SETTING THE LANGUAGE
4.(AT-50CWLD only) Connect the supplied
AC adapter to the unit and to the wall out-
let.
Your caller ID unit can display messages in
English, French and Spanish. The default
language setting is English. After inserting
the batteries do the following:
* The number of new
calls in memory
* The New Call indi-
cator flashing.
1.When English is displayed after inserting
batteries, select language English
French/Spanish using the REVIEW.5.key.
Each press of the REVIEW 5 key will
change the displayed language.
AT-50LD
The red New Call LED will be flashing to
indicate new calls are in memory.
The LED will turn off after all new calls are
reviewed.
AT-50CWLD
Desk Mounting Position 1
2.Press the DELETE not REVIEW 2 to set
the displayed language.
Caller ID with Large Display
REVIEWING NEW CALLER ID CALLS
If the New Call LED is flashing pressing
REVIEW 5or 2key to scroll through all new
information (newest calls to oldest calls).
After the last new call is reviewed, END OF
NEW CALL is displayed and the New Call
LED turns off.
Note: The answering machine must be set
to answer after at least 2 rings to properly
receive Caller ID data.
SETTING THE LOCAL AREA CODE
(AT-50CWLD only)
After selecting a language for the display,
you’ll need to program your area code in to
the unit so it can properly recognize and dial
calls using he CALLBACK feature.
If you are in an area that doesn’t allow 7
digit dialing enter “010” for the area code.
1.Press the REVIEW 5 or REVIEW 2 key
to select each digit.
2.Press the “DELETE” key to set the number,
not the REVIEW key.
RECEIVING CALLER ID CALLS
The AT50LD/CWLD will receive and store
up to 50 Caller ID calls in the memory. If 50
calls are in the memory, any new calls
received will be saved by replacing the old-
est in the memory. When a call is received
the display will show the following:
Note: If all new calls are not reviewed after
20 seconds the display will show the
number of new calls remaining in memory.
The New Call LED will be flashing.
Desk Mounting Position 2
CONNECTING TO A TELEPHONE
1.Connect the line cord from the wall jack
into the jack marked LINE on the Caller ID.
2.Connect the supplied 7-foot line cord from
the jack marked PHONE on the unit to the
line jack on the telephone.
3.(AT-50CWLD only) Connect the supplied
AC adapter to the unit and the wall outlet.
4.Check for a dial tone to ensure proper
Important: To receive information about
incoming telephone calls, you must sub-
scribe to the Caller ID and/or Call Waiting
services provided by your local telephone
company; there is a fee for this service and
it may not be available in all areas.
REVIEWING OLD CALLER ID CALLS
When the New Call LED is off, pressing
REVIEW 5 key will scroll through all call
records from oldest to newest. Pressing the
REVIEW 2 key will scroll through all calls
newest to oldest. END OF LIST is displayed
* Caller’s Name
3. There will not be a beep comfirmation
* Caller’s Number
* Date and Time of Call
* New Call Indicator
connection.
Note: The display will show the name or
number from the calling party if available. If
the caller’s information is blocked the display
will show PRIVATE CALL. If the call informa-
tion is not available or outside the calling
area, the display will show OUT OF AREA
between the first and last call record in memory.
Note: When an area code digit is flashing,
continue pressing the REVIEW 5or REVIEW
2key until the correct digit appears. Press
DELETE to set the digit.
BATTERY INSTALLATION
Before operating your Caller ID install 4 alkaline
batteries in the AT50LD or 2 alkaline batteries in
the AT50CWLD in the battery compartment
located on the bottom of the unit. The screw
must be remooved to open the battery door.
Using the illustration, observe battery polarity
(+ or -) during installation.
Note: After 20 seconds with no keys pressed
the date and time screen will be displayed.
RECEIVING REPEAT CALLS
Note: After the language and area codes
are set, should you require changing them
press and hold both REVIEW 5and REVIEW
2keys for approximately 8 seconds. The
unit will default to setup mode.
When a call is received more that once the
Caller ID will only use one memory location
for the call. This will save call memory space.
DELETING CALL RECORDS
To delete a call record, press the REVIEW
5oor 2 key to locate the call record wish
to delete. Press DELETE twice quickly and the
call record will be removed and the next call
in memory will be displayed.
WARNING: Your Caller ID must be
disconnected from the telephone line
before inserting or changing batteries.
When a repeat call is received the REPEAT
indicator will turn on. The date and time of
the call will be updated and the call will be
moved from its current memory location to
the newest call received.
When a new call is received the real-time
clock will automatically be updated by the
current date and time received from the tele-
phone company. It is not possible to manu-
ally set the date and time.
1.Turn the unit over.
2.Remove the screw from the battery door and
lift the battery door away from the base.
Note: (AT-50CWLD only) You must
wait for at least 2 rings to get Caller ID data.
A telephone does not need to be connected
in order for it to work, but is recommended
for the callback feature and necessary for
the Caller ID on the Call Waiting feature.
DELETING ALL CALL RECORDS
To delete all records press and hold DELETE
key for approximately 8 seconds. All calls
will be automatically erased. DELETE ALL
will not appear on the screen.
The REPEAT indicator will be displayed for
all repeat calls during NEW CALL review
indicating the caller has called more that
once.
DESK AND WALL MOUNTING.
Attach the pedestal to the bottom or back of
the unit in the desired desk mount position
(see illustration). For wall mounting, first
detach the pedestal and mount the unit
directly to the wall using two screws (not pro-
vided)
CONNECTING TO AN ANSWERING
MACHINE
Note: The New Call counter will not incre-
ment for a repeat call.
AAA
1.Connect the line cord from the wall jack
into the jack marked LINE on the Caller ID
2.Connect the supplied 7-foot line cord from
the jack marked PHONE on the unit to the
IN jack on your answering machine.
3.Connect a line cord from the answering
machine to the line jack on your tele-
phone.
➥
NEW CALLS
When a new call is received the NEW indi-
cator will turn on and the LCD display will
show the call record information. After 20
seconds the display will show:
RECEIVING CALLER ID ON CALL
WAITING (AT-50CWLD only)
The Caller ID will receive name and number
of an incoming call while you are on the
phone. When a call waiting call is received
the display will show the following:
3.Insert the batteries as shown.
4.Replace the battery door and screw. (Be
sure to tigten the screw completely.)
|