FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/PARA USO EN
AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST FÖR BILBRUK/ALLEEN VOOR GEBRUIK IN DE AUTO/
ТОЛЬКО ДЛЯ ИСПОЛЬЗОВАНИЯ В АВТОМОБИЛЯХ/DO UŻYCIA TYLKO W SAMOCHODZIE/ΓΙΑ ΧΡΗΣΗ ΜΟΝΟ ΣΕ ΑΥΤΟΚΙΝΗΤΟ
EN
R
MP3 CD Receiver
CDE-130R / CDE-130RM /
CDE-130RR
• OWNER’S MANUAL
• ANVÄNDARHANDLEDNING
Innan du använder utrustningen bör du läsa
igenom denna användarhandledning.
• GEBRUIKERSHANDLEIDING
Lees deze aanwijzingen aandachtig alvorens dit
toestel te gebruiken.
Please read before using this product.
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor
Gebrauch des Gerätes.
• MODE D’EMPLOI
• РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
Прочтите настоящее руководство перед
началом использования оборудования.
• INSTRUKCJA OBSŁUGI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
Prosimy zapoznać siç z tą instrukcją przed
przystąpieniem do użytkowania urządzenia.
• ΕΓΧΕΙΡΙΔΟ ΧΡΗΣΤΗ
• ISTRUZIONI PER L’USO
Si prega di leggere prima di utilizzare il
attrezzatura.
Παρακαλούμε διαβάστε το πριν
χρησιμοποιήσετε τη σνσκενή.
ALPINE ELECTRONICS GmbH
Wilhelm-Wagenfeld-Straße 1-3,
80807 München, Germany
Phone 089-32 42 640
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS OF U.K., LTD.
ALPINE House
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
Fletchamstead Highway,
Coventry CCV4 9TW, U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord II,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
ALPINE ELECTRONICS (BENELUX) GmbH
Leuvensesteenweg 510-B6,
1930 Zaventem, Belgium
Phone 02-725 1315
Phone 01-48638989
Never Attempt the Following
Installation Location
Do not grip or pull out the disc while it is being pulled back into the
player by the automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power is
off.
Make sure this unit will not be installed in a location subjected to:
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
Correct Handling
Do not drop the disc while handling. Hold the disc so you will not
leave fingerprints on the surface. Do not affix tape, paper, or
gummed labels to the disc. Do not write on the disc.
CORRECT
Inserting Discs
Your player accepts only one disc at a time for playback. Do not
attempt to load more than one disc.
Make sure the label side is facing up when you insert the disc.
Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
INCORRECT
CORRECT
New Discs
To prevent the CD from jamming, the LCD is displayed as error if
discs with irregular surfaces are inserted or if discs are inserted
incorrectly. When a new disc is ejected immediately after initial
loading, use your finger to feel around the inside of the centre hole
and outside edge of the disc. If you feel any small bumps or
irregularities, this could inhibit proper loading of the disc. To
remove the bumps, rub the inside edge of the hole and outside edge
of the disc with a ballpoint pen or other such instrument, then insert
the disc again.
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause the
CD player to skip. For routine cleaning, wipe the playing surface
with a clean, soft cloth from the centre of the disc to the outer edge.
If the surface is heavily soiled, dampen a clean, soft cloth in a
solution of mild neutral detergent before cleaning the disc.
Centre Hole
Centre Hole
New Disc
Outside
(Bumps)
Bumps
Disc Accessories
There are various accessories available on the market for protecting
the disc surface and improving sound quality. However, most of
them will influence the thickness and/or diameter of the disc. Using
such accessories can cause the disc to be out of standard
specifications and may create operational problems. We
recommend not using these accessories on discs played in Alpine
CD players.
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use
any special shape discs.
Use of special shape discs may cause damage to the mechanism.
Transparent Sheet
Disc Stabilizer
2-EN
On handling Compact Discs (CD/CD-R/CD-RW)
•
•
•
•
•
•
Do not touch the surface.
Do not expose the disc to direct sunlight.
Do not affix stickers or labels.
Clean the disc when it is dusty.
Make sure that there are no bumps around the disc.
Do not use commercially available disc accessories.
CAUTION
Alpine accepts no responsibility for lost data, etc., even if data, etc.
is lost while using this product.
On Handling USB Memory
•
•
•
To prevent malfunction or damage, note the following points.
Read the USB memory Owner’s Manual thoroughly.
Do not touch the terminals by hand or metal.
Do not subject USB memory to excessive shock.
Do not bend, drop, disassemble, modify or soak in the water.
Avoid usage or storage in the following locations:
Anywhere in the car exposed to direct sunlight or high
temperatures.
Anywhere the possibility of high humidity or corrosive
substances are present.
Fix the USB memory in a location where driver operation will
not be hindered.
Do not leave the disc in the car or the unit for a long time.
Never expose the disc to direct sunlight. Heat and humidity may
damage the CD and you may not be able to play it again.
