Remove the separator from the back of the
velcro and apply it to the mounting surface.
2. Package Contents
Fig.3
Fig.4
1. CCD camera power supply box: ·············1 4. Bag of accessories: ················· 1 bag
Clamp: ······················································ 1
Tapping screws: ········································ 4
2. Selector switch: ························ 1 bag
4-2. Mounting the AUTO/MANU Selector Switch
AUTO/MANU selector switch: ··················· 1
■ Mounting the Switch on the Dashboard
Mounting fitting: ········································ 1 5. Bag of accessories: ················· 1 bag
Label: ························································ 1
Connector cable (red): ······························ 1
Connector cable (light green): ·················· 1
Connector cable (black): ··························· 1
Connector cable (red): ······························ 1
Mount the switch on the dashboard as shown in Fig. 6 using the supplied switch mounting
hole (Fig. 5).
3. Bag of accessories: ················· 1 bag
Electro taps:·············································· 2
Velcro: ······················································· 1
Velcro: ······················································· 1
Cosmetic cover (vehicle part)
Prepared ø12 hole
Label
Cosmetic cover (vehicle part)
3. Making Connections
3-1. System Connection Example
AUTO/MANU selector
switch cable
Mounting nut
AUTO/MANU selector switch
<1DIN TV, 2DIN TV>
CAUTION
Upper
White
Selector switch knob
Yellow
Prepared ø12 hole
CCD camera
power supply box
CCD camera
Mount so that notch on AUTO/MANU
selector switch faces downward.
Fig.5
Fig.6
Light green
Black
Red
To reverse gear
signal (12 V)
■ Mounting the Switch Below the Dashboard
GND
Assemble the AUTO/MANU selector switch as shown in Fig. 7 and mount it below the
dashboard. (See Fig. 8.)
To ACC power supply (12 V)
Mounting fitting
For making connections to a TV
or video monitor equipped
with a video input jack
Fig.1
Mounting fitting
Label
Label
Harness
3-2. Connecting the Supplied Cables
Nut
AUTO/MANU selector
switch
Hook up the supplied connector cables as shown in Fig. 2.
MANU
AUTO
MANU
AUTO
Nut
Clamp
Harness
AUTO/MANU selector
switch
Light
green
Black
Clamp
Red
* Secure the switch harness to portion
mounting fitting using the clip.
A
of the
Tapping screws (ø4 x 12)
Fig.7
Fig.8
To reverse gear signal (12 V)
GND
CAUTION
To ACC power supply (12 V)
1. If harnesses will come into contact with the sharp edges of metal plates, or the like, protect
them using grommets or insulation tubes.
Used to provide a 12 V power supply
to an additional device.
FIG.2
2. Before drilling any holes in a vehicle, make sure that there are no electrical wires, brake fluid
pipes, or the like, running behind to surface to be drilled.
3-3. Power Cable Connections
When connection cannot be made to the terminals, use the supplied Electro Tap to make
the connection as illustrated in the diagram.
3. When installation is complete, test the AUTO/MANU selector switch to make sure it works
properly.
As illustrated in the diagram, the intermediate
cable is brought against the stopper and bent
back in the direction of the arrow.
Explanation of label indications
The tip of the cable is
cut at a convenient
• MANU (manual) : The CCD camera image is given output
priority.
length.
Not needed
From the vehicle side
Power cable
Latch
Coupler connected
to another piece of
equipment
From the unit
• AUTO (automatic) : Normally, the TV image is output. The
camera image is output when the
Stopper
transmission is shifted into reverse.
From the unit
Pass the vehicle-side cable through and
bend back in the direction of the arrow.
Power cable
Hook
Vehicle-side wire
Close with pliers until the latch engages.
Unit-side cable
Clarion Co., Ltd.
Vehicle-side cable
|