To customers using CD-R/CD-RW
•
If a CD-R/CD-RW cannot be played back, make sure the last
recording session was closed (finalized).
Finalize the CD-R/CD-RW if necessary, and attempt playback
again.
•
•
•
USB memory may not function correctly at high or low temperature
The USB flash memory supports a maximum of 4 GB per partition.
The unit recognizes only one partition.
Use only certified USB memory. Note that even certified USB
memory, may not function correctly depending on its type or state.
USB memory function is not guaranteed. Use USB memory
according to the terms of agreement.
Depending on the settings of the USB memory type, memory
state or encoding software, the unit may not play back or display
properly.
About media that can be played
Use only compact discs with the label side showing the CD logo
marks below.
•
•
•
•
•
A file that is copy-protected (copyright protection) cannot be
played back.
USB memory may take time to start playback. If there is a
particular file other than audio in the USB memory, it may take
considerable time before the file is played back or searched.
The unit can play back “mp3” file extensions.
Do not add the above extensions to a file other than audio data.
This non-audio data will not be recognised. The resulting playback
may contain noise that can damage speakers and/or amplifiers.
It is recommended to back up important data on a personal computer.
Do not remove the USB device while playback is in progress.
Change SOURCE to something other than USB, then remove
the USB device to prevent possible damage to its memory.
If you use unspecified compact discs, correct performance cannot
be guaranteed.
You can play CD-Rs (CD-Recordables)/CD-RWs (CD-
ReWritables) which have been recorded only on audio devices.
You can also play CD-Rs/CD-RWs containing MP3 formatted
audio files.
•
•
•
Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs on which a recording
failed or a re-recording was attempted, copy-protected CDs
which do not conform to the audio CD industry standard.
Use discs with MP3 files written in a format compatible with this
unit. For details, see “About MP3”.
•
•
•
“MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.”
•
•
•
“Supply of this product only conveys a license for private,
non-commercial use and does not convey a license nor imply
any right to use this product in any commercial (i.e. revenue-
generation) real time broadcasting (terrestrial, satellite, cable
and/or any other media), broadcasting/streaming via internet,
intranets and/or other networks or in other electronic content
distribution systems, such as pay-audio or audio-on-demand
applications. An independent license for such use is required.
ROM data other than audio files contained in a disc will not
produce sound when played back.
Protecting the USB connection terminal
•
Only a USB memory can be connected to the USB connection
terminal on this unit. Correct performance using other USB
products cannot be guaranteed. A USB hub is not supported.
Do not connect a USB memory over 20 mm wide. Also, avoid
connecting USB memory and Front Aux at the same time.
Depending on the connected USB memory device, the unit may
not function or some functions may not be performed.
The audio file format that can be played back on the unit is
MP3.
•
•
•
•
Artist/song name, etc., can be displayed, however characters
may not be correctly displayed.
3-EN
Attaching
Getting Started
1
2
Insert the left side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
Push the right side of the front panel until it locks
firmly into the main unit.
SOURCE/
Rotary encoder
VIEW
•
•
Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Accessory List
•
•
•
•
•
•
•
•
Head unit ............................................................................1
Power cable........................................................................1
Mounting sleeve.................................................................1
Carrying case.....................................................................1
Bracket key.........................................................................2
Rubber Cap ........................................................................1
Bolt Stud ............................................................................1
Owner’s Manual .......................................................... 1 set
Adjusting Volume
Turn the Rotary encoder until the desired sound is
obtained.
Adjusting Volume : 0 ~ 40
Controllable with Remote Control
This unit can be controlled with an optional Alpine
remote control. For details, consult your Alpine dealer.
Point the optional remote control transmitter at the
remote-control sensor.
Turning Power On and Off
Press SOURCE/ to turn on the unit.
•
The first time power is turned on, the volume will start from level 18.
Press and hold SOURCE/ for at least 2 seconds to
turn off the unit.
Detaching and Attaching the Front
Panel
Remote control sensor
Detaching
1
2
Turn off the unit power.
Press
(Release) at the upper right side until the
front panel pops out.
3
Grasp the right side of the front panel and pull it out.
•
The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel). This is not a
malfunction.
•
•
To protect the front panel, place it in the supplied carrying case.
When detaching the front panel, do not apply excessive force as it
may result in malfunction.
4-EN
Presetting Stations Automatically
Radio
1
2
Press BAND/
/
repeatedly until the desired radio
SOURCE/
band is displayed.
BAND/
A.ME
/
Press and hold A.ME for at least 2 seconds.
The frequency on the display continues to change while the
automatic memory is in progress. The radio will
automatically seek and store 6 strong stations in the
selected band. They will be stored into preset buttons 1 to 6
in order of signal strength.
•
If no stations are stored, the radio will return to the original station
you were listening to before the auto memory procedure began.
Preset buttons
(1 through 6)
Tuning to Preset Stations
Listening to Radio
1
2
Press BAND/
/
repeatedly until the desired band
is displayed.
1
2
Press SOURCE/ to select RADIO mode.
Press BAND/ repeatedly until the desired radio
Press any one of the station preset buttons
(1 through 6) that has your desired radio station in
memory.
The display shows the band, preset number and frequency
of the station selected.
/
band is displayed.
FM1
FM2
FM3
MW
LW
FM1
3
Press
Press and hold
station.
or
to tune in the desired station.
or
for at least 0.5 seconds to seek
Presetting Stations Manually
1
2
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish
to store the station.
The selected station is stored.
The display shows the band, preset number and station
frequency memorized.
•
•
A total of 30 stations can be stored in the preset memory (6 stations
for each band; FM1, FM2, FM3, MW and LW).
If you store a station in a preset memory which already has a station,
the current station will be cleared and replaced with the new station.
5-EN
AF (Alternative Frequencies)
Setting
RDS
SOURCE/
1
2
Press and hold SOUND/RDS for at least 2 seconds
BAND/
A.ME
/
to activate the SETUP mode.
/TA
Turn the Rotary encoder to select the AF mode,
and then press Rotary encoder.
3
4
Turn the Rotary encoder to select ON or OFF.
Press and hold SOUND/RDS for at least 2 seconds
to return to normal mode.
VIEW
Preset buttons (1 through 6)
Notes
SOUND/RDS AUDIO/ENTER (ROTARY ENCODER)
•
•
Press VIEW to return to normal mode.
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Setting RDS Reception Mode and
Receiving RDS Stations
Receiving RDS Regional (Local)
Stations
The RDS (Radio Data System) is a radio information system
using the 57 kHz subcarrier of regular FM broadcast. The RDS
allows you to receive a variety of information such as traffic
information, station names, and to automatically re-tune to a
stronger transmitter that is broadcasting the same programme.
1
2
3
Press and hold SOUND/RDS for at least 2 seconds
to activate the SETUP mode.
Turn the Rotary encoder to select the REGIONAL
mode, and then press Rotary encoder.
The RDS digital data include the following:
PI
Programme Identification
Programme Service Name
List of Alternative Frequencies
Traffic Programme
PS
AF
TP
TA
Turn the Rotary encoder to select ON or OFF. In
the OFF mode, the unit automatically keeps
receiving the related local RDS station.
Traffic Announcement
4
Press and hold SOUND/RDS for at least 2 seconds
to return to normal mode.
EON
Enhanced Other Networks
Notes
•
•
Press VIEW to return to normal mode.
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Recalling Preset RDS Stations
1
Select the band, and then press any one of the
station preset buttons (1 through 6) that has
your desired radio station in memory.
The display shows the band, preset number and frequency of the
station selected.
PI SEEK Setting
1
2
Press and hold SOUND/RDS for at least 2 seconds
to activate the SETUP mode.
2
3
If the preset station’s signal is weak:
The unit automatically searches and tunes to a stronger station
in the AF (Alternative Frequencies) list.
Turn the Rotary encoder to select the PI SEEK
mode, and then press Rotary encoder.
If the preset station and the stations in the AF list
cannot be received:
When the PI SEEK setting is on (refer to “PI SEEK Setting” on
page 6), the unit searches again for a station in the PI
(Programme Identification) list.
3
4
Turn the Rotary encoder to select ON or OFF.
Press and hold SOUND/RDS for at least 2 seconds
to return to normal mode.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
number disappears.
If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button to
tune in a Regional station in other district.
Notes
•
•
Press VIEW to return to normal mode.
If no operation is performed for 60 seconds, the unit will return to
normal mode automatically.
Note
•
For presetting the RDS stations, refer to the Radio Operation
section. The RDS stations can be preset in the FM1, FM2 and FM3
bands only.
6-EN
Receiving Traffic Information
Displaying Radio Text
Text messages from a radio station can be displayed.
1
2
Press and hold
“TA” indicator lights up.
for at least 2 seconds so that the
1
Press VIEW while receiving FM in the radio mode to
select the Radio Text display.
Press
or
to select your desired traffic
The display will change every time the button is pressed.
information station.
When a traffic information station is tuned in, the “TP” indicator
lights up.
Traffic information is heard only when it is being broadcast. If
traffic information is not being broadcast, the unit is set in the
standby mode. When a traffic information broadcast begins, the
unit automatically receives it and the display shows “TRF-INFO”
for 5 seconds.
If there is PS (Programme Service Name):
PS (Programme Service Name)*
(Programme Service Name)
RADIO TEXT
PS
* If VIEW is pressed and held for at least 2 seconds while
displaying PS in the radio mode, frequency will be
displayed for 5 seconds.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
If there is no PS (Programme Service Name):
FREQUENCY
RADIO TEXT
FREQUENCY
Notes
The display shows “WAITING“ for a few seconds, then starts
showing the text message. If the text message is more than 8
characters, it will scroll.
•
•
•
If you do not want to listen to the traffic information being received,
lightly press BAND/ /A.ME to skip that traffic information
message. The TA mode will remain in the ON position to receive the
next traffic information message.
If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is
received next time, the volume level will be automatically adjusted to
the level memorized.
/
Note
•
If there is no receivable text message or the unit cannot receive a text
message properly, the display shows “NO TEXT”.
In the TA mode, the SEEK tuning selects only the TP stations.
Receiving Traffic Information
While Playing CD or Radio
1
2
Press and hold
“TA” indicator lights up.
for at least 2 seconds so that the
Press
or
to select a traffic information
station if necessary.
When a traffic information broadcast starts, the unit automatically
mutes the CD player or the regular FM broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the traffic
information broadcast began.
When traffic information stations cannot be received:
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
Note
•
The receiver is equipped with the EON (Enhanced Other Networks)
function in order to keep track of additional alternate frequencies to
the AF list. The “EON” indicator lights up while an RDS EON
station is being received. If the station being received does not
broadcast the traffic information, the receiver automatically tunes in
the related station that broadcasts the traffic information when it
occurs.
3
Press and hold
deactivate the Traffic Information mode.
for at least 2 seconds to
The “TA” indicator switches off.
7-EN
3
Press
or
to select the desired track (file).
Returning to the beginning of the current track (file):
CD/MP3
Press
.
Fast backward:
Press and hold
.
SOURCE/
Advancing to the beginning of the next track (file):
BAND/
/
Press
.
Fast forward:
Press and hold
.
4
To pause playback, press BAND/
/
.
Pressing BAND/ again will resume playback.
/
5
•
To eject the disc, press
.
6(RPT)
4(M.I.X.)
5(SCAN)
Do not remove a CD during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
•
•
•
•
The “
DISC IN” indicator lights up when a disc is inserted.
Three-inch (8 cm) CDs cannot be used.
The CD-player can play disc containing audio data and MP3 data.
The track display for MP3 data playback is the file numbers recorded
on the disc.
Playback
•
The playback time may not be correctly displayed when a VBR
(Variable Bit Rate) recorded file is played back.
1
Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically, and the
MP3 Play Display
The folder number and file number will be displayed as described
below.
“
DISC IN” indicator lights up .
003–002
Folder number File number
When a disc is already inserted, press SOURCE/ to
switch to the DISC mode.
display
display
The mode will change every time the button is pressed.
•
Press VIEW to switch the display. See “Displaying the Text” for
1
2
information about display switching.
RADIO
CD*
USB*
AUX
RADIO
*1 Displayed only when a disc has been inserted.
*2 Displayed only when USB memory is connected.
Repeat Play
2
While playing back MP3, press
the desired folder.
or
to select
Press 6(RPT) to repeatedly play back the current track.
The “
RPT” indicator lights up, and the track (file) will be
played repeatedly.
Press 6(RPT) again to cancel.
Folder Repeat Play (MP3)
Press and hold 6(RPT) for at least 2 seconds.
The “
FOLDER” and “
RPT” indicators appear in the
display, and only files in the current folder are repeatedly played
back.
Press and hold 6(RPT) again to cancel.
8-EN
M.I.X. (Random Play)
About MP3
Press 4(M.I.X.) in the play or pause mode.
The “
M.I.X.” indicator lights up, and the tracks (files) on the
CAUTION
disc will be played back in random sequence.
Except for private use, duplicating audio data (including MP3
data) or distributing, transferring, or copying it, whether for free
or for a fee, without permission of the copyright holder is strictly
prohibited by the Copyright Act and by international treaty.
Press 4(M.I.X.) again to cancel.
Folder M.I.X. (Random Play) (MP3)
What is MP3?
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a
compression standard prescribed by the ISO, the International
Standardization Organization and MPEG which is a joint activity
institution of the IEC.
Press and hold 4(M.I.X.) for at least 2 seconds.
The “
FOLDER” and “
M.I.X.” indicators appear in the
display, and all files in the current folder are played back in
random sequence.
MP3 files contain compressed audio data. MP3 encoding is
capable of compressing audio data at extremely high ratios,
reducing the size of music files to as much as one-tenth their
original size. This is achieved while still maintaining near CD
quality. The MP3 format realises such high compression ratios by
eliminating the sounds that are either inaudible to the human ear
or masked by other sounds.
Press and hold 4(M.I.X.) again to cancel.
Scanning Programs
Press 5(SCAN) to activate the scan mode.
The first 10 seconds of each track (file) will be played back in
succession.
Method for creating MP3 files
Audio data are compressed using software with MP3 codec. For
details on creating MP3 files, refer to the user’s manual for that
software.
Press 5(SCAN) again to cancel.
MP3 files that are playable on this device have the file extension
“mp3”. Files with no extension cannot be played back.
Folder Scanning Programs (MP3)
Supported playback sampling rates and bit rates
Press and hold 5(SCAN) for at least 2 seconds.
From the next folder, the first 10 seconds of the first file in each
folder is played back in sequence.
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Press and hold 5(SCAN) again to cancel.
Bit rates:
8 - 320 kbps
This device may not play back correctly depending on sampling
rates.
ID3 tags
This device supports ID3 tag.
If tag data is in an MP3 file, this device can display the title (track
title), artist name, and album name ID3 tag data.
This device can only display up to 64 characters. (Unicoded file
and folder names are up to 32 characters.)
For non-supported characters and symbols an asterisk is
displayed.
If information contains characters other than ID3 tag information,
the audio file may not be played back.
The tag information may not be correctly displayed, depending
on the contents.
Producing MP3 discs
MP3 files are prepared, then written to a CD-R or
CD-RW using CD-R writing software. A disc can hold up to 512
files/folders (including Root Folders), and the maximum number
of folders is 255.
Playback may not be performed if a disc exceeds the limitations
described above.
Media supported
The media that this device can play back are CD-ROMs, CD-Rs,
and CD-RWs.
Corresponding File Systems
This device supports discs formatted with ISO9660 Level 1 or
Level 2.
Under the ISO9660 standard, there are some restrictions to
remember.
9-EN
Song information such as track titles, artist names, album names,
etc., written into MP3 files.
The maximum nested folder depth is 8 (including the root
directory). The number of characters for a folder/file name is
limited.
Root folder
Valid characters for folder/file names are letters A-Z, a-z,
numbers 0-9 and symbols.
The root folder (or root directory) is found at the top of the file
system. The root folder contains all folders and files. It is created
automatically for all burned discs.
This device also can play back discs in Joliet, Romeo, etc., and
other standards that conform to ISO9660. However, sometimes
the file names, folder names, etc., are not displayed correctly.
Formats supported
This device supports Multi-Session.
This device cannot correctly play back discs recorded with Track
At Once or packet writing.
Apple HFS, UDF 1.50, Mixed Mode CD and Enhanced CD (CD-
Extra) are not supported.
Order of files
Files are played back in the order that the writing software writes
them to the disc. Therefore, the playback order may not be what
is expected. Verify the writing order in the software’s
documentation. The playback order of the folders and files is as
follows.
Root folder
Folder
MP3 File
* The folder No./ folder Name will not be displayed if no file is
contained in the folder.
Terminology
Bit rate
This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger
the files.
Sampling rate
This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1 kHz,
so the sound is sampled (recorded) 44,100 times per second. The
higher the sampling rate, the higher the sound quality, but also the
larger the volume of data.
Encoding
Converting music CDs, WAVE (AIFF) files, and other sound files
into the specified audio compression format.
Tag
10-EN
Equalizer Presets (Factory’s EQ)
Sound Setting
6 typical equalizer settings are preset at the factory for a variety of
musical source material.
Rotary encoder (AUDIO)
Press SOUND repeatedly until the desired Factory’s EQ
type is displayed.
With each press of the button, the equalizer mode will display the
selected equalizer characteristic.
FLAT(OFF)
FLAT(OFF)
ROCK
POP
JAZZ
VOCAL
CLUB
SOUND
Adjusting Bass Level/Treble Level/
Balance (Between Left and Right)/
Fader (Between Front and Rear)
1
Press Rotary encoder (AUDIO) repeatedly to
choose the desired mode.
Each press changes the mode as follows:
BASS
TREBLE
BALANCE
FADER
Return to
normal mode
Bass: -12 ~ +12dB
Treble: -12 ~ +12dB
Balance : L15 ~ R15
Fader : R15 ~ F15
•
If no operation is performed for 5 seconds after selecting the BASS,
TREBLE, BALANCE or FADER mode, the unit automatically returns
to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
11-EN
Using the Front AUX Input
Terminal
Other Functions
Connect a portable music player, etc. by simply connecting it to the
input on the front panel. An optional adapter cable is required (standard
RCA to 3.5ø mini-phono plug or 3.5ø to 3.5ø mini phono plug).
SOURCE/
Press SOURCE/ , and select the AUX mode to listen to
the portable device.
1
2
RADIO
CD*
USB*
AUX
RADIO
*1 Displayed only when a disc has been inserted.
VIEW
3(SCROLL)
*2 Displayed only when USB memory is connected.
Portable player, etc.
Main unit
Displaying the Text
Text information, such as the disc name and the track name, will be
displayed if playing a CD text compatible disc. It is also possible to
display the folder name, the file name and the tag, etc., while playing
MP3 files.
Press VIEW.
The display will change every time the button is pressed.
or
•
To scroll text, press 3(SCROLL).
The display in Radio mode:
If there is PS (Programme Service Name)
Optional adapter cable (RCA pin
plugs [red, white] 3.5ø miniplugs)
or (3.5ø miniplugs)
1
PS (Programme Service Name)*
RADIO TEXT
PS (Programme Service Name)
If there is no PS (Programme Service Name)
FREQUENCY
RADIO TEXT
FREQUENCY
The display in CD mode:
2
TRACK NO./ELAPSED TIME
TEXT (TRACK NAME)*
TEXT (DISC NAME)*
2
TRACK NO./ELAPSED TIME
The display in MP3 mode:
FOLDER NO./FILE NO.
FILE NAME ALBUM NAME*
FOLDER NO./FILE NO.
ELAPSED TIME
FOLDER NAME
3
3
SONG NAME* /ARTIST
3
NAME*
1
* If VIEW is pressed and held for at least 2 seconds in the PS display
mode, frequency will be displayed for 5 seconds.
* Displayed during playback of a disc with CD text.
* ID3 tag
2
3
If an MP3 file contains ID3 tag information, the ID3 tag information
is displayed (e.g., song name, artist name, and album name). All
other tag data is ignored.
About “Text”
Text:
Text compatible CDs contain text information such as the disc
name and track name. Such text information is referred to as
“text.”
•
•
•
Some characters may not be displayed correctly with this device,
depending on the character type.
“NO TEXT” is displayed if text information cannot be displayed on
this unit.
The text or tag information may not be correctly displayed,
depending on the contents.
12-EN
USB Memory Connection
(Optional)
USB memory (Optional)
Connect USB memory
SOURCE/
BAND/
/
1
2
Open the cover of the USB connection terminal.
Connect the USB memory directly to the USB
connection terminal.
This unit
USB Connection Terminal
USB memory
(Sold Separately)
Controlling USB memory
(Optional)
A USB memory device may be connected to this unit. With USB
memory connected, playback of files on the device is controlled from
this unit.
Remove USB memory
•
The controls on this unit for USB memory operation are operative
only when a USB memory is connected.
1
Carefully pull out the USB memory from the USB
connection terminal.
Playing MP3 Files with the USB
memory (Optional)
2
Close the cover of the USB connection terminal.
•
Change to a source other than the USB memory mode, then remove
the USB memory. If the USB memory is removed in the USB memory
mode, data may be damaged.
When removing USB memory, pull it out straight.
If sound is not output or USB memory is not recognised even when
USB memory is connected, remove USB memory once, then connect
it again.
After removing the USB memory, close the cover of the USB
connection terminal to prevent dust or foreign objects from entering
and causing a malfunction.
If you connect a USB memory containing MP3, you can play these files
on this unit.
•
•
1
Press SOURCE/ to switch to the USB AUDIO
mode.
•
The mode will change every time the button is pressed.
1
2
RADIO
CD*
USB*
AUX
RADIO
*1 Displayed only when a disc has been inserted.
*2 Displayed only when USB memory is connected.
About MP3 File of USB Memory
2
To pause playback, press BAND/
/
.
Pressing BAND/ again will resume the playback.
/
Playing back MP3
•
The root folder is displayed as “ROOT” in the Folder Name Search
mode.
This unit plays back files on a USB memory device with the same
controls and modes as playback of CDs containing MP3. For details,
refer to “CD/MP3”.
Before disconnecting USB memory, be sure to change to another
source or set to pause.
The playback time may not be correctly displayed when a VBR
(Variable Bit Rate) recorded file is played back.
MP3 files are prepared, then stored to a USB memory. This unit
can recognise at least 999 folders (including root folder) and 255
files per folder stored in USB memory. Playback may not be
performed if a USB memory exceeds the limitations described
above.
•
Do not make a file's playback time more than 1,000 minutes.
•
•
Media supported
This device can play back USB memory media.
Corresponding File Systems
This device supports FAT 12/16/32 for USB memory device.
13-EN
CD
Information
CD Player not functioning.
Out of operating temperature range +70°C (+158°F) for CD.
- Allow the vehicle’s interior (or trunk) temperature to cool.
•
In Case of Difficulty
CD playback sound is wavering.
•
Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about 1
hour).
If you encounter a problem, please turn the power off, then on again. If
the unit is still not functioning normally, please review the items in the
following checklist. This guide will help you isolate the problem if the
unit is at fault. Otherwise, make sure the rest of your system is properly
connected or consult your authorized Alpine dealer.
CD insertion not possible.
•
A CD is already in the CD player.
- Eject the CD and remove it.
Basic
•
The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
No function or display.
Vehicle’s ignition is off.
•
- If connected following instructions, the unit will not operate
with the vehicle’s ignition off.
Unable to fast forward or backward the CD.
•
The CD has been damaged.
•
•
Improper power lead (Red) and battery lead (Yellow) connections.
- Check power lead and battery lead connections.
Blown fuse.
- Check the fuse of the unit; replace with the proper value if
necessary.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
•
•
•
•
Improper mounting of the unit.
- Securely re-mount the unit.
The disc is very dirty.
- Clean the disc.
The disc has scratches.
- Change the disc.
The pick-up lens is dirty.
- Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
Radio
Unable to receive stations.
•
No antenna or open connection in cable.
- Make sure the antenna is properly connected; replace the
antenna or cable if necessary.
Unable to tune stations in the seek mode.
•
If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
CD playback sound skips without vibration.
•
The disc is dirty or scratched.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace the
antenna with a new one.
- Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
Mechanical error.
- Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest Alpine dealer.
•
•
Broadcast is noisy.
•
The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
The antenna is poorly grounded.
- Make sure the antenna is grounded properly at its mounting
location.
CD-R/CD-RW playback not possible.
•
Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
•
MP3
MP3 is not played back.
•
Writing error occurred. The MP3 format is not compatible.
- Make sure the MP3 has been written in a supported format.
Refer to “About MP3”, then rewrite in the format supported by
this device.
14-EN
Indication for CD Player
Indication for USB memory
•
•
The disc is dirty or upside down.
•
•
No song (file) is stored in the USB memory.
- Press the
button and eject the CD.
- Connect the USB memory device after storing songs (files).
A USB device that is not supported by the unit is connected.
- Connect a USB device that is supported by the unit.
If not ejecting, consult your Alpine dealer.
The disc has scratches.
- Press the
If not ejecting, consult your Alpine dealer.
button and eject the CD.
•
Abnormal current is run to the USB connector device (an error
message may be displayed if the USB device that is not
compatible with the unit is connected).
USB memory is a malfunction or it is shorted.
- Disconnect the USB memory device and turn off the power
and turn on Connect another USB memory.
•
•
Mechanism error.
- Consult your Alpine dealer.
•
•
Communication error.
- Turn the ignition key off, and then set to ON again.
A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit.
A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit.
15-EN
GENERAL
Specifications
Power Requirement
12 V DC (11-16 V allowable),
Test voltage 14.4 V, Negative
ground
FM TUNER SECTION
Tuning Range
87.5-108.0 MHz
0.7 µV
Current Consumption
Maximum Power Output
Power Output
Less than 2.1 A (CD mode;
0.5 W × 4)
Mono Usable Sensitivity
Alternate Channel Selectivity
Signal-to-Noise Ratio
Stereo Separation
80 dB
50 W × 4 (at 1 kHz)
volume control maximum
18 W × 4
(1 kHz, 1 %, 4 ohms)
4-8 ohms
65 dB
35 dB
Capture Ratio
2.0 dB
Speaker Impedance
Pre-Output Voltage
Pre-Output Impedance
Dimensions (W × H × D)
Weight
MW TUNER SECTION
2 V (CD mode, 1 kHz, 0dB)
200 ohms
Tuning Range
531-1,602 kHz
25.1 µV/28 dB
Sensitivity (IEC Standard)
178 × 50 × 160 mm
1.2 kg
LW TUNER SECTION
Tuning Range
153-281 kHz
•
Due to continuous product improvement, specifications and design
are subject to change without notice.
Sensitivity (IEC Standard)
31.6 µV/30 dB
CD PLAYER SECTION
Sampling Range
DA Converter
Pick-up Type
8 times oversampling
1 bit DAC System
3-beam Photo Detector Pick
Up
Light Source
Semiconductor laser
790 nm
Wave length
Laser Power
CLASS I
Frequency Response
Signal-to-Noise Ratio
Total Harmonic Distortion
Wow & Flutter
20-20,000 Hz (±1 dB)
96 dB
0.01% (at 1 kHz)
Below measurable limits
85 dB
Channel Separation
USB SECTION
USB requirements
1.1/2.0 Full Speed
Maximum Supply Compatibility 500 mA
Front AUX input
Input Impedance
Allowable external input
Connector
10 kohms
2.0 V
3.5 mm ϕ Stereo mini-pin
16-EN
Installation and Connections
Before installing or connecting the unit, please read the
following and “Operating Instructions” of this manual
thoroughly for proper use.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
Warning
EXPERTS.
MAKE THE CORRECT CONNECTIONS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
Failure to make the proper connections may result in fire or product
damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
DO NOT ALLOW CABLES TO BECOME ENTANGLED
IN SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to
prevent obstructions when driving. Cables or wiring that obstruct or
hang up on places such as the steering wheel, shift lever, brake
pedals, etc. can be extremely hazardous.
Route the cables and wiring away from moving parts (like the seat
rails) or sharp or pointed edges. This will prevent crimping and
damage to the wiring. If wiring passes through a hole in metal, use
a rubber grommet to prevent the wire’s insulation from being cut by
the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit may
result in product failure.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
When drilling holes in the chassis for installation, take precautions
so as not to contact, damage or obstruct pipes, fuel lines, tanks or
electrical wiring. Failure to take such precautions may result in fire.
Precautions
•
•
•
Be sure to disconnect the cable from the (–) battery post before
installing your CDE-130R/CDE-130RM/CDE-130RR. This will
reduce any chance of damage to the unit in case of a short-circuit.
Be sure to connect the colour coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle’s electrical system.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could disable
control of the vehicle and cause fire etc.
When making connections to the vehicle’s electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for this
unit. When connecting the CDE-130R/CDE-130RM/CDE-130RR
to the fuse box, make sure the fuse for the intended circuit of the
CDE-130R/CDE-130RM/CDE-130RR has the appropriate
amperage. Failure to do so may result in damage to the unit and/or
the vehicle. When in doubt, consult your Alpine dealer.
The CDE-130R/CDE-130RM/CDE-130RR uses female RCA-
type jacks for connection to other units (e.g. amplifier) having
RCA connectors. You may need an adaptor to connect other
units. If so, please contact your authorized Alpine dealer for
assistance.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT
OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
•
•
DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR SHIFT LEVER.
Be sure to connect the speaker (–) leads to the speaker (–)
terminal. Never connect left and right channel speaker cables to
each other or to the vehicle body.
IMPORTANT
SERIAL NUMBER:
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number or the
engraved serial number is located on the top of the unit.
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
17-EN
Screw
2
Installation
Hex Nut (M5)
Caution
*2
Do not block the unit's heat sink, thus preventing air circulation. If
blocked, heat will accumulate inside the unit and may cause a fire.
Bolt Stud
(Included)
Heat sink
Metal
Mounting
Strap
1
*
This unit
Ground Lead
Chassis
Reinforce the head unit with the metal mounting
strap (not supplied). Secure the ground lead of the
unit to a clean metal spot using a screw (*1) already
attached to the vehicle’s chassis.
Detachable Front
Panel
•
For the screw marked “*2”, use an appropriate screw for the chosen
mounting location.
Caution
Connect each input lead coming from an amplifier to
the corresponding output lead coming from the left
rear of the CDE-130R/CDE-130RM/CDE-130RR.
Connect all other leads of the CDE-130R/CDE-
130RM/CDE-130RR according to details described in
the CONNECTlONS section.
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
•
The main unit must be mounted within 30 degrees of the horizontal
plane, back to front.
3
Slide the CDE-130R/CDE-130RM/CDE-130RR into the
dashboard until it clicks. This ensures that the unit is
properly locked and will not accidentally come out
from the dashboard. Install the detachable front panel.
Less than 30°
Removal
1. Remove the detachable front panel.
2. Insert the bracket keys into the unit, along the guides
on either side. The unit can now be removed from the
mounting sleeve.
Rubber Cap
(Included)
1
This unit
Bracket
Bolt Stud
(Included)
Bracket Keys
(Included)
Dashboard
Mounting Sleeve
(Included)
3. Pull the unit out, keeping it unlocked as you do so.
Snapping Point
This unit
<JAPANESE CAR>
Remove the mounting sleeve from the main unit
(see “Removal”).
Front Frame
(Included)
Screws (M5 × 8)
This unit
Ground Lead
*3
Mounting Bracket
Secure the ground lead of the unit to a clean metal spot using a screw
(*3) already attached to the vehicle’s chassis.
18-EN
Connections
Antenna
To Amplifier
To Power Antenna
(Red)
IGNITION
(Blue/White)
(Black)
Ignition Key
BATTERY
(Yellow)
Battery
(Green)
Rear Left
Front Left
Rear Right
(Green/Black)
(White)
(White/Black)
(Grey)
(Grey/Black)
(Violet)
Front Right
(Violet/Black)
Speakers
Speakers
Front Left
Amplifier
Front Right
19-EN
1
2
3
Antenna Receptacle
ISO Connector
@
#
$
%
^
&
Rear Right (−) Speaker Output Lead (Grey)
Rear Right (+) Speaker Output Lead (Grey/Black)
Front Right (−) Speaker Output Lead (Violet)
Front Right (+) Speaker Output Lead (Violet/Black)
Fuse Holder (15A)
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
Front Output RCA Connectors
RED is right and WHITE is left.
4
Power Antenna Lead (Blue/White)
Connect this lead to the +B terminal of your power antenna,
if applicable.
Note
*
(
RCA Extension Cable (sold separately)
Front AUX Input Terminal
This terminal allows for input of audio from an external
device (such as a portable player), using a commercially-
available converter cable.
•
This lead should be used only for controlling the vehicle’s
power antenna. Do not use this lead to turn on an amplifier or a
signal processor, etc.
)
-
USB Connection Terminal
Connect USB memory (sold separately)
5
6
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Steering Remote Control Interface Connector
To steering remote control interface box.
You can operate this unit from the vehicle’s control unit when
an Alpine Steering Remote Control Interface Box (optional)
is connected. For details, contact your Alpine dealer.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
7
8
9
0
!
ISO Power Supply Connector
Rear Left (+) Speaker Output Lead (Green)
Rear Left (−) Speaker Output Lead (Green/Black)
Front Left (+) Speaker Output Lead (White)
Front Left (−) Speaker Output Lead (White/Black)
To prevent external noise from entering the audio system.
•
•
•
•
Locate the unit and route the leads at least 10 cm away from the car harness.
Keep the battery power leads as far away from other leads as possible.
Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
•
Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
20-EN
|